i3 International S244 User manual

DEFAULT LOGIN INFORMATION
i3’s S244 managed switch delivers 24 (10M/100M/1G) RJ45/PoE/PoE+
ports plus 2 SFP Gigabit ports and offers even better cost performance
and lower total cost of ownership. The 370 Watts of PoE/PoE+ power
budget makes it ideal for 24 IP cameras. The S244 is simple to install
and configure using a web browser.
PACKAGE CONTENTS
In addition to the switch ensure that the following items are included:
i3 INTERNATIONAL INC. 1.866.840.0004
www.i3international.com
1. Install S244 PoE Switch on a dedicated shelf or inside a rack, as required.
Ensure sufficient airflow all around the unit. Avoid locations with high levels of
dust, vibrations, or humidity.
Note: Mounting hardware is site-specific and must be supplied by the
installer.
2. Plug in the provided power cord into a AC power supply. Then plug the cord
into the power port on the back panel of the switch. The switch will power on
automatically.
Important: The use of UPS is highly recommended by i3 International. Power
surge damage is not covered by i3 warranty.
3. Using CAT5e (or better) cable connect the Switch to the SRX-Pro (NVR) or
networked PC using one of the 24 PoE ports (preferred) or one of the SFP
ports, using the SFP Copper RJ45 transceiver (not provided).
4. Use CAT5e (or better) cable not exceeding 328 ft (100 meters) to plug in up to
24 IP cameras into the RJ45 switch ports. Consider the total 370 Watt switch
power budget.
INSTALLATION INSTRUC TIONS
i3-TRNG-Switches-S244.indd
Log into the switch through a networked PC. Enter the S244 default IP
Address into the web browser.
Default IP Address - 192.168.0.10
Default Username - i3admin
Default Password - i3admin1
LED LED Status Description
System Green, Solid Switch is powered on
Link/Act/
Speed
Green, Blink Connection is 1Gbps
Amber, Blink Connection is 10/100Mbps
PoE Green, Solid PoE on
LED INDICATORS
Press the Mode button to switch between “Link/Act/Speed” and “PoE” modes.
Power Cord Rubber Feet x4Rackmount Brackets x2 Bracket screws x8
System LED
Mode LEDs Mode/Reset Button Port Status LEDs
10/100/1000 RJ45 Ports 100/1000 SFP Ports
Port Connections 24x 10/100/1000 RJ45 connector ports
2x SFP Gigabit ports
PoE Function PoE ports: 24
PoE Budget: 370 Watts
Supports IEEE802.3at (PoE+ 30W)
Supports IEEE802.3af (PoE 15.4W)
Hardware Performance Forwarding Capacity: 38.68Mpps
Switching Capacity: 52Gbps
Mac Table: 8K
Jumbo Frames: 9216 Bytes
Environment Operating Temperature: 32-122°F (0-50°C)
Storage Temperature: -4-158°F (-20-70°C)
Humidity: 10 to 90% RH (non-condensing)
Mechanism Dimensions (L x W x H): 17½ x 8⅜x 1¾
inches (442 x 211x 44 mm)
Weight: 7.3 lbs (3.3 Kg)
Power Supply AC input: 100-240 VAC, 50~60Hz
Maximum Power consumption: 437 Watts
(PoE power included).
Certifications CE, FCC Part 15 Class A, UL
Quick Start Guide
S244. 24-Port PoE+ Switch
PoE PoE
PoE
PoE
S244
802.3af 802.3af
802.3af
802.3af
NVR
5. The LED indicators will glow to indicate
the switch is powered on and supplying
power to the connected devices.
Rev. 220714
TECHNICAL SPECIFICATIONS

S244, 24-Port PoE+ Switch
QUICK START GUIDE
SWITCH ACTIVATION WIZARD
After logging in with default administrative credentials (i3admin /
i3admin1), switch activation wizard will automatically launch.
As part of the initial switch setup, you must change the default
administrative password, for the security of your network.
1. CHANGE DEFAULT PASSWORD
Enter New password and re-enter new password to confirm.
Your new password must follow the minimum password rules:
The password must:
• Be at least 8 characters long
• Contain at least 2 of the following: numbers, lower- and
upper-case letters, special characters.
IMPORTANT: These special characters are not supported
/ \ : * ? ‘ “ < > | %
4. SET SYSTEM INFORMATION (OPTIONAL)
When done, click SET PASSWORD.
Note: To set the switch credentials to i3 default (i3admin/i3admin1),
click SET i3 PASSWORD. This option is not secure and is not
recommended and should only be used if IP Camera network is
isolated. Use at own risk.
2. SET IP ADDRESS
• Select Set IP Address manually (recommended)
• Enter IP address
• Enter Subnet mask
• Enter Default router
• Enter DNS address (optional)
• Click Next
i3 INTERNATIONAL INC. 1.866.840.0004
www.i3international.com
ACT Download &
Documentation
Scan this QR code or visit ftp.i3international.com to view
and download AnnexxusConfigurationTool v1.9 (ACT).
Contact our Technical Support team at: 1.877.877.7241 or
[email protected] if you have any questions
or concerns regarding camera installation or if you require
software services or support.
3. SET DATE AND TIME (OPTIONAL)
• Automatic date and time is pre-enabled (recommended). Turn off to
set the time manually.
• Enter Server Address (optional)
• Select the Time zone from the drop-down list (optional)
• Click Next
• Enter system contact (optional)
• Enter switch name (optional)
• Enter system location (optional)
• Click Apply