IBASE Technology MB930-R User manual

MB930
(MB930-R, MB930F-R,
MB930GF-R, MB930RF-R)
Socket LGA775
Intel®Q35 Chipset
Industrial Motherboard
USER’S MANUAL
Version 1.0

Acknowledgments
Award is a registered trademark of Award Software International,
Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel are registered trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Winbond is a registered trademark of Winbond Electronics
Corporation.
All other product names or trademarks are properties of their
respective owners.

MB930-R User’s Manual iii
Table of Contents
Introduction .......................................................1
Checklist..............................................................................1
Product Description............................................................. 1
Specifications ......................................................................3
Board Dimensions ............................................................... 4
Installations .......................................................5
Installing the CPU ...............................................................6
ATX Power Installation ......................................................7
Installing the Memory ......................................................... 8
Setting the Jumpers .............................................................9
Connectors on MB930-R .................................................. 14
Watchdog Timer Configuration ........................................28
BIOS Setup.......................................................33
Drivers Installation ......................................55
Intel Q35 Chipset Software Installation Utility.................56
Intel Q35 Chipset Graphics Driver....................................58
Realtek HAD Codec Audio Driver Installation ................59
Intel LAN Drivers Installation .......................................... 60
Appendix ...........................................................63
A. I/O Port Address Map................................................... 63
B. Interrupt Request Lines (IRQ)...................................... 64

iv MB930-R User’s Manual
Ordering Information:
Model ICH SATA Intel LANPHY PCI-E
Gigabit LAN
Remarks
Remarks
MB930-R ICH9 4 82562V/ 10/100 N/A
MB930F-R ICH9 4 82566DM(1G) PCI-E GbE
(ME88E8053)
MB930GF-R ICH9 4 82566DM(1G) PCI-E GbE
(ME88E8053)
PCB
thickness:
2.5mm;
other specs
same as
MB930F-R
MB930RF-R
(with MOQ)
ICH9R
(RAID)
6 82566DM/(1G) PCI-E GbE
(ME88E8053)

INTRODUCTION
MB930-R User’s Manual 1
Introduction
Checklist
Your MB930-R/MB930F-R/MB930RF-R motherboard package should
include the items listed below:
• The MB930-R/MB930F-R/MB930RF-R motherboard
• This User’s manual
• 1 Back I/O shield
• 1 IDE cable
• 1 Floppy cable
• 1 SATA cable
• 1 Serial-Port cable
• 1 CD containing the following:
• Chipset Drivers
• Flash Memory Utility
Reminder:
About IDE
The IDE connector on board does not support OS installation in hard
drive. A system hard drive connected to this IDE cannot be booted up to
OS.
About SATA
When using a legacy operating system, only one SATA controller is
available that supports SATA port 0 – 3 (CN8, CN9, CN10, CN11). It is
suggested that the legacy operating system is installed using any of these
ports.

INTRODUCTION
2MB930-R User’s Manual
Product Description
The MB930 LGA 775 motherboard incorporates the Intel Q35 chipset
that can utilize a single LGA775 processor of up to 4.0GHz or higher
and supports FSB frequency of 800/1066MHz/1333MHz
(200MHz(800MT/s) and 266MHz(1066MT/s), 333MHz(1333MT/s)
HCLK respectively.
The Q35 chipset is designed for use with the Core.2 processor family,
including a faster 1333 MHz system bus. The integrated GMCH
component provides the CPU interface, DDR2 interface, Hub Interface
and PCI Express graphics interface.
Four DDR2 memory sockets support DDR2 667/800 SDRAM DIMM
modules of up to 8GB in capacity.
The board is designed with one Intel 82566DM PCI Express Gigabit
PHY (MB930RF-R/MB930F-R) or 82562V 10/100 PHY (MB930-R
only) LAN controllers. Serial-II ATA connectors offer 3Gb/s data
throughput speed - faster than the most advanced parallel ATA.
Expansion includes four PCI slots, one PCI Express x1 and one PCI
Express x16 and one ISA slot. Other advanced features include ten USB
2.0 ports, IrDA interface, digital I/O, four serial ports, watchdog timer
and audio function. Dimensions of the board are 12” by 9.5” in an ATX
form factor.
Remarks:
MB930-R/MB930F-R/MB930RF-R supports Intel Supports the Intel
Core 2 Duo and Intel Core 2 Quad processors, and Intel Celeron
400(Conroe-L) Sequence processor.
MB930RF-R supports six Serial ATA connectors (with RAID function).
MB930-R / MB930F-R / MB930GF-R supports four Serial ATA
connectors only. MB930GF-R has the same specifications as
MB930F-R, except that its PCB thickness is 2.4mm).
The IDE connector on board does not support OS installation in hard
drive. A system hard drive connected to this IDE cannot be booted up to
OS.

INTRODUCTION
MB930-R User’s Manual 3
Specifications
Product Name MB930-R/MB930F-R/MB930RF-R
CPU Support Socket LGA775, Supports the Intel Core 2 Duo and Intel
Core2 Quad processors, and Intel Celeron 400 (Conroe-L)
Sequence processor.
CPU Voltage 0.5V~1.6V (VRD 11.0)
System Speed Up to 3.8GHz+
CPU FSB 800MHz/1066MHz /1333MHz
Green /APM APM1.2
CPU Socket LGA 775
Chipset
Intel®Bearlake Chipset
Q35+ICH9 for MB930-R and MB930F-R
Q35+ICH9R for MB930RF-R only
BIOS Award BIOS; supports ACPI
VGA Q35 built-in, supports CRT
LAN1 LAN1: Dual footprint support option
*Intel 82566DM PCI Express Gigabit for MB930F-R and
MB930RF-R
*Intel 82562V PHY 10/100 for MB930-R only
LAN2 Marvell PCI Express Gigabit for MB930F-R and
MB930RF-R
Audio ICH9/ICH9R Built-in audio + HDA codec
Memory type Support Dual Channel
DDR2 DIMM Module x 4, 667/800MHz
(Without ECC function), Max. 8GB
LPC I/O W83627EHG: IrDA x1, Parallel x1, COM1 (RS232), COM2
(RS232/422/485), FDCx1, Hardware monitoring
RTC/CMOS Built in ICH9/ICH9R
Battery Lithium battery
Keyboard Controller Built-in Winbond 83627EHG
PATA JMicro JMB368 PCI-E to PATA controller for one PATA
channel support
One PATA :
IDE connectorx1 +Compact Flash socket Type II x1
IDE1(40pin/2.5mm)supports Ultra DMA 33/66/100
compact Flash (use IDE or CF at a time only)
SATA2 connector MB930-R,MB930F-R supports 4x SATA2 (300MB/s)
MB930RF-R supports 6x SATA2 with RAID function
D-type connectors PS/2 mouse, PS/2 KB, VGA (CRT), RJ-45, Sound, USB x 4
Power Connector ATX 24-pin
Expansion Slots 1 x (PCI Express x16) slot, 1 x (PCI Express x1) slot
4 x PCI slots, 1 x ISA slots (slave only), cannot support ISA
master and DMA access function
PCI to ISA Bridge Winbond W83628F with W83629D
Secondary Super I/O Fintek F81216, supports COM3, COM4 (RS232)
USB ICH9 built in USB Version 2.0, support 8 ports (D-type
connector x 4 port & pin header x 4 port)
Digital I/O 4 In, 4 Out
Watchdog Timer Supports 256 segments (0,1,2…255. Sec/min)
System Voltages +5V, +12V, -12V, 5VSB, -5V, 3.3V
Board Size 12” x 9.5” (ATX form factor)
Other Features IrDA interface, Modem Wakeup,
Dimensions 305mm x 244mm (12“ x 9.6“)

INTRODUCTION
4MB930-R User’s Manual
Board Dimensions

INSTALLATIONS
MB930-R User’s Manual 5
Installations
This section provides information on how to use the jumpers and
connectors on the MB930-R/MB930F-R/MB930RF-R in order to set up
a workable system. The topics covered are:
Installing the CPU........................................................................ 6
ATX Power Installation ............................................................... 7
Installing the Memory.................................................................. 8
Setting the Jumpers ...................................................................... 9
Connectors on MB930-R ........................................................... 14
Watchdog Timer Configuration................................................. 28
Reminder:
The IDE connector on board does not support OS installation in hard
drive. A system hard drive connected to this IDE cannot be booted up to
OS.

INSTALLATIONS
6MB930-R User’s Manual
Installing the CPU
The MB930-R/MB930F-R/MB930RF-R motherboard support an LGA
775 processor socket for Intel Core 2 Duo and Intel Core2 Quad
processors, and Intel Celeron 400(Conroe-L) Sequence processor.
The LGA 775 processor socket comes with a lever to secure the
processor. Refer to the pictures below, from left to right, on how to place
the processor into the CPU socket. Please note that the cover of the
LGA775 socket must always be installed during transport to avoid
damage to the socket.

INSTALLATIONS
MB930-R User’s Manual 7
ATX Power Installation
The system power is provided to the motherboard with the ATX1 and
ATX_12V power connectors. ATX1 is a 24-pin power connector and
ATX_12V is a 8-pin 12V power connector.
The 24-pin power connector can to be connected to a standard 20-pin
ATX power connector in a standard ATX power supply (Min. 400watt).
Note: The power supply 5VSB voltage must be at least 2A.

INSTALLATIONS
8MB930-R User’s Manual
Installing the Memory
The MB930-R/MB930F-R/MB930RF-R motherboard support four
DDR2 memory sockets for a maximum total memory of 8GB in DDR
memory type. It supports DDR2 667/800.
Basically, the system memory interface has the following features:
Supports two 64-bit wide DDR data channels
Available bandwidth up to 6.4GB/s (DDR2 800) for single-channel
mode and 12.8GB/s (DDR2 800) in dual-channel mode.
Supports 256Mb, 512Mb, 1Gb DDR2 technologies.
Supports only x8, x16, DDR2 devices with four banks
Supports only unbuffered DIMMs
Supports opportunistic refresh
Up to 32 simultaneously open pages (four per row, four rows
maximum)
Dual Channel Memory Configuration
If you want to operate the Dual Channel Technology, please note the
following explanations due to the limitation of Intel chipset
specifications.
1. Dual Channel mode will not be enabled if only one DDR II memory
module is installed.
2. To enable Dual Channel mode with two or four memory modules (it is
recommended to use memory modules of identical brand, size, chips,
and speed), you must install them into DIMM sockets of the same color.
The following is a Dual Channel Memory configuration table:
(DS: Double Side, SS: Single Side)
DDRII1 DDRII2 DDRII3 DDRII4
2MemoryModules DS/SS X DS/SS X
X DS/SS X DS/SS
4MemoryModules DS/SS DS/SS DS/SS DS/SS

INSTALLATIONS
MB930-R User’s Manual 9
Setting the Jumpers
Jumpers are used on MB930-R/MB930F-R/MB930RF-R to select
various settings and features according to your needs and applications.
Contact your supplier if you have doubts about the best configuration for
your needs. The following lists the connectors on
MB930-R/MB930F-R/MB930RF-R and their respective functions.
JP1: COM1 RS232 +5V/+12V Power Setting .................................... 11
JP2: RS232/422/485 (COM2) Selection.............................................. 11
JP3: COM2 RS232 +5V/+12V Power Setting .................................... 11
JP4: Clear CMOS Contents ................................................................. 12
JP5: Configure and Recovery (Factory use only)................................ 12
JP8: ME (Management Engine) – Disabled / pin closed..................... 12
JP9: COM4 RS232 +5V/+12V Power Setting .................................... 12
JP10: Compact Flash Socket Master/Slave Setting ............................. 13
JP12: COM3 RS232 +5V/+12V Power Setting .................................. 13

INSTALLATIONS
10 MB930-R User’s Manual
Jumper Locations............................................................................. Page
JP1: COM1 RS232 +5V/+12V Power Setting..................................... 11
JP2: RS232/422/485 (COM2) Selection.............................................. 11
JP3: COM2 RS232 +5V/+12V Power Setting..................................... 11
JP4: Clear CMOS Contents ................................................................. 12
JP5: Configure and Recovery (Factory use only) ................................ 12
JP8: ME (Management Engine) – Disabled / pin closed ..................... 12
JP9: COM4 RS232 +5V/+12V Power Setting..................................... 12
JP10: Compact Flash Socket Master/Slave Setting ............................. 13
JP12: COM3 RS232 +5V/+12V Power Setting................................... 13

INSTALLATIONS
MB930-R User’s Manual 11
JP1: COM1 RS232 +5V/+12V Power Setting
JP1 Setting Function
Pin 1-2
Short/Closed +12V
Pin 3-4
Short/Closed Normal
Pin 5-6
Short/Closed +5V
JP2: RS232/422/485 (COM2) Selection
COM1 is fixed for RS-232 use only.
JP2, COM2 is selectable for RS232, RS-422 and RS-485.
The following table describes the jumper settings for COM2 selection.
COM2
Function RS-232 RS-422 RS-485
Jumper
Setting
(pin closed)
Short:
1-2
9-11
10-12
15-17
16-18
Short:
3-4
7-9
8-10
13-15
14-16
Short:
5-6
7-9
8-10
13-15
14-16
Note: Factory is default RS-232
JP3: COM2 RS232 +5V/+12V Power Setting
JP3 Setting Function
Pin 1-2
Short/Closed +12V
Pin 3-4
Short/Closed Normal
Pin 5-6
Short/Closed +5V

INSTALLATIONS
12 MB930-R User’s Manual
JP4: Clear CMOS Contents
Use JP4, a 3-pin header, to clear the CMOS contents. Note that the
ATX-power connector should be disconnected from the motherboard
before clearing CMOS.
JP4 Setting Function
Pin 1-2
Short/Closed Normal
Pin 2-3
Short/Closed Clear CMOS
JP5: Configure and Recovery (Factory use only)
JP5 Setting Function
Pin 1-2
Short/Closed Normal (default)
Pin 2-3
Short/Closed Configure
Open
Recovery
JP8: ME (Management Engine) – Disabled / pin closed
The factory default setting of the 2-pin JP8 jumper is closed. This means
the management engine function is disabled.
JP9: COM4 RS232 +5V/+12V Power Setting
JP9 Setting Function
Pin 1-2
Short/Closed +12V
Pin 3-4
Short/Closed Normal
Pin 5-6
Short/Closed +5V

INSTALLATIONS
MB930-R User’s Manual 13
JP10: Compact Flash Socket Master/Slave Setting
JP10 Compact Flash
Master
Slave
JP12: COM3 RS232 +5V/+12V Power Setting
JP12 Setting Function
Pin 1-2
Short/Closed +12V
Pin 3-4
Short/Closed Normal
Pin 5-6
Short/Closed +5V

INSTALLATIONS
14 MB930-R User’s Manual
Connectors on MB930-R
The connectors on MB930-R/MB930F-R/MB930RF-R allow you to
connect external devices such as keyboard, floppy disk drives, hard disk
drives, printers, etc.
ATX1: 24-pin ATX Power Connector................................................. 16
ATX_12V1: ATX 12V Power Connector ........................................... 16
DIMM1,2: Channel A DDR2 Socket .................................................. 17
DIMM3,4 Channel B DDR2 Socket.................................................... 17
CN1: PS/2 Keyboard and PS/2 Mouse Connectors ............................. 17
CN2: Serial Ports(COM1) ................................................................... 17
CN3: Parallel Port Connector .............................................................. 18
CN4: VGA CRT Connector................................................................. 18
CN5: HD Audio Connector ................................................................. 19
CN6: 10/100 RJ-45&USB 0/1 Connector (MB930-R)........................ 19
CN6: GbE RJ-45 &USB 0/1 (MB930F-R/MB930RF-R).................... 19
CN7: USB2/3 Connector (MB930-R) ................................................. 19
CN7: Marvell GbE RJ-45&USB2/3 (MB930F-R/MB930RF-R) ........ 20
CN8, CN9, CN10, CN11, CN12,CN13 SATA Connector .................. 20
CN14: Compact Flash TYPE II Socket ............................................... 20
J1: Digital I/O Connector (4 in, 4 out)................................................. 20
J2: COM2 Serial Port........................................................................... 21
J3: IrDA Connector.............................................................................. 21
J4: SPI Debug Tools Port (Factory use only) ............................................ 21
J5: Audio Front Header ....................................................................... 21
J6: USB6/USB7 Connector ................................................................. 22
J7: USB4/USB5 Connector ................................................................. 22
J8, J10: COM3, COM4 Serial Ports(RS232)....................................... 22
J9: CD-In Audio Connector................................................................. 22
J11: Wake On LAN Connector............................................................ 23
J12: System Function Connector ......................................................... 23
J13: ISA Slot........................................................................................ 25
JP11: SPDIFI/ SPDIFO Connector (Reserved) ................................... 25
IDE1: Primary IDE Connectors........................................................... 25
CPU_FAN1: CPU Fan Power Connector........................................... 26
SYS_FAN1: system Fan1 Power Connector ...................................... 26
SYS_FAN2: SYSTEM Fan2 Power Connector ................................. 26
FDD1: Floppy Drive Connector .......................................................... 26
PCIE_1: x16 PCI Express Slot ............................................................ 27
PCIE_2: x1 PCI Express Slots............................................................. 27
PCI1, PCI2, PCI3, PCI4: PCI Slots ..................................................... 27

INSTALLATIONS
MB930-R User’s Manual 15
Connectors on MB930-R/MB930-RF
ATX1: 24-pin ATX Power Connector
ATX_12V1: ATX 12V Power Connector
DIMM1,2: Channel A DDR2 Socket
DIMM3,4 Channel B DDR2 Socket
CN1: PS/2 Keyboard and PS/2 Mouse
CN2: Serial Ports(COM1)
CN3: Parallel Port Connector
CN4: VGA CRT Connector
CN5: HD Audio Connector
CN6: 10/100 RJ-45&USB 0/1 (MB930-R)
CN6: GbE RJ-45 &USB 0/1
(MB930F-R/MB930RF-R)
CN7: USB2/3 Connector (MB930-R)
CN7: GbE RJ-45&USB2/3
(MB930F-R/MB930RF-R)
CN8, CN9, CN10, CN11, CN12,CN13 SATA
CN14: Compact Flash TYPE II Socket
J1: Digital I/O Connector (4 in, 4 out)
J2: COM2 Serial Port
J3: IrDA Connector
J4: SPI Debug Tools Port (Factory use only)
J5: Audio Front Header
J6: USB6/USB7 Connector
J7: USB4/USB5 Connector
J8, J10: COM3, COM4 Serial Ports(RS232)
J9: CD-In Audio Connector
J11: Wake On LAN Connector
J12: System Function Connector
J13: ISA Slot
JP11: SPDIFI/ SPDIFO Connector (Reserved)
IDE1: Primary IDE Connectors
CPU_FAN1: CPU Fan Power Connector
SYS_FAN1: system Fan1 Power Connector
SYS_FAN2: SYSTEM Fan2 Power Connector
FDD1: Floppy Drive Connector
PCIE_1: x16 PCI Express Slot
PCIE_2: x1 PCI Express Slots
PCI1, PCI2, PCI3, PCI4: PCI Slots
LED1: DRAM POWER LED Indicator

INSTALLATIONS
16 MB930-R User’s Manual
MB930-R Edge Connectors
MB930F-R/MB930RF-R/MB930GF-R Edge Connectors
ATX1: 24-pin ATX Power Connector
Signal Name Pin # Pin # Signal Name
3.3V 13 1 3.3V
-12V 14 2 3.3V
Ground 15 3 Ground
PS-ON 16 4 +5V
Ground 17 5 Ground
Ground 18 6 +5V
Ground 19 7 Ground
-5V 20 8 Power good
+5V 21 9 5VSB
+5V 22 10 +12V
+5V 23 11 +12V
Ground 24 12 +3.3V
ATX_12V1: ATX 12V Power Connector
Signal Name Pin # Pin # Signal Name
+12V 5 1 Ground
+12V 6 2 Ground
+12V 7 3 Ground
+12V 8 4 Ground