IBASE Technology IB113 User manual

The information contained in this document has been carefully researched and is, to the best
of our knowledge, accurate. However, we assume no liability for any product failures or
damages, immediate or consequential, resulting from the use of the information provided
herein. Our products are not intended for use in systems in which failures of product could
result in personal injury. All trademarks mentioned herein are property of their respective
owners. All specifications are subject to change without notice.
Manual
IB113
iBASE
Our company network supports you worldwide with offices in Germany, Austria,
Switzerland, Great Britain and the USA. For more information please contact:
FORTEC Elektronik AG
Hauptniederlassung
Lechwiesenstr. 9
86899 Landsberg am Lech
Telefon: [phone]
Telefax: [phone]
E-Mail: [email protected]
Internet: www.fortecag.de
FORTEC Elektronik AG
Büro West
Hohenstaufenring 55
50674 Köln
Telefon: [phone]
Telefax: [phone]
E-Mail: [email protected]
Internet: www.fortecag.de
FORTEC Elektronik AG
Büro Wien
Nuschinggasse 12
A-1230 Wien
Telefon: [phone]
Telefax: [phone]
E-Mail: [email protected]
Internet: www.fortec.at
ALTRAC AG
(Tochter der FORTEC):
Bahnhofstraße 3
CH-5436 Würenlos
Telefon: [phone]
Telefax: [phone]
E-Mail: [email protected]
Internet: www.altrac.ch

www.ibase.com.tw
IBASE Technology Inc.
IB113
Wide Temperature ARM-based SBC with
Freescale i.MX6 Cortex-A9 Dual Core 800MHz SoC
Users Maual
2015 DEC. V1.0c

2
IB113
This page is intentionally left blank.

Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
3
IBASE Technology Inc.
Quick Start Guide
Here is a step-by-step guide to boot up the IB113:
a. Based on the order, the (Android) or (Linux OS) will be preloaded in the
IBs eMMC. “ste a e ooted up ith HDMI  default ad poer
input ready.
b. To use the root/ serial port debug function, please check Chapter 4.2.1 (COM1
debug cable setup) information.
c. To boot up with a different LVDS panel, please refer to Chapter 4.2.2.
d. To make a recovery SD card (for IB113 advanced user only), please refer to
Chapter 4.
Note: different LVDS panels have different customization; please check with your sales
contact.
e. For advanced users who are building their own products, please refer to
Chapter 5.
f. For special HW/SW/ panel customization requests or assistance, please check
with Ibase sales dept.

4
IB113
TABLE OF CONTENTS
This page is intentionally left blank.Quick Start Guide............................................................2
1. Introduction....................................................................................................................6
1.1. IB113 Introduction ..........................................................................................................6
1.2. IB113 Hardware Specifications........................................................................................7
1.3. Optional Items..............................................................................................................10
2. Jumper setting on IB113................................................................................................11
3. Software Setup .............................................................................................................28
3.1. Make a Recovery SD Card (for advanced user only) .......................................................28
3.2. Parameter Setting on U-boot ........................................................................................31
3.2.1. Preparation (debug console) ..................................................................................31
3.2.2. Display setting command For Linux and Android ....................................................32
4. BSP User Guide ( for advanced software engineer only )................................................34
4.1. Building BSP Source ......................................................................................................34
4.1.1. Preparation ...........................................................................................................34
4.1.2. Installing Toolchain................................................................................................34
4.1.3. Building u-boot ......................................................................................................35
4.1.4. Building kernel.......................................................................................................36
4.1.5. Build RAMdisk image (option.)...............................................................................37
4.1.6. Install Linux to SD card...........................................................................................38
4.1.7. Booting with your SD card......................................................................................39
5. Reference Code.............................................................................................................40
5.1. How to use I2C in Linux .................................................................................................40
5.2. How to use GPIO in Linux ..............................................................................................57
5.2.1. GPIO Mapping Table..............................................................................................57
5.2.2. GPIO Sample Code .................................................................................................57
5.3. How to use Watchdog in Linux ......................................................................................58
6. Appendix D –ADB configuration (For Android only) ......................................................61
7. Appendix D –Useful links...............................................................................................64

Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
5
IBASE Technology Inc.
Acknowledgments
FreescaleTM is a trademark of Freescale Semiconductor, Inc.
ARM®Corte™-A9 is a trademark of ARM Holdings, plc.
Android, name, logo, and other Android trademarks are property of Google Inc.
Linux, trademarks or marks include all trade and service marks and logos owned
by the Linux Foundation.
All other product names or trademarks are properties of their respective owners.

6
IB113
1. Introduction
1.1. IB113 Introduction
IB113 is a 3.5" Disk-Size SBC w/ ARM Base Freescale i.MX6 Cortex-A9
800Mhz CPU. IB113 fulfill industrial ambient operating temperature from -40
℃to +85℃. The device offers 3D graphics acceleration, while also supporting
numerous peripherals, including RS232/422/485, CAN, USB, USB OTG, 1st/2nd LAN
ports, SATA, R/C touch interfaces, that are well suited for industrial applications.
All components are selected from industrial grade parts for wide-temperature
environment operation.

Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
7
IBASE Technology Inc.
1.2. IB113 Hardware Specifications
Freescale ARM Cortex-A9, 800MHz, automotive-grade processor
Supports -40°C~ 85°C environment, all industrial-grade components
Supports DC 12V~24V input voltage
1GB DDR3, 4GB eMMC on board
Supports 4/5-wired resistive touch, and I2C/USB header for capacitive touch
Supports OpenGL ES 2.0 and OpenVG 1.1 hardware accelerators
Supports COM, CAN,USB-OTG, SD card, HDMI, Dual Channel LVDS
Supports rich I/O internface for BOM customization
Form Factor
3.5" Disk-Size SBC, 102mm x 147mm
CPU
Freescale Cortex™-A9 i.MX6 Dual 800MHz, automotive grade
CPU
System Memory
1GB DDR3 on board
Data Memory
4GB eMMC on board
SD socket (up to 32GB)
Display
HDMI
Dual CH, 18/24 bit dual channel LVDS (up to 1920 x 1080)
Video Codec
Decode: 1080p, 30fps
Encode: 1080p, 30fps
LAN
1st LAN : 10/100/1000 Base-T Ethernet (Gb LAN)
2nd LAN : 10/100 Base-T Ethernet
Touch
PM6000 resistive touch IC (4/5-wires) on board
USB/ I2C header on board ( for capacitive touch)
Audio
Audio pin header (1x microphone, 1x speaker)
RTC
Seiko RTC IC on board
Watchdog
256 Levels
Edge I/O
1x 1st 10/100/1000 LAN
1x 2nd 10/100 LAN
1x USB 2.0 Host (Type-A)
1x USB OTG (mini-USB Type-B)
1x COM RS-232/422/485
1x SD socket (up to 32GB)
1x DC-in jack
1x HDMI (Type-A)
1x Reset button

8
IB113
Headers & Expansion Slots
Headers:
1x GPIOx8 pin header
1x Debug port pin header
1x USB2.0 Host box header
1x I2C pin header
1x Resistive touch header (4/5-wires)
2x CAN Bus 2.0B ( w/ isolation) pin headers
1x Dual channel LVDS box header (supports full HD)
1x Audio pin header (1x microphone, 1x speaker)
1x SATA header
Slots:
1x Full size Mini PCIe with USB interface
Power
12V~24V DC-in
Operating Temperature
-40°C~ 85°C (-40°F ~ 185°F)
Devices
WiFi / GPS / 3G module (option)
Software Support
Ubuntu Linux 12.04(kernel 3.0.35)/ Android 4.3
Relative Humidity
10%~90% (non-condensing)
Ordering Information
IB113
3.5-inch SBC w/ Industrial-Grade Freescale i.MX6 dual core
(800Mhz), 1GB DDR3, 2x LAN , SD, 1x COM ports, Mini
PCI-E(x1) slot, 2x LVDS HDMI, 8x GPIO, 2x CAN, 2nd LAN,
4GB eMMC, Resistive touch panel (4/5-wires) support
IB113A
3.5-inch SBC w/ Industrial-Grade Freescale i.MX6 solo
core (800Mhz), 1GB DDR3, 1x LAN , SD, 1x COM ports,
Mini PCI-E(x1) slot,2x LVDS, HDMI, 8x GPIO, 4GB
eMMC
Accessary (Optional)
RF:
- 3G+GPS Combo ( Mini PCI-E card)
- WIFI+BT Combo (Mini PCI-E card)
- WIFI module (USB I/F)
- BT module (USB/IF)
Display:
- 800 x 600, resistive touch panel (5-wires)
- LVDS cable: LCD314
Debug cable:
- PK1-100A
( Please contact with iBASE sales)
HSIB113-BGA-A
Heat-sink for IB113
‧ This specification is subject to change without prior notice.
‧ Each thermal solution should be considered by different system design specification.

Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
9
IBASE Technology Inc.
I/O View
Board Dimensions

10
IB113
1.3. Optional Items
If you have any optional item request, please contact Ibase sales dept.
Item
Specifications
Part Number
Remarks
Speaker
4 OHM
1.5W 10CM
A057SPP3516K11000P
Power Supply
60W 12V
A005PS060WFSP0101P
USB OTG ( mini
type) Cable
USB- 81 2- HEAD
4C 120CM
C501USB8105A12000P
DSUB- USB- 4
Cable
TEST- 220
C501TES2200202000P
For internal USB
header
Debug Port Cable
PK1-100A
C501PK11003102A00P
For internal
debug port.

Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
11
IBASE Technology Inc.
2. Jumper setting on IB113
[Important] Please check the jumpers, DIP, buttons and switches on
IB113 before doing the panel connection and boot up.
Jumpers are used on IB113 to select various settings and features according
to your needs and applications. Contact your supplier if you have doubts
about the best configuration for your needs. The following lists the
connectors on IB113 and their respective functions.
Jumper Locations on IB113
Top Side

12
IB113
* IB113 full jumpers and connectors as blue words.
* IB113A (with i.MX6 Solo 800Mhz CPU) has no 2nd LAN (CN8), SATA (CN2, J3), Resisitve touch
conn.(J2), CAN connector on IB113A

Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
13
IBASE Technology Inc.
SW1: System Boot Configuration (factory use only)
SW1
Boot From
10101010
SD
01100110
EMMC
JP9: COM2 RS232, RS422, RS485 Selection
Mode
JP9
RS232
2-4 Short
3-5 Short
RS422
3-5 Short
4-6 Short
RS485
1-3 Short
4-6 Short
Default setting is RS232 mode. JP9 setting for COM2.
JP6: USB +3.3V/+5V Power Setting
2
6
1
5

14
IB113
JP6
Setting
+3.3V
+5V
Default setting is +5V.
JP6 setting for J9.
JP4: LVDS +3.3V/+5V Power Setting
JP4
Setting
+3.3V
+5V
Default setting is +3.3V. ; JP4 setting for CH1,CH2.
3
1
1
3

Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
15
IBASE Technology Inc.
JP3: LED Brightness +5V/+12V Power Setting
JP3
Setting
+5V
+12V
efault setting is +5V.
JP3 setting for CH1,CH2
CN1: SD Card Connector
COM1 PORT: COM1 RS232 Connector
(Debug Port, factory use only)
Part Number: 0195-01-200-040
Description: Pin Header 2.0*2.0mm S/T Single Row 4pin
Pin #
Signal Name
1
COM1 RX, Receive data
2
COM1 TX, Transmit data
3
GND, ground
4
NC
1
3
1 4
4

16
IB113
COM2 : RS232/RS422/RS485 Serial Port
[
Pin #
Signal Name
RS-232
RS-422
RS-485
1
DCD
TX-
DATA-
2
RX
TX+
DATA+
3
TX
RX+
NC
4
DTR
RX-
NC
5
Ground
Ground
Ground
6
DSR
NC
NC
7
RTS
NC
NC
8
CTS
NC
NC
9
NC
NC
NC
Note: Please refer to JP9 setting for RS232, RS422 and RS485 mode selection.
CH1,CH2: LVDS Display Connector
Part Number: DF13-20DP-1.25V(95)
Description: P1.25 SMD 20PIN Male 180D 2R
Signal Name
Pin #
Pin #
Signal Name
LCD1_TX0_P
1
2
LCD1_TX0_N
Ground
3
4
Ground
LCD1_TX1_P
5
6
LCD1_TX1_N
Ground
7
8
LCD_VDD
LCD1_TX3_P
9
10
LCD1_TX3_N
LCD1_TX2_P
11
12
LCD1_TX2_N
Ground
13
14
Ground
LCD1_CLK_P
15
16
LCD1_CLK_N
19
1
20
2

Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
17
IBASE Technology Inc.
BTL_PWM
17
18
LCD_VDD
BKLT_VCC
19
20
BKLT_VCC
J2: Resistive Touch Panel Connector
Part Number: 0110-161-050
Description: MINI BASE;DIP 180D MINI 5PIN
Pin #
Signal Name
1
JTP_LR
2
JTP_LL
3
JTP_WIP
4
JTP_UR
5
JTP_UL
CN7: 100/1Gb LAN1 (From Freescale i.MX6)
CN8: 10/100Mb LAN2 (USB to Ethernet)
5 1
4

18
IB113
CN3,4: LED Backlight Control Connector
Part Number: 0110-2610040
Description: JST-PH Type Wafer 2.0mm 4Pin
Pin #
Signal Name
1
BKLT_VCC
2
LCD_BKLT_EN
3
LCD_BKLT_PWM
4
GND
J7: Speaker Right Out Connector
Part Number: 0110-2610020
Description: Molex 53047 1.25mm Wafer S/T Type 2pin
Pin #
Signal Name
1
SPEAKER_RIGHT-
2
SPEAKER_RIGHT+
Note: The maximun output power is 2 W with 4 Ω speaker
or 1.4 W with 8 Ω speaker
1
21

Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
19
IBASE Technology Inc.
J8: Speaker Left Out Connector
Part Number: 0110-2610020
Description: Molex 53047 1.25mm Wafer S/T Type 2pin
Pin #
Signal Name
1
SPEAKER_LEFT-
2
SPEAKER_LEFT+
Note: The maximun output power is 2 W with 4 Ω speaker
or 1.4 W with 8 Ω speaker
JMIC1: Microphone Connector
Part Number: 0110-2610020
Description: Molex 53047 1.25mm Wafer S/T Type 2pin
Pin #
Signal Name
1
GND
2
MIC_IN
21
21