IAG Performance IAG-ACC-F3067 User manual

IAG-ACC-F3067 - IAG Removable Dual Rear
Cup Holder for Two & Four Door 2021+
Ford Bronco
Part# IAG-ACC-F3067
Congratulations on the purchase of your IAG Removable Dual Rear Cup Holder, and
thank you for choosing IAG Performance. These instructions are intended for users
with basic mechanical skills. Professional installation is not required. The average
installation time is 10 minutes
Step 1/11
IAG-ACC-F3067 - IAG Removable Dual Rear Cupholder for Two Door & Four Door 2021+ Ford Bronco rev. | 46818 v1 [Published] 2022-11-30 14:02 UTC
IAG Performance 1/6

IAG-ACC-F3067 - IAG Removable Dual
Rear Cup Holder for Two & Four Door
2021+ Ford Bronco
Part# IAG-ACC-F3067
Tools Required For Installation:
T20 Torx Driver
Step 2/11
Step 3/11
Numbered annotations (1)
1
1
Grasp the rear console cover at the
top and pull towards the back of the
vehicle to release the clips.
IAG-ACC-F3067 - IAG Removable Dual Rear Cupholder for Two Door & Four Door 2021+ Ford Bronco rev. | 46818 v1 [Published] 2022-11-30 14:02 UTC
IAG Performance 2/6

Step 4/11
Numbered annotations (1)
2
Step 5/11
Numbered annotations (1)
3
2
Disconnect the wiring harnesses by
pressing the release lever and pulling
the harness connector out.
3
Locate the two T20 torx screws at the
bottom of the console cover. Remove
both screws.
IAG-ACC-F3067 - IAG Removable Dual Rear Cupholder for Two Door & Four Door 2021+ Ford Bronco rev. | 46818 v1 [Published] 2022-11-30 14:02 UTC
IAG Performance 3/6

Step 6/11
Numbered annotations (1)
4
Step 7/11
Numbered annotations (1)
5
4
Line up the holes in the cup holder
bracket where the two T20 torx
screws were previously removed.
Start threading the screws through
the cup holder bracket into the
console cover but do not tighten fully.
5
*Special Note*
The cupholder bracket should be
adjusted up as close as possible to
the console cover if your Bronco is
equipped with floor mats that cover
the transmission hump. The
cupholder bracket should be adjusted
down towards the bottom of the
console cover if you do not have floor
mats.
IAG-ACC-F3067 - IAG Removable Dual Rear Cupholder for Two Door & Four Door 2021+ Ford Bronco rev. | 46818 v1 [Published] 2022-11-30 14:02 UTC
IAG Performance 4/6

Step 8/11
Numbered annotations (1)
6
Step 9/11
Numbered annotations (1)
7
6
Once the cupholder bracket has
been adjusted appropriately, tighten
the two T20 Torx screws.
7
Reconnect the wiring harnesses that
were previously disconnected.
IAG-ACC-F3067 - IAG Removable Dual Rear Cupholder for Two Door & Four Door 2021+ Ford Bronco rev. | 46818 v1 [Published] 2022-11-30 14:02 UTC
IAG Performance 5/6

Step 10/11
Numbered annotations (1)
8
Step 11/11
Numbered annotations (1)
9
8
Reinstall the console cover on the
center console by lining up the clips
and pushing forward until the clips
engage. If you have floor mats, you
may need to install the console cover
over the lip of the floor mat.
9
Install the cupholder onto the
bracket. It is held in place by a
magnet and two locating pins. The
cupholder can be easily removed for
cleaning as well as if the rear seats
are folded down.
IAG-ACC-F3067 - IAG Removable Dual Rear Cupholder for Two Door & Four Door 2021+ Ford Bronco rev. | 46818 v1 [Published] 2022-11-30 14:02 UTC
IAG Performance 6/6