IBASE Technology MI980 User manual

MI980
Intel ®4th Generation Core / QM87 PCH
Mini ITX Motherboard
USER’S MANUAL
Version 1.0

ii MI980 User’s Manual
Acknowledgments
AMI is a registered trademark of American Megatrends Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel and Intel® 4th Generation Core DC/QC Processor are
registered trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Fintek is a registered trademark of Fintek Electronics
Corporation.
All other product names or trademarks are properties of their
respective owners.

MI980 User’s Manual iii
Table of Contents
Introduction...................................................... 1
Product Description............................................................1
Checklist.............................................................................1
MI980 Specifications .........................................................2
Board Dimensions..............................................................4
Installations...................................................... 5
Installing the Memory.........................................................6
Setting the Jumpers.............................................................7
Connectors on MI980.......................................................12
BIOS Setup.......................................................25
Drivers Installation......................................52
Intel Chipset Software Installation Utility.........................53
VGA Drivers Installation..................................................56
Realtek HD Audio Driver Installation ..............................59
LAN Drivers Installation ..................................................61
Intel® Management Engine Interface ...............................65
Intel® USB 3.0 Drivers....................................................68
Appendix...........................................................72
A. I/O Port Address Map..................................................72
B. Interrupt Request Lines (IRQ)......................................73
C. Watchdog Timer Configuration...................................74

iv MI980 User’s Manual
This page is intentionally left blank.

INTRODUCTION
MI980 User’s Manual 1
Introduction
Product Description
The MI980 Mini ITX motherboard is based on the latest Intel®QM87
chipset. The platform supports onboard 4th generation Intel®Core
processor family features an integrated dual-channel DDR3 memory
controller as well as a graphics core.
The latest Intel®processors provide advanced performance in both
computing and graphics quality. This meets the requirement of customers
in the gaming, POS, digital signage and server market segment.
The QM87 platform is made with 22-nanometer technology that supports
Intel’s first processor architecture to unite the CPU and the graphics core
on the transistor level. The MI980 Mini ITX board utilizes the dramatic
increase in performance provided this Intel’s latest cutting-edge
technology. Measuring 170mm x 170mm, the MI980 offers fast 6Gbps
SATA support, USB3.0 and interfaces for DVI-D, DVI-I, LVDS and DP
displays.
Checklist
Your MI980 package should include the items listed below.
The MI980 MINI ITX motherboard
This User’s Manual
1 CD containing chipset drivers and flash memory utility
Serial ATA cable

INTRODUCTION
2 MI980 User’s Manual
MI980 Specifications
Product Name
MI980VF [Supports iAMT 9.0 & vPro]
MI980F [Supports EuP/ErP]
Form Factor
Mini-ITX
CPU Type
- Intel®4th Generation Core mobile processors (22nm monolithic)
- BGA1364 , Package= 37.5 mmx 32 mm [Performance Halo SKUs]
- TDP = 47W (QC) / 37W(DC)
Cache
Up to 8MB
Chipset
Intel®QM87 PCH Mobile Platform Controller Hub
Package =23 mm x 22 mm, 0.65 mm ball pitch; TDP = 3W
QM87 for MI980VF ; HM86 for MI980F
BIOS
AMI BIOS [16MB SPI ROM]
Memory
Intel®4th Generation Core mobile processors integrated memory
controller
DDRIII 1600 MHz (supports dual channel DDR3/DDR3L)
- SO-DIMM [204-pin vertical type] x 2 (Non-ECC), Max. 16GB
VGA
Intel®4thGenerationCoremobileprocessor integrated HD Gfx, supports
3 independent displays, Direct X 11.1, OpenGL 3.2, Open CL 1.2
DVI-I X 1 (Thru port B, via VGA@ QM87 PCH+ Level shifter
ASM1442)
DVI-D x 1 (Thru port C, with level shifter ASM1442)
DisplayPort x 1 (Thru port D)
LVDS (Thru eDP, via NXP PTN3460)
LAN
1. Intel® Clarkville I217LM GbE PHY [For MI980VF]
or I217V GbE PHY [For MI980F]
** Package = 6mm x 6mm, QFN48**
2. Intel®Pearsonville I211AT as 2nd GbE
USB
USB 2.0 host controller [QM87 PCH integrated], supports 8ports
- 2 ports in the rear panel
- 4 ports via onboard pin header (2.0mm pitch)
- 2 ports via MiniPCIe sockets
USB 3.0 host controller [QM87 PCH integrated] supports 4 ports
-4 ports in the rear panel for MI980VF
Serial ATA
Intel®QM87 PCH built-in SATA controller, supports 6 ports
4x SATA (3.0) 6Gbps & shared mSATA for 1 port (SATA port #5)
2x SATA (2.0) 3Gbps
** QM87 supports 4 x SATA III ; HM86 supports 2 x SATA III only**
Audio
Intel®Mobile QM87 PCH built-in High Definition Audio controller +
Realtek ALC892 w/ 7.1 channels
LPC I/O
Fintek F81866AD-I (128-pin LQFP [14mm x 14 mm])
-COM #1 (RS232/422/485) supports ring-in with power @500mA
(selectable for 5V or 12V) [EXAR SP339EER1 232/422/485
transceiver x 1 for jumper-less]
-COM #2 (RS232 only), supports ring-in with power @500mA
(selectable for 5V or 12V)
-COM #3~COM #6 (RS232 only)
Hardware Monitor (2 thermal, 4 voltage monitor inputs & 2 fan headers)
-CPU fan x 1(PWN fan type, 4-pin connector)
-SYS fan x 1 (DC/PWM Auto-Detect fan type, 4-pin connector)]
Digital IO
4 in & 4 out
TPM 1.2
Nuvoton WPCT210AA0WX (MI980VF only)
**Operation temperature for 0 ~ +60 degree C only**
iAMT
Intel®Mobile QM87 PCH built-in
- Intel®Active Management Technology, version 9.0 (MI980VF only)
Expansion Slots
- PCI-Express (16x) x1 [Gen 3.0 PEG]
- Mini PCI-Express x 2 port [Full-sized], both support USB 2.0
- One slot supports mSATA (6Gbps)

INTRODUCTION
MI980 User’s Manual 3
Edge Connectors
Dual DB9 stack connector for COM #1 / #2
DVI-D + DVI-I stack connector x 1
DisplayPort + dual USB (2.0) stack connector x 1
RJ-45 + dual USB (3.0) stack connector x 2
Triplet type Jack 3 x 1 for HD Audio
Onboard
Header/Connector
4 ports x SATA III [Blue color] (For MI980VF)
2 ports x SATA III [Blue color] (For MI980F)
2 ports x SATA II
DF-11 8-pin connector x 2 for 4 ports USB 2.0
DF-20 20-pin connector x 2 for dual –channel LVDS
eDP LVDS panel connector x 1
2x5 pin-header x 1 for front panel audio [supports 7.1 Channel]
DF-11 10-pin header x 4 for COM3 ~ COM6
2x5 pin-header x 1 for Digital IO
4-pin box header x 1 for LCD backlight control
Watchdog Timer
Yes (256 segments, 0, 1, 2…255 sec/min)
System Voltage
ATX standard 20-pin type
4 pin type (+12V only)[For full system loading usage]
Others
- vPro [MI980VF only]
- ErP feature (F81866AD-I integrated, WOL from 2nd GbE)
- iSMART ( via TI MSP430G2433 MCU)
- AT24C02C EEPROM [SO8 type] via SMbus (Reserved)
Board Size
170mm x 170mm

INTRODUCTION
4 MI980 User’s Manual
[
Board Dimensions

INSTALLATIONS
MI980 User’s Manual 5
Installations
This section provides information on how to use the jumpers and
connectors on the MI980 in order to set up a workable system. The topics
covered are:
Installing the Memory..........................................................................6
Setting the Jumpers..............................................................................7
Connectors on MI980........................................................................12

INSTALLATIONS
6 MI980 User’s Manual
Installing the Memory
The MI980 board supports two DDR3 memory socket for a maximum
total memory of 16GB in DDR3 SODIMM memory type.
Installing and Removing Memory Modules
To install the DDR3 modules, locate the memory slot on the board and
perform the following steps:
1. Hold the DDR3 module so that the key of the DDR3 module aligned
with that on the memory slot.
2. Gently push the DDR3 module in an upright position until the clips of
the slot close to hold the DDR3 module in place when the DDR3
module touches the bottom of the slot.
3. To remove the DDR3 module, press the clips with both hands.
DDR3 Module
Lock
Lock
Lock
Lock

INSTALLATIONS
MI980 User’s Manual 7
Setting the Jumpers
Jumpers are used on MI980 to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on MI980 and their respective functions.
Jumper Locations on MI980 ................................................................8
JP1: COM2 RS232 RI/+5V/+12V Power Setting.................................9
JP2: COM1 RS232 RI/+5V/+12V Power Setting.................................9
J13: LCD Panel Power Selection........................................................10
J16: Flash Descriptor Security Override (Factory use only) ................10
J17: Clear CMOS Contents................................................................11
J18: Clear ME Contents.....................................................................11

INSTALLATIONS
8 MI980 User’s Manual
Jumper Locations on MI980
Jumpers on MI980..........................................................................Page
JP1: COM2 RS232 RI/+5V/+12V Power Setting................................. 9
JP2: COM1 RS232 RI/+5V/+12V Power Setting................................. 9
J13: LCD Panel Power Selection ....................................................... 10
J16: Flash Descriptor Security Override (Factory use only) ................ 10
J17: Clear CMOS Contents................................................................ 11
J18: Clear ME Contents..................................................................... 11

INSTALLATIONS
MI980 User’s Manual 9
JP1: COM2 RS232 RI/+5V/+12V Power Setting
JP1
Setting
Function
Pin 1-3, Short/Closed
+12V
Pin 3-4, Short/Closed
RI
Pin 3-5, Short/Closed
+5V
JP2: COM1 RS232 RI/+5V/+12V Power Setting
JP2
Setting
Function
Pin 1-3, Short/Closed
+12V
Pin 3-4, Short/Closed
RI
Pin 3-5, Short/Closed
+5V
6
2
5
1
6
2
5
1

INSTALLATIONS
10 MI980 User’s Manual
J13: LCD Panel Power Selection
J13
LCD Panel Power
3.3V
5V
J16: Flash Descriptor Security Override (Factory use only)
J16
Flash Descriptor
Security Override
Open
Disabled (Default)
Close
Enabled
1
3
2
1

INSTALLATIONS
MI980 User’s Manual 11
J17: Clear CMOS Contents
J17
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS
J18: Clear ME Contents
J18
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS
3 1
3 1

INSTALLATIONS
12 MI980 User’s Manual
Connectors on MI980
Connector Locations on MI980 ......................................................... 13
CN2: DVI-I and DVI-D Connector ................................................... 14
CN1: COM1 and COM2 Serial Ports................................................. 15
CN4: Display Port ............................................................................. 15
CN5: USB2 #6/#7............................................................................. 15
CN6: Gigabit LAN (I217) + USB3 #0/#1 .......................................... 15
CN7, CN8: SATA3 Connectors......................................................... 15
CN9: Gigabit LAN (I211) + USB3 #2/#3 .......................................... 15
CN3: eDP Connector (JAE_FI-TD44SB-E-R750)............................. 16
CN10: SATA2 Connector (MI980VF only) ....................................... 17
CN11: SATA2 Connectors................................................................ 17
CN12: HD Audio Connector ............................................................. 17
CN13: SATA3 Connector (MI980VF only) ....................................... 17
CN14: SATA3 Connector support MI980VF or SATA2 Connector
suport MI980F....................................................................... 17
JP3, JP4: LVDS Connectors (LVDS2, LVDS1) Hirose
DF20G-20DP-1V.............................................................................. 17
JP5: LCD Backlight Connector.......................................................... 18
JP6, JP8: USB2 #8/#9, USB2 #4/#5 Connectors................................ 18
J1, J2, J3, J4: COM6, COM5, COM3, COM4 RS232 Serial Ports
(HIROSE DF11-10DP-2DSA)........................................................... 19
J5: ATX Power Supply Connector..................................................... 19
J6: ATX 12V Power Connector......................................................... 20
JP7: LPC debug Connector (Factory use only)................................... 20
JP9: SPI Flash Connector (Factory use only) ..................................... 20
J7: PCIE1 Configuration.................................................................... 21
J8: Digital I/O Connector (4 in, 4 out) ............................................... 21
J10, J11: DDR3 SO-DIMM Socket ................................................... 21
J12: LVDS/eDP Select ...................................................................... 22
J21: Audio Pin Header for Chassis Front Panel.................................. 22
J22: Front Panel................................................................................. 23
CPU_FAN1: CPU Fan Power Connector.......................................... 23
SYS_FAN2: System Fan Power Connector (DC/PWM Auto-Detect) 24
J14: Mini PCIE/mSATA (share with CN7) Connector ....................... 24
J15: Mini PCIE Connector................................................................. 24

INSTALLATIONS
MI980 User’s Manual 13
Connector Locations on MI980

INSTALLATIONS
14 MI980 User’s Manual
CN2: DVI-I and DVI-D Connector
Signal Name
Pin #
Pin #
Signal Name
DATA 2-
1
16
HOT POWER
DATA 2+
2
17
DATA 0-
Shield 2/4
3
18
DATA 0+
DATA 4-
4
19
SHIELD 0/5
DATA 4+
5
20
DATA 5-
DDC CLOCK
6
21
DATA 5+
DDC DATA
7
22
SHIELD CLK
Analog VSYNC
8
23
CLOCK -
DATA 1-
9
24
CLOCK +
DATA 1+
10
C1
Analog Red
SHIELD 1/3
11
C2
Analog Green
DATA 3-
12
C3
Analog Blue
DATA 3+
13
C4
Analog HSYNC
DDC POWER
14
C5
A GROUND2
A GROUND 1
15
C6
A GROUND3
[
Signal Name
Pin #
Pin #
Signal Name
DATA 2-
1
16
HOT POWER
DATA 2+
2
17
DATA 0-
Shield 2/4
3
18
DATA 0+
DATA 4-
4
19
SHIELD 0/5
DATA 4+
5
20
DATA 5-
DDC CLOCK
6
21
DATA 5+
DDC DATA
7
22
SHIELD CLK
N.C
8
23
CLOCK -
DATA 1-
9
24
CLOCK +
DATA 1+
10
C1
N.C.
SHIELD 1/3
11
C2
N.C.
DATA 3-
12
C3
N.C.
DATA 3+
13
C4
N.C.
DDC POWER
14
C5
N.C.
A GROUND 1
15
C6
N.C.

INSTALLATIONS
MI980 User’s Manual 15
CN1: COM1 and COM2 Serial Ports
[
Pin #
Signal Name
RS-232
R2-422
RS-485
1
DCD
TX-
DATA-
2
RX
TX+
DATA+
3
TX
RX+
NC
4
DTR
RX-
NC
5
Ground
Ground
Ground
6
DSR
NC
NC
7
RTS
NC
NC
8
CTS
NC
NC
9
RI
NC
NC
10
NC
NC
NC
CN4: Display Port
Signal Name
Pin #
Pin #
Signal Name
LANE0_P
1
11
GND
GND
2
12
LANE3_N
LANE0_N
3
13
GND
LANE1_P
4
14
GND
GND
5
15
AUX_P
LANE1_N
6
16
GND
LANE2_P
7
17
AUX_N
GND
8
18
HPD
LANE2_N
9
19
GND
LANE3_P
10
20
VCC3.
CN5: USB2 #6/#7
CN6: Gigabit LAN (I217) + USB3 #0/#1
CN7, CN8: SATA3 Connectors
CN9: Gigabit LAN (I211) + USB3 #2/#3

INSTALLATIONS
16 MI980 User’s Manual
CN3: eDP Connector (JAE_FI-TD44SB-E-R750)
Signal Name
Pin #
Pin #
Signal Name
3.3V
1
23
TXN0
3.3V
2
24
TXP0
3.3V
3
25
GND
3.3V
4
26
AUXP
3.3V
5
27
AUXN
GND
6
28
NC
GND
7
29
VCC3
GND
8
30
NC
GND
9
31
VCC12
HPD
10
32
NC
NC
11
33
GND
NC
12
34
VCC5
GND
13
35
NC
NC
14
36
Brightness
NC
15
37
BKLT_EN
GND
16
38
VCC12
NC
17
39
VCC3
NC
18
40
GND
GND
19
41
SMB_THRM_CLK
TXN1
20
42
SMB_THRM_DATA
TXP1
21
43
NC
GND
22
44
NC
1
44