IBA BM-DIS-i-8o User manual

Data distributor
ibaBM-DIS-i-8o
Manual
Issue 1.2

Manufacturer
iba AG
Koenigswarterstr. 44
90762 Fuerth
Germany
Contacts
Main office
[phone]
Fax
[phone]
Support
[phone]
Engineering
[phone]
E-Mail: [e-mail]
Web: www.iba-ag.com
This manual must not be circulated or copied, or its contents utilized and disseminated,
without our express written permission. Any breach or infringement of this provision will
result in liability for damages.
©iba AG 2016, All Rights Reserved
The content of this publication has been checked for compliance with the described hard-
ware and software. Nevertheless, deviations cannot be excluded completely so that the
full compliance is not guaranteed. However, the information in this publication is updated
regularly. Required corrections are contained in the following regulations or can be down-
loaded on the Internet.
The current version is available for download on our web site http://www.iba-ag.com.
Protection note
Windows®is a label and registered trademark of the Microsoft Corporation. Other prod-
uct and company names mentioned in this manual can be labels or registered trade-
marks of the corresponding owners.
Certification
The device is certified according to the European standards and directives. This device
corresponds to the general safety and health requirements. Further international cus-
tomary standards and directives have been observed.
Issue
Date
Revision
Chapter / pages
Author
Version
HW/FW
1.2
07/19/2016
New operation mode
4.6

ibaBM-DIS-i-8o
Manual
Issue 1.2
3
Table of contents
1About this manual...........................................................................................5
1.1 Target group ..................................................................................................5
1.2 Designations..................................................................................................5
1.3 Used symbols................................................................................................6
2Safety instructions..........................................................................................7
2.1 Designated use..............................................................................................7
2.2 Designated environment of use .....................................................................7
2.3 Special safety advice.....................................................................................7
3Scope of delivery ............................................................................................7
4Product properties..........................................................................................8
4.1 Description.....................................................................................................8
4.2 Modes of operation........................................................................................8
4.2.1 Copy mode....................................................................................................8
4.2.2 Distribution mode...........................................................................................9
4.2.3 Copy and cut mode........................................................................................9
4.3 Certificates...................................................................................................10
4.4 Device views................................................................................................10
4.4.1 Front view....................................................................................................10
4.4.2 Top view ......................................................................................................11
4.4.3 Bottom view.................................................................................................11
4.5 Indicators.....................................................................................................12
4.6 Operating elements .....................................................................................12
4.7 Principle diagram.........................................................................................13
5Operation.......................................................................................................14
5.1 Requirements..............................................................................................14
5.2 Application...................................................................................................14
5.2.1 Copy mode..................................................................................................14
5.2.2 Distribution mode.........................................................................................16
5.2.3 Copy and cut mode......................................................................................16
6Installation, Connection, Disassembly........................................................17
6.1 Installation ...................................................................................................17
6.2 Connection ..................................................................................................17
6.3 Disassembly................................................................................................17
7Technical data ...............................................................................................18
7.1 Main data.....................................................................................................18
7.2 Dimension sheet..........................................................................................20

Manual
ibaBM-DIS-i-8o
4
Issue 1.2
8Support and contact..................................................................................... 21

ibaBM-DIS-i-8o
Manual
Issue 1.2
5
1 About this manual
This manual describes the construction, the use and the operation of the device
ibaBM-DIS-i-8o.
1.1 Target group
This manual addresses in particular the qualified professionals who are familiar with
handling electrical and electronic modules as well as communication and measurement
technology. Aperson is regarded to as professional if he/she is capable of assessing
safety and recognizing possible consequences and risks on the basis of his/her spe-
cialist training, knowledge and experience and knowledge of the standard regulations.
1.2 Designations
The following designations are used in this manual:
Action
Designations
Menu command
Menu „Logic diagram“
Call of menu command
„Step 1 – Step 2 –Step 3 –Step x”
Example:
Select menu „Logic diagram –Add –New logic dia-
gram ”
Keys
<Key name>
Example: <Alt>; <F1>
Press keys simultaneously
<Key name> + <Key name>
Example:
<Alt> + <Ctrl>
Buttons
<Button name>
Example:
<OK>; <Cancel>
File names, Paths
„File name“, „Path”
Example:
„Test.doc“

Manual
ibaBM-DIS-i-8o
6
Issue 1.2
1.3 Used symbols
If safety instructions or other notes are used in this manual, they mean:
The non-observance of this safety information may result in an imminent risk of death
or severe injury:
By an electric shock!
Due to the improper handling of software products which are coupled to input and
output procedures with control function!
If you do not observe the safety instructions regarding the process and the system or
machine to be controlled, there is a risk of death or severe injury!
The non-observance of this safety information may result in a potential risk of death or
severe injury!
The non-observance of this safety information may result in a potential risk of injury or
material damage!
Note
A note specifies special requirements or actions to be observed.
Important note
Note if some special features must be observed, for example exceptions from the rule.
Tip
Tip or example as a helpful note or insider tip to make the work a little bit easier.
Other documentation
Reference to additional documentation or further reading.

ibaBM-DIS-i-8o
Manual
Issue 1.2
7
2 Safety instructions
2.1 Designated use
The device is electrical equipment. It may be used only in the following applications:
Automation of industrial systems
Measurement data logging and analysis
Applications of iba software products (ibaPDA, ibaLogic etc.) and iba hardware
products
The device must not be operated in mains supply circuits!
2.2 Designated environment of use
The device should only be operated and stored under conditions as described in chapter
“Technical data”.
2.3 Special safety advice
Do not open the device!
3 Scope of delivery
Check after unpacking the completeness and intactness of the delivery.
The scope of delivery includes:
Device ibaBM-DIS-i-8o
2-pole connector (power supply)
Manual
Additional accessories not included in delivery, please see www.iba-ag.com

Manual
ibaBM-DIS-i-8o
8
Issue 1.2
4 Product properties
4.1 Description
The device ibaBM-DIS-i-8o is a member of iba’s device family for distribution of signals
via fiber optic cables. The device can be operated in several modes:
Copy mode
Distribution mode
Copy and cut mode
4.2 Modes of operation
4.2.1 Copy mode
In copy mode 1 incoming fiber optic data stream is copied to 9 fiber optic output links.
The output signal follows the input signal with minimum delay and without any modifica-
tion. All via ibaNet fiber optics transmitted signals of any ibaNet protocol type can serve
as an input signal. The device automatically detects the type of input signal and adjusts
the output links accordingly.
Application
Connecting one fiber optic cable to multiple input devices
As a replacement for the device ibaBM-FOX-i-3o, with more outputs and support of
32 Mbit/s link protocol
Distribution of synchronization signals, for synchronizing multiple measurement de-
vices by one fiber optic source.
Figure 1: Principle of copy mode
Note
5 Mbit/s link protocol: Only uni-directional mode is supported.

ibaBM-DIS-i-8o
Manual
Issue 1.2
9
4.2.2 Distribution mode
In distribution mode 1 incoming fiber optic data stream, transmitted at 32 Mbit/s and
containing 512 analog and 512 digital signals, is split into 8 fiber optic output streams,
containing 64 analog and 64 digital signals each and transmitted at 3.3 Mbit/s.
An additional output provides for a mirrored input data stream. If necessary this output
can be used to feed more devices interconnected in a daisy chain. In distribution mode
the device works in the opposite way like an ibaBM-COL-8i-o.
Application
Supply of up to 8 ibaNet750 nodes (or similar devices) by 1 fiber optic output.
Reduction of fiber optic cabling over long distances
Collection of 8 input lines by ibaBM-COL-8i-o, transmission over one fiber optic
conductor and redistribution on 8 output links by ibaBM-DIS-i-8o.
Figure 2: Principle of distribution mode
4.2.3 Copy and cut mode
In copy and cut mode 1 incoming fiber optic data stream with 32 Mbit/s is copied to 8
outputs and reduced to 3.3 Mbit/s. Each fiber optic stream with 32 Mbit/s, respectively
32Mbit ibaNet protocol, can be used as incoming signal. Depending on the cycle time,
the telegrams are cut and only the first bytes are transmitted.
In copy and cut mode, it is important, that data to be transmitted are written at the begin-
nig of the 32Mbit telegram.
The data type at the output side corresponds to the data type of the 32Mbit input. The
data type at the 3.3 Mbit/s output side can be either INT (e. g. for ibaPADU-8) or REAL
(e. g. for ibaLink-SM-64-io).
When the cycle time is ≥100 µs , the first 256 bytes of analog data and the first 8 bytes
of digital data are copied to the outputs.
When the cycle time is < 100 µs, the first 128 bytes of analog data and the first 8 bytes
of digital data are copied to the outputs.

Manual
ibaBM-DIS-i-8o
10
Issue 1.2
4.3 Certificates
The device is certified according to:
CE
FCC (Class B)
4.4 Device views
4.4.1 Front view
1
2
3
4
5
6
7
8
Operating status indicators L1 … L4
On/off switch (S11)
Connector for power supply 24 V X14
Rotary switch S1
Connection FO input (RX) X10
Connection FO output (TX) X11
Connection FO outputs (TX) X34 … X37
Connection FO outputs (TX) X30 … X33
Figure 3: Front view