IBASE Technology MBN800-8L User manual

MBN800-8L
MBN800-6L
Networking Motherboards
with Intel®PCH C236/H110
User’s Manual
Version 1.0a
(Nov. 2017)

ii
MBN800 Series User Manual
Copyright
©2017 IBASE Technology, Inc. All rights reserved.
No part of this publication may be reproduced, copied, stored in a retrieval system, translated
into any language or transmitted in any form or by any means, electronic, mechanical,
photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc.
(hereinafter referred to as “IBASE”).
Disclaimer
IBASE reserves the right to make changes and improvements to the products described in
this document without prior notice. Every effort has been made to ensure the information in
the document is correct; however, IBASE does not guarantee this document is error-free.
IBASE assumes no liability for incidental or consequential damages arising from
misapplication or inability to use the product or the information contained herein, nor for any
infringements of rights of third parties, which may result from its use.
Trademarks
All the trademarks, registrations and brands mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

MBN800 Series User Manual
iii
Compliance
This product has passed CE tests for environmental specifications and limits. This
product is in accordance with the directives of the Union European (EU). If users
modify and/or install other devices in this equipment, the CE conformity declaration
may no longer apply.
This product has been tested and found to comply with the limits for a Class A
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with manufacturer’s instructions, may cause
harmful interference to radio communications.
WEEE
This product must not be disposed of as normal household waste, in
accordance with the EU directive of for waste electrical and electronic
equipment (WEEE - 2012/19/EU). Instead, it should be disposed of by
returning it to a municipal recycling collection point. Check local
regulations for disposal of electronic products.
Green IBASE
This product is compliant with the current RoHS restrictions and
prohibits use of the following substances in concentrations exceeding
0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by
weight (100 ppm).
•Lead (Pb)
•Mercury (Hg)
•Cadmium (Cd)
•Hexavalent chromium (Cr6+)
•Polybrominated biphenyls (PBB)
•Polybrominated diphenyl ether (PBDE)

iv
MBN800 Series User Manual
Important Safety Information
Carefully read the precautions before using the device.
Environmental conditions:
•Lay the device horizontally on a stable and solid surface in case the device may
fall, causing serious damage.
•Slots and openings on the chassis are for ventilation. Do not block or cover these
openings. Make sure you leave plenty of space around the device for ventilation.
NEVER INSERT OBJECTS OF ANY KIND INTO THE VENTILATION
OPENINGS.
•Use this product in environments at ambient temperatures 0˚C ~ 60˚.
•DO NOT LEAVE THIS DEVICE IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20˚C OR ABOVE 80˚C. This
could damage the device. The device must be used in a controlled environment.
Care for your IBASE products:
•Before cleaning the device, turn it off and unplug all cables such as power in case
a small amount of electrical current may still flow.
•Use neutral cleaning agents or diluted alcohol to clean the device chassis with a
cloth. Then wipe the chassis with a dry cloth.
•Vacuum the dust with a computer vacuum cleaner to prevent the air vent or slots
from being clogged.
WARNING
Attention during use:
•Do not use this product near water.
•Do not spill water or any other liquids on your device.
•Do not place heavy objects on the top of the device.
•Operate this device from the type of power indicated on the marking label. If you
are not sure of the type of power available, consult your distributor or local
power company.
•Do not walk on the power cord or allow anything to rest on it.
•If you use an extension cord, make sure that the total ampere rating of the
product plugged into the extension cord does not exceed its limits.
•When handling processor chips or memory modules, avoid touching their pins or
gold fingers. Put modules or peripherals back into antistatic bags when they are
not in use or not installed in the chassis.
Avoid Disassembly
You are not suggested to disassemble, repair or make any modification to the device.
Disassembly, modification, or any attempt at repair could generate hazards and
cause damage to the device, even bodily injury or property damage, and will void any
warranty.

MBN800 Series User Manual
v
CAUTION
Danger of explosion if internal lithium-ion battery is replaced by an incorrect type.
Replace only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions. Under no
circumstances should the Lithium battery cell be shorted; otherwise the battery cell
may heat up or cause potential burn hazards.
Warranty Policy
•IBASE standard products:
24-month (2-year) warranty from the date of shipment. If the date of shipment
cannot be ascertained, the product serial numbers can be used to determine
the approximate shipping date.
•3rd-party parts:
12-month (1-year) warranty from delivery for the 3rd-party parts that are not
manufactured by IBASE, such as CPU, memory, HDD, power adapter, panel
and touchscreen.
＊PRODUCTS, HOWEVER, THAT FAILS DUE TO MISUSE, ACCIDENT,
IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE
TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE BILLED
FOR REPAIR AND SHIPPING CHARGES.
Technical Support & Services
1. Visit the IBASE website at www.ibase.com.tw to find the latest information about
the product.
2. If you need any further assistance from your distributor or sales representative,
prepare the following information of your product and elaborate upon the
problem.
•Product model name
•Product serial number
•Detailed description of the problem
•The error messages in text or in screenshots if there is any
•The arrangement of the peripherals
•Software in use (such as OS and application software, including the version
numbers)
3. If repair service is required, you can download the RMA form at
http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and
contact your distributor or sales representative.

vi
MBN800 Series User Manual
Table of Contents
Compliance....................................................................................................iii
Important Safety Information.......................................................................iv
WARNING ......................................................................................................iv
CAUTION ........................................................................................................v
Warranty Policy..............................................................................................v
Technical Support & Services ......................................................................v
Chapter 1 General Information................................................................1
1.1 Introduction.............................................................................................2
1.2 Features..................................................................................................3
1.3 Packing List ............................................................................................3
1.4 Optional Accessories ..............................................................................3
1.5 Specifications..........................................................................................4
1.6 Overview.................................................................................................5
1.7 Dimensions.............................................................................................6
Chapter 2 Hardware Configuration.........................................................7
2.1 Essential Installations Before You Begin.................................................8
2.1.1 CPU Installation / Replacement................................................8
2.1.2 Memory Installation / Replacement...........................................9
2.1.3 CF Card & IPMI Module Installation / Replacement................10
2.2 Setting the Jumpers..............................................................................11
2.2.1 How to Set Jumpers ...............................................................11
2.3 Jumper & Connector Locations on Motherboard...................................12
2.4 Jumpers Quick Reference.....................................................................14
2.4.1 ME Register Clearance (JBAT3)..........................................14
2.4.2 CMOS Data Clearance (JBAT4)...........................................15
2.5 Connectors Quick Reference................................................................16
2.5.1 System Function Connector (JP3)........................................17
2.5.2 Digital I/O Port (JP4)............................................................19
2.5.3 External SATA Power (CN2, CN4).......................................20
2.5.4 LCM Port (CN5)...................................................................21
2.5.5 Fan Connector (FAN_CPU, FAN1, FAN2, FAN3, FAN4)......22
2.5.6 System Power Switch (J1) ...................................................23

MBN800 Series User Manual
vii
2.5.7 ATX Power Connector (J2, J14)...........................................24
2.5.8 External VGA Port (J3).........................................................25
Chapter 3 BIOS Setup............................................................................26
3.1 Introduction...........................................................................................27
3.2 BIOS Setup...........................................................................................27
3.3 Main Settings........................................................................................28
3.4 Advanced Settings................................................................................29
3.4.1 CPU Configuration..................................................................29
3.4.2 Trusted Computing.................................................................30
3.4.3 SATA Configuration................................................................31
3.4.4 SMART Setting.......................................................................31
3.4.5 NCT5523D Super IO Configuration ........................................32
3.4.6 Hardware Monitor...................................................................35
3.4.7 LAN Bypass Configuration......................................................36
3.4.8 Console Port Configuration.....................................................36
3.4.9 USB Configuration..................................................................38
3.5 Security Settings...................................................................................39
3.6 Boot Settings.........................................................................................40
3.7 Save & Exit Settings..............................................................................41
3.8 Server Management..............................................................................42
3.8.1 BMC SOL Function.................................................................43
3.8.2 BMC Network Configuration ...................................................44
Appendix ......................................................................................................45
A. I/O Port Address Map............................................................................46
B. Interrupt Request Lines (IRQ)...............................................................51
C. Digital I/O Sample Code........................................................................55
D. Watchdog Timer Configuration..............................................................60

1
Chapter 1
General Information
The information provided in this chapter includes:
•Features
•Packing List
•Optional Accessories
•Specifications
•Overview
•Dimensions

2
MBN800 Series User Manual
1.1 Introduction
MBN800 series are specifically designed for the network security and
management market. There are plenty of applications adopting network
security or network management as listed below.
MBN800 series include the following models:
•MBN800-8L (with Intel®PCH C236)
•MBN800-6L (with Intel®PCH H110)
Network Security Applications:
•Firewall
•Unified Threat Management (UTM)
•Virtual Private Network (VPN)
•Proxy Server
•Caching Server
Network Management Applications:
•Load balancing
•Quality of Service
•Remote Access Service
The Networking motherboard product line covers the spectrum from offering
platforms designed for:
•SOHO
•SMB
•Enterprise
Each product is designed to address the distinctive requirements of its
respective market segment from cost effective entry-level solutions to high
throughput and performance-bound systems for the enterprise level.

General Information
MBN800 Series User Manual
3
1
1.2 Features
•Supports Intel®Xeon®6th Gen. Core™ i7/i5/i3 processor
•DDR4 DIMM 2133 MHz (ECC supported per CPU SKUs)
•Up to 8 GbE LAN ports with 2 advanced LAN Bypass pairs
•Optional IPMI 2.0 module to output through VGA port for MBN800-8L
•CF slot and PCIe (x8) expansion slot(s)
•250W single power supply or 300W 1+1 redundant power supply
1.3 Packing List
Your product package should include the items listed below. If any of the
items below is missing, contact the distributor or the dealer from whom you
purchased the product.
•MBN800-8L / MBN800-6L
1.4 Optional Accessories
IBASE provide optional accessories as follows. Please contact us or your
dealer if you need any.
•Console Cable (160 cm, PK1-51)
•VGA Cable (40 cm, VGA21A)

4
MBN800 Series User Manual
1.5 Specifications
Motherboard
MBN800-8L
MBN800-6L
Operating
System
•Windows 10 (64-bit)
•Linux Ubuntu 16.04.3
CPU
Intel®Xeon®/ 6th Gen. Core™
i7/i5/i3 processor LGA1151
Intel®6th Gen. Core™ i7/i5/i3
processor LGA1151
Chipset
Intel®C236 PCH
Intel®H110 PCH
Memory
4 x DDR4 DIMM 2133 MHz,
expandable to 64 GB
* ECC supported per CPU
SKUs
2 x DDR4 DIMM 2133 MHz,
expandable to 32 GB
(non-ECC)
Storage
•2 x 2.5” / 3.5” HDD or SSD drive bay
•On-board CF slot
Network
8 x Intel®I210AT GbE
6 x Intel®I211AT GbE
Bypass
2 x segments (LAN1 / LAN2 & LAN3 / LAN4)
NIC Slot
1 x IBN card series
N/A
Super I/O
Nuvoton NCT5523D
IPMI
IPMI module compliant with
IPMI 2.0 (Optional)
N/A
Power Supply
•Full range 250W ATX power supply
Power
Requirement
100 ~ 240V AC
BIOS
AMI BIOS
TPM
1.2
Watchdog
Watchdog Timer 256 segments, 0, 1, 2…255 sec/min
Chassis
Steel with textured black color paint
Dimensions
362 x 183 mm (13.78” x 7.2”)
Weight
0.5 kg (1.1 lb)
Certificate
CE / FCC Class A / LVD
Environment
Temperature
•Operating: 0 ~ 60 °C (32 ~ 140 °F)
•Storage: -20~ 80 °C (-4 ~ 176 °F)
Relative
Humidity
5 ~ 90%
All specifications are subject to change without prior notice.

General Information
MBN800 Series User Manual
5
1
1.6 Overview
MBN800-8L
MBN800-6L

6
MBN800 Series User Manual
1.7 Dimensions
Unit: mm

7
Chapter 2
Hardware Configuration
The information provided in this chapter includes:
•Essential installations
•Information and locations of connectors

8
MBN800 Series User Manual
2.1 Essential Installations
For installation or replacement of CPU, memory modules, CF card, IPMI card
& mini-PCIe card (IPMI & mini-PCIe slots are both available for MBN800-8L).
2.1.1 CPU Installation / Replacement
Follow the instructions below to install or replace the CPU if necessary.
1. Unlock the CPU socket by pressing the lever sideways, then lift up the
lever and the metal lid.
2. Position the CPU above the socket such that the CPU corner aligns with
the gold triangle matching the socket corner with a small triangle.
3. Carefully insert the CPU into the socket and push down the lever to
secure the CPU.
Then you can install the CPU cooler and fan back.
Note: Ensure that the CPU cooler and the CPU top surface are in total contact
to avoid CPU overheating problem that would cause your system to hang
or be unstable.

Hardware Configuration
MBN800 Series User Manual
9
2
2.1.2 Memory Installation / Replacement
If you need to install or replace a memory module, follow the instructions
below for installation after you disassemble the device cover.
1. Press the ejector tab of the memory slot down and outwards with your
fingertips.
2. Hold the memory module and align the key of the module with that on the
memory slot.
3. Gently push the module in an upright position until the ejector tabs of the
memory slot close to hold the module in place when the module touches
the bottom of the slot.
To remove the module, press the ejector tabs outwards with your fingertips to
eject the module.

10
MBN800 Series User Manual
2.1.3 CF Card & IPMI Module Installation / Replacement
If you need to install a CF card or an IPMI module, remove the device cover
firstly and then follow the instructions below.
Note:
1. IPMI slot is available for MBN800-8L only.
2. IPMI module is optional for purchase.
IPMI module:
1. Locate the IPMI slot and align the key of the module with that on the slot.
2. Insert the module slantwise and gently push the module straight down
until the clips of the slot close to hold the module in place when the
module touches the bottom of the slot.
.
To remove the module, press the clips outwards with your thumb and index
finger of both hands.
CF card:
Locate the CF slot and Insert the CF card to the slot.
To remove the CF card or IPMI module, pull it out with your thumb and index
finger directly.

Hardware Configuration
MBN800 Series User Manual
11
2
2.2 Setting the Jumpers
Set up and configure your MBN800 series by using jumpers for various
settings and features according to your needs and applications. Contact your
supplier if you have doubts about the best configuration for your use.
2.2.1 How to Set Jumpers
Jumpers are short-length conductors consisting of several metal pins with a
non-conductive base mounted on the circuit board. Jumper caps are used to
have the functions and features enabled or disabled. If a jumper has 3 pins,
you can connect either PIN1 to PIN2 or PIN2 to PIN3 by shorting.
A 3-pin jumper
A jumper cap
Refer to the illustration below to set jumpers.
Pin closed
Oblique view
Schematic illustration in the manual
Open
1-2
2-3
When two pins of a jumper are encased in a jumper cap, this jumper is
closed, i.e. turned On.
When a jumper cap is removed from two jumper pins, this jumper is open, i.e.
turned Off.
Pin# 1 23
1 2 3
1 2 3
1 2 3

12
MBN800 Series User Manual
2.3 Jumper & Connector Locations on Motherboard
Motherboard: MBN800-8L

Hardware Configuration
MBN800 Series User Manual
13
2
Motherboard: MBN800-6L