IBASE Technology MI808 User manual

MI808
Mini-ITX Motherboard
USER’S MANUAL
Version 1.0

ii MI808 User’s Manual
Acknowledgments
Award is a registered trademark of Award Software International,
Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Winbond is a registered trademark of Winbond Electronics
Corporation.
All other product names or trademarks are properties of their
respective owners.

MI808 User’s Manual iii
Table of Contents
Introduction...................................................... 1
Product Description............................................................1
Checklist.............................................................................2
MI808 Specifications .........................................................3
Board Dimensions..............................................................5
Installations...................................................... 6
Installing the Memory.........................................................7
Setting the Jumpers.............................................................8
Connectors on MI808.......................................................15
BIOS Setup.......................................................33
Drivers Installation......................................51
Intel Chipset Software Installation Utility.........................52
VGA Drivers Installation..................................................55
Realtek HD Audio Driver Installation ..............................57
LAN Drivers Installation..................................................58
TXE Drivers Installation...................................................61
Appendix...........................................................63
A. I/O Port Address Map..................................................63
B. Interrupt Request Lines (IRQ)......................................64
C. Watchdog Timer Configuration...................................65

iv MI808 User’s Manual
This page is intentionally left blank.

INTRODUCTION
MI808 User’s Manual 1
Introduction
Product Description
MI808 is a Mini ITX board (170mm x 170mm) that comes with the Intel
Intel® Pentium ® N3000 series processor. It has two DDR3L SO-DIMM
sockets supporting up to 8GB of system memory.
It also features the Intel® Gen8-LP graphics engine with interface for
CRT, DVI-D and 24-bit dual channel LVDS displays.
The platform provides four USB 3.0 connector at the board edge and
USB 2.0 two ports with pin header. Two SATA III ports are included.
MI808 FEATURES
-Mini ITX form factor, 170mm x 170mm
-Onboard Intel® Pentium ® N3000 series
-Two DDR3L SO-DIMM sockets, DDR3L-1600, Max. 8GB
-Intel® Gen8-LP graphics for CRT, DVI-D interface
-24-bit dual channel LVDS interface
-Dual Intel I211-AT PCIe Gigabit LAN
-4x USB 3.0 on edge, 2xUSB 2.0 support
-Two SATA III, 4x COM ports
-Digital I/O 4-in / 4-out, PCIe (1x) slot, 2x Mini-PCIe
-Watchdog Timer, iSMART, RoHS compliance

INTRODUCTION
2 MI808 User’s Manual
Checklist
Your MI808 package should include the items listed below.
•The MI808 Mini-ITX motherboard
•This User’s Manual
•1 CD containing chipset drivers and flash memory utility
•Serial ATA cable
•I/O shield

INTRODUCTION
MI808 User’s Manual 3
MI808 Specifications
Product Name
MI808F-370 (N3700 onboard, DC-in 12V only)
MI808FW-370 (N3700 onboard DC-in 18V~24V, wider range)
MI808F-300(N3000 onboard DC-in 12V only)
MI808FW-300 (N3000 onboard DC-in 18V~24V, wider range)
MI808FW-370A(N3700 onboard DC-in 18V~24V, Non-TPM/CFast)
[Default silk screen model # on PCB is MI808F]
Form Factor
Mini-ITX
SoC Type/Speed
14nm Lithography, FCBGA1170, Package= 25mm x 27mm
-Pentium® N3700 QC, up to 2.4Ghz , TDP=6W
-Celeron® N3000 DC, up to 2.08GHz, TDP=3W
BIOS
AMI BIOS
Memory
2 xDDR3L SO-DIMM socket [Horizontal type]
Maximum to DDR3L-1600@8GB (Non-ECC, Unbuffered, 1.35V)
Display
Intel® Pentium® SoC integrated Gen 8-LP graphics core
Supports DX11.1 & OpenGL 4.2, 3 x independent displays
-VGA x 1(Thru NXP PTN3392) **Supports up
to1920x1200 @ 60Hz*
-LVDS: 24-bit dual channel via NXP PTN3460 thru eDP
**Supports up to1920x1200 @ 60Hz**
-DVI-D x1 **Supports up to 3840x2160 @ 60 Hz**
LAN
Intel I211-AT PCIe Gigabit LAN x 2 **Reserved for external
EEPROM**
USB
Intel® Braswell SoC built-in USB 3.0 host controller, supports 4 ports
-Edge I/O x 4
Intel® Braswell SoC built-in USB 2.0 host controller with USB hub
Renesas uPD720115K8-611-BAK-A(C013720115K861000P)
For total 4 ports x USB 2.0
-2 ports thru pin header
-2 ports thru Mini PCIe slot
Serial ATA Ports
Intel® Braswell SoC built-in SATA III controller, supports 2 ports
-2 x SATAIII connector
-MSATA (thru Mini PCIe) via switch
-CFast (Optional) via switch
Audio
Realtek ALC269QHD-VC3with class-D speaker amplifier (2W per
channel)
Support 2-channel audio out + AMP
LPC I/O
Fintek F81846AD-I [128-pin LQFP, 14x14x1.4mm]
COM #1 (RS232/422/485) supports ring-in with power @500mA
(selectable for 5V or 12V)
-[SP339EER1 232/422/485 transceiver x 1 for jumper-less]
-COM #2 (RS232 only), support ring-in with power @500mA
(selectable for 5V or 12V), with SP3243EBER
-COM #3~COM #4 (RS232 only) with SP3243EBER
[Hardware Monitor]
2 x Thermal inputs; 2 x Voltage monitoring
1 x 4-pin for CPU fan (PWM), 1 x 3-pin for SYS fan (DC mode)
Digital IO
4-in / 4-out (User configurable)
Expansion Slots
PCIe (1x) slot x 1
Full-sized Mini-PCIe x 2[Mounting holes for full-sized (x2) +
half-sized (x1)]
Mini-PCIe #1 supports PCIe(1x) / USB signal
Mini-PCIe #2 supports mSATA / USB signal
CFast x 1 @ solder side [Except MI808FW-370A]

INTRODUCTION
4 MI808 User’s Manual
Edge Connector
(The same as
MI802)
PS/2 Keyboard + PS/2 mouse stack connector x 1
Dual DB9 Stack connector x1 for COM#1 / COM#2
VGA+ DVI-D stack connector x 1 for CRT + DVI-D
RJ45+Dual USB 3.0 stack connector x 2
Audio 3-port connector x 1 (Line-out, Line-in, MIC)
Onboard
Header/Connector
DF11-8 pin connector x 1 for USB (2.0) x 2 ports
2x6 pin header x 1 for front audio (2.54 pitch type)
2x13 pin box header x 1 for LPT
DF11-10 pin box header x 4 for COM #3~# 6
DF20 socket connector x 2 for 24-bit dual channel LVDS
4 pins box header x1 for LCD backlight control
SATA connector x 2 for SATA III device (Blue color)
4-pin power connector x 2 for SATA device
2x5 pin header x 1 for Digital I/O (2.54 pitch type)
4-pin header for speaker out (from ALC269 internal amplifier)
2x4 pin header x 1 for front I/O panel (2.54 pitch type)
2 x 2 pin connector x 1 for power-in
SIM slot x 1 (Location under #1 MiniPCIe)
Watchdog Timer
Yes (256 segments, 0, 1, 2…255 sec/min)
Power Connector
+12V only (
±5
% tolerance) or 18V~+24V
Others
1. iSMART 3.2
2. TPM 2.0 (Infineon SLB9665) [Except MI808FW-370A]
3. Heatsink for fanless solution
OS supporting
- Windows 8.1 (64-bit)
- Window Embedded 8
- Windows 7 (64-bit)
- Linux (Fedora, uBuntu)
RoHS
Yes
Certification
CE /FCC/LVD
Environment
Operation Temperature: 0~60 degree C
Storage Temperature: -40 ~ 80 degree C
Relative humidity: 90%, non-condensing @ 60 degree C
Board Size
170mm x 170mm

INTRODUCTION
MI808 User’s Manual 5
[
Board Dimensions

INSTALLATIONS
6 MI808 User’s Manual
Installations
This section provides information on how to use the jumpers and
connectors on the MI808 in order to set up a workable system. The topics
covered are:
Installing the Memory.......................................................................... 7
Setting the Jumpers..............................................................................8
Connectors on MI808........................................................................ 15

INSTALLATIONS
MI808 User’s Manual 7
Installing the Memory
The MI808 board supports two DDR3L-1600 memory slots.
Remarks:
MI808 supports two SO-DIMM (w/o ECC) modules. Total maximum
memory supported is 8GB.
Installing and Removing Memory Modules
To install the DDR3L modules, locate the memory slot on the board and
perform the following steps:
1. Hold the DDR3L module so that the keyof the DDR3L module aligned
with that on the memory slot.
2. Gently push the DDR3L module in an upright position until the clips of
the slot close to hold the DDR3L module in place when the DDR3L
module touches the bottom of the slot.
To remove the DDR3L module, press the clips with both hands.

INSTALLATIONS
8 MI808 User’s Manual
Setting the Jumpers
Jumpers are used on MI808 to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on MI808 and their respective functions.
Jumper Locations on MI808................................................................9
JP1: LCD Backlight Connector.......................................................... 10
JP2: LVDS Panel Brightness Control Selection.................................. 10
JP3/JP4 COM1/COM2 RS232 RI/+5V/+12V Power Setting ............. 11
JP8: Clear CMOS Contents ............................................................... 11
JP7: Clear ME Contents .................................................................... 13
JP9: For SPI Debug Tools................................................................. 13
J22: ATX/AT Mode .......................................................................... 13

INSTALLATIONS
MI808 User’s Manual 9
Jumper Locations on MI808
Jumpers on MI808..........................................................................Page
JP1: LCD Backlight Connector..........................................................10
JP2: LVDS Panel Brightness Control Selection..................................10
JP3/JP4 COM1/COM2 RS232 RI/+5V/+12V Power Setting..............11
JP8: Clear CMOS Contents................................................................11
JP7: Clear ME Contents.....................................................................13
JP9: For SPI Debug Tools .................................................................13
J22: ATX/AT Mode ..........................................................................13

INSTALLATIONS
10 MI808 User’s Manual
JP1: LCD Backlight Connector
Pin #
Signal Name
1
+12V
2
Backlight Enable
3
Brightness Control
4
Ground
JP2: LVDS Panel Brightness Control Selection
Setting
Brightness Control
(PWM mode)
Open 3.3V
Close 5V(Default)
1
4

INSTALLATIONS
MI808 User’s Manual 11
JP3/JP4 COM1/COM2 RS232 RI/+5V/+12V Power Setting
JP3/JP4 Setting Function
Pin 1-3
Short/Closed
+12V
Pin 3-4
Short/Closed
RI
Pin 3-5
Short/Closed
+5V
JP8: Clear CMOS Contents
JP8 Setting Function
Pin 1-2
Short/Closed Normal
51
62
1
3

INSTALLATIONS
12 MI808 User’s Manual
Pin 2-3
Short/Closed Clear CMOS

INSTALLATIONS
MI808 User’s Manual 13
JP7: Clear ME Contents
JP7 Setting Function
Pin 1-2
Short/Closed Normal
Pin 2-3
Short/Closed Clear ME REGISTER
JP9: For SPI Debug Tools
J22: ATX/AT Mode
1
3

INSTALLATIONS
14 MI808 User’s Manual
Setting
Function
Open
ATX (Default)
Close
AT

INSTALLATIONS
MI808 User’s Manual 15
Connectors on MI808
Connector Locations on MI808 .........................................................16
CN1 / CN2: SATA3 Connectors........................................................17
CN2 Share with CN9.........................................................................17
CN3: PS2 Keyboard/Mouse...............................................................17
CN4: COM1 / COM2 ........................................................................17
CN5: CRT+DVI Connector...............................................................18
CN6/CN7: Gigabit LAN / USB 3.0 Connector...................................18
CN8: Audio Connector......................................................................18
CN9: CFAST Connector....................................................................18
J1, J2: LVDS Connectors, Hirose DF20G-20DP-1V..........................20
J2: First Channel LVDS.....................................................................20
J3: LVDS Panel Power Selection.......................................................20
J4 / J5: SATA HDD Power Connectors .............................................21
J6: DC_IN Connector........................................................................23
J8 / J9: Mini PCIE Slot (SIM Card) ...................................................23
J8 mSATA only (Share with CN1, W/O USB)...................................23
F_USB1: USB 2.0.............................................................................23
J10: DDR3L SO-DIMM (CH-A) Sockets..........................................24
J13: DDR3L SO-DIMM (CH-B) Sockets ..........................................24
J11: MCU JTAG ...............................................................................25
J12: Front Panel.................................................................................25
J15 Amplifier Connector ....................................................................27
J16 Audio Connector (DF11-12DP-2DSA)........................................27
J17: Digital I/O..................................................................................28
J18, J19: COM3/COM4.....................................................................28
CPU_FAN1: CPU Fan Power Connector...........................................30
SYS_FAN1: System Fan1 Power Connector......................................30
J7: SIM Card Slot..............................................................................30
JP5/JP6: Reserved .............................................................................31
J14: LPT Port Connector...................................................................31

INSTALLATIONS
16 MI808 User’s Manual
Connector Locations on MI808
Connector Locations on MI808