IBASE Technology IBQ800 Series User manual

IBQ800 Series
Qseven CPU Module
With Intel®Atom™ x7/x5
User’s Manual
Version 1.0
(Oct. 2018)

ii
IBQ800 Series User’s Manual
Copyright
©2018 IBASE Technology, Inc. All rights reserved.
No part of this publication may be reproduced, copied, stored in a retrieval
system, translated into any language or transmitted in any form or by any
means, electronic, mechanical, photocopying, or otherwise, without the prior
written consent of IBASE Technology, Inc. (hereinafter referred to as
“IBASE”).
Disclaimer
IBASE reserves the right to make changes and improvements to the
products described in this document without prior notice. Every effort has
been made to ensure the information in the document is correct; however,
IBASE does not guarantee this document is error-free.
IBASE assumes no liability for incidental or consequential damages arising
from misapplication or inability to use the product or the information
contained herein, nor for any infringements of rights of third parties, which
may result from its use.
Trademarks
All the trademarks, registrations and brands mentioned herein are used for
identification purposes only and may be trademarks and/or registered
trademarks of their respective owners.

IBQ800 Series User’s Manual
iii
Compliance
This product has passed CE tests for environmental specifications and
limits. This product is in accordance with the directives of the European
Union (EU). In a domestic environment, this product may cause radio
interference in which case users may be required to take adequate
measures.
This product has been tested and found to comply with the limits for a Class
B device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with manufacturer’s
instructions, may cause harmful interference to radio communications.
WEEE
This product must not be disposed of as normal household
waste, in accordance with the EU directive of for waste
electrical and electronic equipment (WEEE - 2012/19/EU).
Instead, it should be disposed of by returning it to a
municipal recycling collection point. Check local
regulations for disposal of electronic products.
Green IBASE
This product is compliant with the current RoHS
restrictions and prohibits use of the following substances
in concentrations exceeding 0.1% by weight (1000 ppm)
except for cadmium, limited to 0.01% by weight (100 ppm).
•Lead (Pb)
•Mercury (Hg)
•Cadmium (Cd)
•Hexavalent chromium (Cr6+)
•Polybrominated biphenyls (PBB)
•Polybrominated diphenyl ether (PBDE)

iv
IBQ800 Series User’s Manual
Important Safety Information
Carefully read the precautions before using the board.
Environmental conditions:
•Use this product in environments with ambient temperatures between
-40˚C and 85˚C.
•Do not leave this product in an environment where the storage
temperature may be below 40°C or above 90°C. To prevent from
damages, the product must be used in a controlled environment.
Care for your IBASE products:
•Before cleaning the PCB, unplug all cables and remove the battery.
•Clean the PCB with a circuit board cleaner, degreaser or use cotton
swabs and alcohol.
•Vacuum the dust with a computer vacuum cleaner to prevent the fan
from being clogged.
WARNING
Attention during use:
•Do not use this product near water.
•Do not spill water or any other liquids on this product.
•Do not place heavy objects on the top of this product.
Anti-static precautions
•Wear an anti-static wrist strap to avoid electrostatic discharge.
•Place the PCB on an anti-static kit or mat.
•Hold the edges of PCB when handling.
•Touch the edges of non-metallic components of the product instead of
the surface of the PCB.
•Ground yourself by touching a grounded conductor or a grounded bit of
metal frequently to discharge any static.
CAUTION
Danger of explosion if the internal lithium-ion battery is replaced by an
incorrect type. Replace only with the same or equivalent type recommended
by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions or recycle them at a local recycling facility or
battery collection point.

IBQ800 Series User’s Manual
v
Warranty Policy
•IBASE standard products:
24-month (2-year) warranty from the date of shipment. If the date of
shipment cannot be ascertained, the product serial numbers can be
used to determine the approximate shipping date.
•3rd-party parts:
12-month (1-year) warranty from delivery for the 3rd-party parts that are
not manufactured by IBASE, such as CPU, CPU cooler, memory,
storage devices, power adapter, panel and touchscreen.
＊PRODUCTS, HOWEVER, THAT FAIL DUE TO MISUSE, ACCIDENT,
IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE
TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE
BILLED FOR REPAIR AND SHIPPING CHARGES.
Technical Support & Services
1. Visit the IBASE website at www.ibase.com.tw to find the latest
information about the product.
2. If you need any further assistance from your distributor or sales
representative, prepare the following information of your product and
elaborate upon the problem.
•Product model name
•Product serial number
•Detailed description of the problem
•The error messages in text or in screenshots if there is any
•The arrangement of the peripherals
•Software in use (such as OS and application software, including the
version numbers)
3. If repair service is required, you can download the RMA form at
http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the
form and contact your distributor or sales representative.

vi
IBQ800 Series User’s Manual
Table of Contents
Compliance.....................................................................................iii
Important Safety Information........................................................iv
Warranty Policy ...............................................................................v
Technical Support & Services .......................................................v
Chapter 1 General Information.............................................1
1.1 Introduction .........................................................................................2
1.2 Features..............................................................................................2
1.3 Packing List.........................................................................................3
1.4 Specifications......................................................................................3
1.5 Block Diagram.....................................................................................5
1.6 Overview.............................................................................................6
1.7 Dimensions .........................................................................................7
Chapter 2 PinDefinition...........................................................9
2.1 Connector Location ...........................................................................10
2.1.1 Edge Connector...................................................................11
Chapter 3 Drivers Installation.............................................15
3.1Introduction .......................................................................................16
3.2 Intel®Chipset Software Installation Utility..........................................16
3.3 Graphics Driver Installation ...............................................................18
3.4 HD Audio Driver Installation...............................................................20
3.5 Intel®Trusted Execution Engine Drivers............................................22
3.6 Intel®Serial IO Drivers ......................................................................24
3.7 LAN Driver Installation.......................................................................26
Chapter 4 BIOS Setup..........................................................29
4.1 Introduction .......................................................................................30
4.2 BIOS Setup.......................................................................................30
4.3 Main Settings ....................................................................................31
4.4 Advanced Settings ............................................................................31
4.4.1 Trusted Computing...............................................................32
4.4.2 ACPI Settings.......................................................................33

IBQ800 Series User’s Manual
vii
4.4.3 LVDS (eDP/DP) Configuration..............................................34
4.4.4 Fintek 81964 SIO Configuration............................................35
4.4.5 Fintek 81804 SIO Configuration............................................38
4.4.6 Fintek 81804 Hardware Monitor............................................39
4.4.7 CPU Configuration................................................................40
4.4.8 AMI Graphic Output Protocol Policy......................................41
4.4.9 Network Stack Configuration ................................................42
4.4.10 CSM Configuration ...............................................................43
4.4.11 SDIO Configuration...............................................................44
4.4.12 USB Configuration................................................................45
4.5 Chipset Settings ................................................................................46
4.5.1 HD-Audio Configuration........................................................47
4.5.2 PCI Express Configuration....................................................47
4.5.3 SATA Drives.........................................................................48
4.5.4 SCC Configuration................................................................49
4.5.5 USB Configuration................................................................50
4.6 Security Settings................................................................................51
4.6.1 Secure Boot..........................................................................52
4.7 Boot Settings.....................................................................................53
4.8 Save & Exit Settings ..........................................................................54
Appendix ........................................................................................55
A. I/O Port Address Map ........................................................................56
B. Interrupt Request Lines (IRQ)............................................................58
C. Watchdog Timer Configuration ..........................................................59

viii
IBQ800 Series User’s Manual
This page is intentionally left blank.

1
Chapter 1
General Information
The information provided in this chapter includes:
•Features
•Packing List
•Optional Accessories
•Specifications
•Block Diagram
•Board Overview
•Board Dimensions

2
IBQ800 Series User’s Manual
1.1 Introduction
IBQ800 is a CPU module in Qseven form factor with the Intel®Atom™x7/x5
processor, and its size is smaller than other computer-on-module standards
like COMe or ETX. It comes with a 230-pin MXM2 SMT edge connector for
the power and signal lanes connection to a carrier board. It also features the
LPDDR4 onboard memory, TPM 2.0, SDIO, and optional eMMC 5.0.
Photo of IBQ800
1.2 Features
•Onboard Intel®Atom™ x7-E3950 / x5-E3930 processor
•Onboard LPDDR4 memory
•Intel®I210IT PCIe GbE LAN
•Wide-range operating temperature
•Configurable watchdog timer and TPM 2.0
•eMMC 5.0 (Optional)

General Information
IBQ800 Series User’s Manual
3
1
1.3 Packing List
Your product package should include the items listed below. If any of the
items below is missing, contact the distributor or dealer from whom you
purchased the product.
•IBQ800 Qseven CPU Module
•Disk (including drivers and flash memory utility)
•This User’s Manual
1.4 Specifications
Product Name
•IBQ800-x7LVe8G: E3950 + LVDS + eMMC + 8 GB memory
•IBQ800-x5LVe8G: E3930 + LVDS + eMMC + 8 GB memory
•IBQ800-x5LVe: E3930 + LVDS + eMMC + 4 GB memory
•IBQ800-x5: E3930 + eDP + 4 GB memory
“IBQ800”will be the model name printed on PCB surface
Form Factor
Qseven R2.1
CPU Type /
Speed
•Intel®AtomTM QC x7 E3950, 2GHz, 2MB cache, 12W TDP
(IBQ800-I50)
•Intel®AtomTM DC x5 E3930, 1.8GHz, 2MB cache, 6W TDP
(IBQ800-I30)
Package = FCBGA1296,Type-3,
31 x 24 x 1.318 mm,14 nm, Tj= -0ﾟC to +105ﾟC
BIOS
AMI BIOS
Memory
Intel®AtomTM SoC integrated memory controller
- Onboard LPDDR4 1600MHz 8GB or 4GB
Graphics
Intel®SoC integrated Gen9-LP
Display
1 x DDI port, thru NXP PTN3460 for eDP to LVDS, or 1 x eDP
LAN
Intel®I210IT GbE x 1, thru an RJ45 on carrier board
USB
Derived from Qseven CPU module:
•3 x USB 3.0
•4 x USB 2.0
Expansion
4 x PCIe (x1)
SATA
2 x SATA 3.0 (6Gb/sec.) thru interface on carrier board
Audio
Intel®AtomTM SoC built-in HD Audio controller

4
IBQ800 Series User’s Manual
eMMC
Onboard eMMC 5.0, 32GB (Optional),
supports Windows & Linux O.S boot only)
TPM 2.0
Yes
SD
1 x SD 3.0
Super I/O
Fintek F81804U-I, supports 1 x UART ports (RX/ TX/ RTS/ CTS
only) and 4-second delay to power off
Watchdog
Timer
Yes (256 segments, 0= disable ,1, 2…255. sec/min)
H/W Monitor
Yes
Connector to
Carrier Board
One 230-pin golden finger (Qseven 2.1 standard)
Power
+5V, 5VSB
Certification
CE (EN55032:2012), FCC Class B
OS support
•Windows 10 (64-bit)
•Linux (Ubuntu)
Board Size
70 x 70 mm (2.76” x 2.76”)
RoHS
Yes
Temperature
•Operating: -40 ~ 85 °C (-40 ~ 185 °F)
•Storage: -40 ~ 90 °C (-40 ~ 194 °F)
Relative
Humidity
90%, non-condensing at 60°C
Others
Heat spreader
IP416 will be the carrier board for testing
All specifications are subject to change without prior notice.

General Information
IBQ800 Series User’s Manual
5
1
1.5 Block Diagram

6
IBQ800 Series User’s Manual
1.6 Overview
Top View
Bottom View
Photos of IBQ800
＊The photos above are for reference only. Some minor components may
differ.

General Information
IBQ800 Series User’s Manual
7
1
1.7 Dimensions
Unit: mm

8
IBQ800 Series User’s Manual
This page is intentionally left blank.

9
Chapter 2
Pin Definition
This section provides the pin definition of the 230-pin MXM2
SMT edge connector.

10
IBQ800 Series User’s Manual
2.1 Connector Location
Board diagram of IBQ800

Hardware Configuration
IBQ800 Series User’s Manual
11
2
2.1.1 Edge Connector
Pin
Signal Name
Pin
Signal Name
1
Ground
2
Ground
3
GBE_MDI3-
4
GBE_MDI2-
5
GBE_MDI3+
6
GBE_MDI2+
7
GBE_LINK100#
8
GBE_LINK1000#
9
GBE_MDI1-
10
GBE_MDI0-
11
GBE_MDI1+
12
GBE_MDI0+
13
GBE_LINK#
14
GBE_ACT#
15
GBE_CTREF
16
SUS_S5#
17
WAKE#
18
SUS_S3#
19
Reserved
20
PWRBTN#
21
Reserved
22
Reserved
23
Ground
24
Ground
KEY
KEY
25
Ground
26
PWGIN
27
BATLOW#
28
RSTBTN#
29
SATA0_TX+
30
SATA1_TX+
31
SATA0_TX-
32
SATA1_TX-
33
SATA_ACT#
34
Ground
35
SATA0_RX+
36
SATA1_RX+
37
SATA0_RX-
38
SATA1_RX-
39
Ground
40
Ground
41
BIOS_DISABLE#
42
SDIO_CLK#
43
SDIO_CD#
44
Reserved
45
SDIO_CMD
46
SDIO_WP
47
SDIO_PWR#
48
SDIO_DATA1
49
SDIO_DATA0
50
SDIO_DATA3
51
SDIO_DATA2
52
Reserved
53
Reserved
54
Reserved
55
Reserved
56
Reserved
57
Ground
58
Ground
59
HAD_SYNC
60
SMB_CLK
61
HAD_RST#
62
SMB_DAT
63
HAD_BITCLK
64
SMB_ALERT#
65
HAD_SDI
66
GP0_I2C_CLK
67
HAD_SDO
68
GP0_I2C_DAT
69
THRM#
70
WDTRIG#
71
THRMTRIP#
72
WDOUT
73
Ground
74
Ground

12
IBQ800 Series User’s Manual
Pin
Signal Name
Pin
Signal Name
75
U3_USB0_TX_N
76
U3_USB0_RX_N
77
U3_USB0_TX_P
78
U3_USB0_RX_P
79
USB_OC1#
80
USB_OC1#
81
U3_USB2_TX_N
82
U3_USB2_RX_N
83
U3_USB2_TX_P
84
U3_USB2_RX_P
85
USB_OC1#
86
USB_OC0#
87
U2_USB3_N
88
U2_USB2_N
89
U2_USB3_P
90
U2_USB2_P
91
Reserved
92
Reserved
93
U2_USB0_N
94
U2_USB1_N
95
U2_USB0_P
96
U2_USB1_P
97
Ground
98
Ground
99
eDP0_TX0+/LVDS_A0+
100
LVDS_B0+
101
eDP0_TX0-/LVDS_A0-
102
LVDS_B0-
103
eDP0_TX1+/LVDS_A1+
104
LVDS_B1+
105
eDP0_TX1-/LVDS_A1-
106
LVDS_B1-
107
eDP0_TX2+/LVDS_A2+
108
LVDS_B2+
109
eDP0_TX2-/LVDS_A2-
110
LVDS_B2-
111
LVDS_VDD_EN
112
LVDS_BKLT_EN
113
eDP0_TX3+/LVDS_A3+
114
LVDS_B3+
115
eDP0_TX3-/LVDS_A3-
116
LVDS_B3-
117
Ground
118
Ground
119
eDP0_AUX+/LVDS_A_CLK+
120
LVDS_B_CLK+
121
eDP0_AUX-/LVDS_A_CLK-
122
LVDS_B_CLK-
123
LVDS_BKLT_CTRL
124
Reserved
125
LVDS_DDC_DAT
126
eDP0_HPD#
127
LVDS_DDC_CLK
128
Reserved
129
Reserved
130
Reserved
131
DP_LANE3+/TMDS_CLK+
132
U3_USB1_TX_N
133
DP_LANE3-/TMDS_CLK-
134
U3_USB1_TX_P
135
Ground
136
Ground
137
DP_LANE1+/TMDS_LANE1+
138
DP_AUX+
139
DP_LANE1-/TMDS_LANE1-
140
DP_AUX-
141
Ground
142
Ground
143
DP_LANE2+/TMDS_LANE0+
144
U3_USB1_RX_N
145
DP_LANE2-/TMDS_LANE0-
146
U3_USB1_RX_P
147
Ground
148
Ground
149
DP_LANE0+/TMDS_LANE2+
150
HDMI_CTRL_DAT
151
DP_LANE0-/TMDS_LANE2-
152
HDMI_CTRL_CLK
153
DP_HDMI_HPD#
154
DP_HPD#