IBASE Technology MB820 User manual

MB820
Socket 478 Pentium®4
Intel®875P Chipset
Industrial Motherboard
USER’S MANUAL
Version 1.1

ii MB820 User’s Manual
Acknowledgments
Award is a registered trademark of Award Software International,
Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel and Pentium 4 are registered trademarks of Intel
Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Winbond is a registered trademark of Winbond Electronics
Corporation.
All other product names or trademarks are properties of their
respective owners.

MB820 User’s Manual iii
Table of Contents
Introduction.......................................................1
Checklist..............................................................................1
Product Description.............................................................2
Specifications......................................................................3
Board Dimensions...............................................................4
Installations.......................................................5
Installing the CPU...............................................................6
ATX Power Installation ......................................................7
Installing the Memory.........................................................7
Setting the Jumpers .............................................................8
Connectors on MB820 ......................................................13
Watchdog Timer Configuration........................................25
BIOS Setup.......................................................29
Drivers Installation......................................51
Intel 875P Chipset Software Intallation Utility.................52
Realtek AC97 Codec Audio Driver Installation................55
Intel PRO LAN Drivers Installation..................................56
VGA Drivers Installation ..................................................57

iv MB820 User’s Manual
This page is intentionally left blank.

INTRODUCTION
MB820 User’s Manual 1
Introduction
Checklist
Your MB820 Pentium®4 motherboard package should include the items
listed below:
• The MB820 motherboard
• This User’s Manual
• 1 Backplate
• 2 IDE Cable
• 1 Floppy Cable
• 2 SATA Cable
• 1 Dual-Serial-Port Cable
• 1 CD containing the following:
• Chipset Drivers
• Flash Memory Utility

INSTALLATIONS
2MB820 User’s Manual
Product Description
The MB820 Pentium®4 motherboard incorporates the Intel 875P chipset
that can utilize a single PGA478 processor of up to 3.2GHz or higher
and supports FSB frequency of 400/533/800Mhz (100Mhz, 133Mhz,
and 200Mhz HCLK respectively).
The 875P chipset is designed for use with the Pentium®4 processor with
512-KB L2 cache on 0.13 micron process. The integrated MCH
component provides the CPU interface, DDR interface, AGP interface,
Hub Interface and AGP 8X graphics interface.
Four DDR memory sockets supports DDR 400/333/266 SDRAM
DIMM modules of up to 4GB in capacity. ECC is also supported.
The board also comes optional with either integrated 10/100MB LAN
support or an Intel®82547GI Gigabit LAN controller. Two Serial ATA
connectors offer 1.5 Gigabits/sec data throughput speed - faster than the
most advanced parallel ATA.
Expansion is provided by four PCI slots, two ISA slots and one AGP8X
interface. Other advanced features include six USB 2.0 ports, IrDA
interface, PCI to ISA bridge, digital I/O, four serial ports, watchdog
timer and audio function. Dimensions of the board are 12” by 9.5” in an
ATX form factor.

INTRODUCTION
MB820 User’s Manual 3
Specifications
Product Name MB820
CPU Support Intel®Pentium®4
CPU Voltage 0.8375V~1.6V (VRD 10)
System Speed 2.26G~3.2GHz
CPU Operating
Frequency 533MHz / 800MHz
Green /APM APM1.2
CPU Socket Socket 478
Chipset
Intel®875P Chipset MCH: 82875P 1005-pin FC-BGA, ICH5: 82801ER
460-pin MBGA, FWH
BIOS Award BIOS; Supports ACPI
Cache 256K (Celeron) / 512K(Pentium®4) Level 2 cache
VGA SMI 712 2D Graphics Controller (PCI interface)
supports CRT display
Embedded 2MB display memory
AGP port AGP 8X interface
LAN ICH5 integrated LAN controller (10/100Mb) + Phy
82562EZ or one Intel®(1) Gigabit LAN controller
82547EI/GI (CSA port)
Audio ICH5built-in Sound controller + AC97 Codec ALC650
(5.1 channel)
Memory type
Four (4) x DDR sockets; supports 2.5V DDR400/333 SDRAM DIMM module (support dual channel); Max.
capacity - 4GB; supports ECC function
LPC I/O Winbond W83627HF: IrDAx1, LPTx1, COM1
(RS-232), COM2 (RS-232/ RS422/RS485), FDC
2.88MB, Hardware monitoring (3 thermal inputs, 8
voltage monitor inputs, VID0-4, 1 chassis open
detection, 3 fan headers)
RTC/CMOS Built in ICH5
Battery Lithium battery
Keyboard Controller Built in Winbond 83627HF
IDE ICH5 built-in, IDE1, IDE2 (Ultra DMA 33/66/100)
Serial ATA connector Two (2) ports
D-type connectors PS/2 mouse, PS/2 keyboard, VGA (CRT), RJ-45,
Sound, USBx6
Power Connector ATX 12V
Expansion Slots 1 AGP slot, 4 PCI slots, 2 ISA slots
PCI to ISA Bridge Winbond W83628F with W83629D
Secondary Super I/O Winbond 83877 (COM3, COM4 RS-232)
USB Six (6) ports on board, USB 2.0 compliant
Digital I/O 4 In, 4 Out
SSD Interface DiskOnChip socket supports up to 512MB capacity
Watchdog Timer Supports 256 segments (0,1,2…255. sec/min)
System Voltages +5V, +12V, -12V, 5VSB, -5V, 3.3V
Board Size 12” x 9.5” (ATX form factor)
Other Features IrDA interface, Modem Wakeup, LAN Wakeup

INSTALLATIONS
4MB820 User’s Manual
Board Dimensions

INSTALLATIONS
MB820 User’s Manual 5
Installations
This section provides information on how to use the jumpers and
connectors on the MB820 in order to set up a workable system. The
topics covered are:
Installing the CPU...............................................................6
ATX Power Installation ......................................................7
Installing the Memory.........................................................7
Setting the Jumpers .............................................................8
Connectors on MB820 ......................................................13
Watchdog Timer Configuration........................................25

INSTALLATIONS
6MB820 User’s Manual
Installing the CPU
The MB820 motherboard supports a Socket 478 processor socket for
Intel®Pentium®4 processors.
The Socket 478 processor socket comes with a lever to secure the
processor. Raise this lever to about a 90°angle to allow the insertion of
the processor. Place the processor into the socket by making sure the
notch on the corner of the CPU corresponds with the notch on the inside
of the socket. Once the processor has slide into the socket, return the
lever to the lock position. Refer to the figures below.
After you have installed the processor into the socket, check if the
jumpers for the CPU type and speed are correct.
NOTE: Ensure that the CPU heat sink and the CPU top surface are in
total contact to avoid CPU overheating problem that would
cause your system to hang or be unstable.

INSTALLATIONS
MB820 User’s Manual 7
ATX Power Installation
The system power is provided to the motherboard with the ATXP1 and
ATXP2 ATX power connectors. ATXP2 is a 4-pin 12V power
connector. ATXP1 is to be connected to a standard ATX power
connector.
Installing the Memory
The MB820 motherboard supports four DDR memory sockets for a
maximum total memory of 4GB in DDR memory type. You can install
unbuffered & ECC DDR DIMMs. It supports DDR266 when installed
with CPUs that have clock speeds of 400MHz. It supports DDR266/333
when installed with CPUs that have clock speeds of 533MHz. It supports
DDR266/320/400 when installed with CPUs that have clock speeds of
800MHz. The board provides dual channel functionality for its DIMM
slots. DIMM1/2is for one channel and DIMM3/4 is for another channel.
Enabling dual channels can increase data access rates by putting two
similar-size DDR modules into two same-color DIMM slots.
Basically, the system memory interface has the following features:
Supports two 64-bit wide DDR data channels
Available bandwidth up to 3.2GB/s (DDR400) for single-channel
mode and 6.4GB/s (DDR400) in dual-channel mode.
Supports ECC DIMMs.
Supports 128Mb, 256Mb, 512Mb, 1Gb DDR technologies.
Supports only x8, x16, DDR devices with four banks
Registered DIMMs not supported
Supports opportunistic refresh
Up to 16 simultaneously open pages (four per row, four rows
maximum)

INSTALLATIONS
8MB820 User’s Manual
Setting the Jumpers
Jumpers are used on MB820 to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on MB820 and their respective functions.
Jumper Locations on MB820..........................................................9
JP1: RS232/422/485 (COM2) Selection.......................................10
JP2: COM1 RS232 +5V/+12V Power Setting..............................10
JP3: COM2 RS232 +5V/+12V Power Setting..............................10
JP4: Clear CMOS Contents ..........................................................11
JP5: COM3 RS232 +5V/+12V Power Setting..............................11
JP6: COM4 RS232 +5V/+12V Power Setting..............................11
JP7: DiskOnChip Address Select .................................................12
JP8: Onboard VGA Enable/Disable .............................................12

INSTALLATIONS
MB820 User’s Manual 9
Jumper Locations on MB820
Jumper Locations on MB820 ...........................................................Page
JP1: RS232/422/485 (COM2) Selection.............................................. 10
JP2: COM1 RS232 +5V/+12V Power Setting .................................... 10
JP3: COM2 RS232 +5V/+12V Power Setting .................................... 10
JP4: Clear CMOS Contents................................................................. 11
JP5: COM3 RS232 +5V/+12V Power Setting .................................... 11
JP6: COM4 RS232 +5V/+12V Power Setting .................................... 11
JP7: DiskOnChip Address Select........................................................ 12
JP8: Onboard VGA Enable/Disable.................................................... 12

INSTALLATIONS
10 MB820 User’s Manual
JP1: RS232/422/485 (COM2) Selection
COM1 is fixed for RS-232 use only.
J3, COM2 is selectable for RS232, RS-422 and RS-485.
The following table describes the jumper settings for COM2 selection.
COM2
Function RS-232 RS-422 RS-485
Jumper
Setting
(pin closed)
Short:
1-2
9-11
10-12
15-17
16-18
Short:
3-4
7-9
8-10
13-15
14-16
Short:
5-6
7-9
8-10
13-15
14-16
JP2: COM1 RS232 +5V/+12V Power Setting
JP2 Setting Function
Pin 1-2
Short/Closed +12V
Pin 3-4
Short/Closed Normal
Pin 5-6
Short/Closed +5V
JP3: COM2 RS232 +5V/+12V Power Setting
JP3 Setting Function
Pin 1-2
Short/Closed +12V
Pin 3-4
Short/Closed Normal
Pin 5-6
Short/Closed +5V

INSTALLATIONS
MB820 User’s Manual 11
JP4: Clear CMOS Contents
Use JP4, a 3-pin header, to clear the CMOS contents. Note that the
ATX-power connector should be disconnected from the motherboard
before clearing CMOS.
JP4 Setting Function
Pin 1-2
Short/Closed Normal
Pin 2-3
Short/Closed Clear CMOS
JP5: COM3 RS232 +5V/+12V Power Setting
JP5 Setting Function
Pin 1-2
Short/Closed +12V
Pin 3-4
Short/Closed Normal
Pin 5-6
Short/Closed +5V
JP6: COM4 RS232 +5V/+12V Power Setting
JP6 Setting Function
Pin 1-2
Short/Closed +12V
Pin 3-4
Short/Closed Normal
Pin 5-6
Short/Closed +5V

INSTALLATIONS
12 MB820 User’s Manual
JP7: DiskOnChip Address Select
JP7 Address
D0000-D7FFF
D8000-DFFFF (default)
JP8: Onboard VGA Enable/Disable
Use JP8 to enable or disable the onboard VGA controller.
JP8 Setting Onboard VGA
Pin 1-2
Short/Closed Enabled
Pin 2-3
Short/Closed Disabled

INSTALLATIONS
MB820 User’s Manual 13
[
Connectors on MB820
The connectors on MB820 allows you to connect external devices such
as keyboard, floppy disk drives, hard disk drives, printers, etc. The
following table lists the connectors on MB820 and their respective
functions.
Connector Locations on MB820 .................................................. 14
ATXP1: ATX Power Supply Connector...................................... 15
ATXP2: ATX 12V Power Connector .......................................... 15
DIMM1, DIMM2: DDR Channel A Connectors.......................... 15
DIMM3, DIMM4: DDR Channel B Connectors.......................... 15
AGP1: AGP Slot .......................................................................... 15
PCI1, PCI2, PCI3, PCI4: PCI Slots.............................................. 15
SL1, SL2: ISA Slots..................................................................... 15
CN1: PS/2 Keyboard and PS/2 Mouse Connectors...................... 16
CN2: 4-port USB Connector........................................................ 16
CN3, J3: Serial Ports.................................................................... 16
CN4: Parallel Port Connector....................................................... 17
CN6: VGA CRT Connector ......................................................... 17
CN7: USB and LAN RJ45 Connectors........................................ 18
CN8: Audio Connector................................................................. 18
J1: IrDA Connector...................................................................... 18
J4: CD-In Audio Connector ......................................................... 18
J5, J6: Serial ATA (SATA) Connectors....................................... 19
J8, J10: COM3 and COM4 Serial Ports Connector...................... 19
J9: Wake On LAN Connector ...................................................... 19
J11: Digital I/O Connector (4 in, 4 out) ....................................... 20
J12: System Function Connector.................................................. 20
J13: USB Connector..................................................................... 20
FAN1: CPU Fan Power Connector .............................................. 22
FAN2: VGA Fan Power Connector ............................................. 22
FAN3: Chassis Fan Power Connector.......................................... 22
FDD1: Floppy Drive Connector................................................... 23
IDE, IDE2: Primary and Secondary IDE Connectors .................. 24

INSTALLATIONS
14 MB820 User’s Manual
Connector Locations on MB820
Connectors on MB820.......................................................................................................................................Page
ATXP1: ATX Power Supply Connector................................................................................................................15
ATXP2: ATX 12V Power Connector....................................................................................................................15
CN1: PS/2 Keyboard and PS/2 Mouse Connectors...............................................................................................16
CN2: 4-port USB Connector..................................................................................................................................16
CN3, J3: Serial Ports..............................................................................................................................................16
CN4: Parallel Port Connector ................................................................................................................................17
CN6: VGA CRT Connector...................................................................................................................................17
CN7: USB and LAN RJ45 Connectors..................................................................................................................18
CN8: Audio Connector ..........................................................................................................................................18
J1: IrDA Connector................................................................................................................................................18
J4: CD-In Audio Connector...................................................................................................................................18
J5, J6: Serial ATA (SATA) Connectors ................................................................................................................19
J8, J10: COM3 and COM4 Serial Ports Connector...............................................................................................19
J9: Wake On LAN Connector................................................................................................................................19
J11: Digital I/O Connector (4 in, 4 out).................................................................................................................20
J12: System Function Connector...........................................................................................................................20
J13: USB Connector ..............................................................................................................................................20
FAN1: CPU Fan Power Connector........................................................................................................................22
FAN2: VGA Fan Power Connector.......................................................................................................................22
FAN3: Chassis Fan Power Connector ...................................................................................................................22
FDD1: Floppy Drive Connector.............................................................................................................................23
IDE, IDE2: Primary and Secondary IDE Connectors ............................................................................................24

INSTALLATIONS
MB820 User’s Manual 15
ATXP1: ATX Power Supply Connector
ATXP1 is a 20-pin ATX power supply connector. Refer to the following
table for the pin out assignments.
Signal Name Pin # Pin # Signal Name
3.3V 11 1 3.3V
-12V 12 2 3.3V
Ground 13 3 Ground
PS-ON 14 4 +5V
Ground 15 5 Ground
Ground 16 6 +5V
Ground 17 7 Ground
-5V 18 8 Power good
+5V 19 9 5VSB
+5V 20 10 +12V
11 1
20 10
ATXP2: ATX 12V Power Connector
Pin # Signal Name
1 Ground
2 Ground
3 +12V
4 +12V
DIMM1, DIMM2: DDR Channel A Connectors
DIMM1 and DIMM2 are the first DDR channel connectors that must be
use together at one time in order for the system to function properly.
DIMM3, DIMM4: DDR Channel B Connectors
DIMM3 and DIMM4 are the second DDR channel connectors that must
be use together at one time in order for the system to function properly.
AGP1: AGP Slot
PCI1, PCI2, PCI3, PCI4: PCI Slots
SL1, SL2: ISA Slots

INSTALLATIONS
16 MB820 User’s Manual
CN1: PS/2 Keyboard and PS/2 Mouse Connectors
PS/2 Mouse
PS/2 Keyboard
Signal Name Keyboard Mouse Signal Name
Keyboard data 1 1 Mouse data
N.C. 2 2 N.C.
GND 3 3 GND
5V 4 4 5V
Keyboard clock 5 5 Mouse clock
N.C. 6 6 N.C.
CN2: 4-port USB Connector
CN2 is a USB connector consisting of four ports stacked vertically.
Pin Signal Name
1 Ground
2 USB+
3 USB-
CN2 4 Vcc
CN3, J3: Serial Ports
CN3 (COM1) is a DB-9 connector, while J3 is a COM2 pin-header
connector. COM2 is optionally available as a DB-9 connector (CN5).
COM1 COM2
Signal Name Pin # Pin # Signal Name
DCD, Data carrier detect 1 6 DSR, Data set ready
RXD, Receive data 2 7 RTS, Request to send
TXD, Transmit data 3 8 CTS, Clear to send
DTR, Data terminal ready 4 9 RI, Ring indicator
GND, ground 5 10 Not Used