IBASE Technology SE-103-N User manual

SE-103-N
Intel® Atom® x6000
Fanless Signage Player
User’s Manual
Version 1.0
(October 2022)

ii SE-103-N User Manual
Copyright
© 2022 IBASE Technology, Inc. All rights reserved.
No part of this publication may be reproduced, copied, stored in a retrieval system, translated
into any language or transmitted in any form or by any means, electronic, mechanical,
photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc.
(hereinafter referred to as “IBASE”).
Disclaimer
IBASE reserves the right to make changes and improvements to the products described in
this document without prior notice. Every effort has been made to ensure the information in
the document is correct; however, IBASE does not guarantee this document is error-free.
IBASE assumes no liability for incidental or consequential damages arising from
misapplication or inability to use the product or the information contained herein, nor for any
infringements of rights of third parties, which may result from its use.
Trademarks
All the trademarks, registrations and brands mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

SE-103-N User Manual ii
i
Compliance
In a domestic environment, this product may cause radio interference in which case
users may be required to take adequate measures.
This product has been tested and found to comply with the limits for a Class B
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with manufacturer’s instructions, may cause
harmful interference to radio communications.
WEEE
This product must not be disposed of as normal household waste, in
accordance with the EU directive of for waste electrical and electronic
equipment (WEEE - 2012/19/EU). Instead, it should be disposed of by
returning it to a municipal recycling collection point. Check local
regulations for disposal of electronic products.
Green IBASE
This product is compliant with the current RoHS restrictions and
prohibits use of the following substances in concentrations exceeding
0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by
weight (100 ppm).
• Lead (Pb)
• Mercury (Hg)
• Cadmium (Cd)
• Hexavalent chromium (Cr6+)
• Polybrominated biphenyls (PBB)
• Polybrominated diphenyl ether (PBDE)

iv SE-103-N User Manual
Important Safety Information
Carefully read the precautions before using the device.
Environmental conditions:
 Lay the device horizontally on a stable and solid surface in case the device may
fall, causing serious damage.
 Leave plenty of space around the device and do not block the openings for
ventilation. NEVER DROP OR INSERT ANY OBJECTS OF ANY KIND INTO
THE VENTIILATION OPENINGS.
 Use this product in environments with ambient temperatures between 0˚C and
45˚C.
 DO NOT LEAVE THIS DEVICE IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY IS BELOW -20° C OR ABOVE 80° C. This
could damage the device. The device must be used in a controlled environment.
Care for IBASE products:
 Before cleaning the device, turn it off and unplug all cables such as power in case
a small amount of electrical current may still flow.
 Use neutral cleaning agents or diluted alcohol to clean the device chassis with a
cloth. Then wipe the chassis with a dry cloth.
 Vacuum the dust with a computer vacuum cleaner to prevent the air vent or slots
from being clogged.
WARNING
Attention during use:
 Do not place heavy objects on the top of the device.
 Operate this device from the type of power indicated on the marking label. If you
are not sure of the type of power available, consult the distributor or local power
company.
 Do not walk on the power cord or allow anything to rest on it.
 If you use an extension cord, make sure that the total ampere rating of the
product plugged into the extension cord does not exceed its limits.
Avoid Disassembly
Do not disassemble, repair or make any modification to the device. Doing so could
generate hazards and cause damage to the device, even bodily injury or property
damage, and will void any warranty.

SE-103-N User Manual
v
CAUTION
There is danger of explosion if internal lithium-ion battery is replaced by an incorrect
type. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
Warranty Policy
 IBASE standard products:
24-month (2-year) warranty from the date of shipment. If the date of shipment
cannot be ascertained, the product serial numbers can be used to determine
the approximate shipping date.
 3rd-party parts:
12-month (1-year) warranty from delivery for the 3rd-party parts that are not
manufactured by IBASE, such as CPU, CPU cooler, memory, storage devices,
power adapter, panel and touchscreen.
＊ PRODUCTS, HOWEVER, THAT FAIL DUE TO MISUSE, ACCIDENT,
IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE
TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE BILLED
FOR REPAIR AND SHIPPING CHARGES.
Technical Support & Services
1. Visit the IBASE website at www.ibase.com.tw to find the latest information about
the product.
2. If you need any further assistance from the distributor or sales representative,
prepare the following information:
 Product model name
 Product serial number
 Detailed description of the problem
 The error messages in text or in screenshots if there is any
 The arrangement of the peripherals
 Software in use (such as OS and application software, including the version
numbers)
3. If repair service is required, you can download the RMA form at
http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and
contact the distributor or sales representative.

vi SE-103-N User Manual
TableofContents
Chapter 1 General Information ............................................................. 1
1.1Introduction ............................................................................................... 2
1.2Features ................................................................................................... 2
1.3Packing List .............................................................................................. 3
1.4Specifications ........................................................................................... 3
1.5Product View ............................................................................................ 5
1.6Dimensions ............................................................................................... 7
Chapter 2 Hardware Installation & Motherboard Information .............. 8 
2.1Installation / Replacement ........................................................................ 9
2.2Setting the Jumpers ................................................................................ 14
2.3Jumper & Connector Locations on Motherboard .................................... 15
Chapter 3 Driver Installation ................................................................. 20
3.1Introduction ............................................................................................. 21
3.2Intel® Chipset Software Installation Utility ............................................... 21
3.3VGA Driver Installation ........................................................................... 23
3.4HD Audio Driver Installation ................................................................... 25
3.5Intel® ME Drivers Installation ................................................................. 26
3.6Observer Utility Installation ..................................................................... 28
3.7LAN Drivers Installation .......................................................................... 29
Chapter 4 BIOS Setup ............................................................................ 31
4.1Introduction ............................................................................................. 32
4.2BIOS Setup ............................................................................................. 32
4.3Main Settings .......................................................................................... 33
4.4Advanced Settings .................................................................................. 33
4.5Chipset Settings ..................................................................................... 44
4.6Security Settings ..................................................................................... 47
4.7Boot Settings .......................................................................................... 49
4.8Save & Exit Settings ............................................................................... 50
Appendix ...................................................................................................... 51
A.I/O Port Address Map ............................................................................. 52
B.Interrupt Request Lines (IRQ) ................................................................ 54

1
Chapter 1
General Information
The information provided in this chapter includes:
 Features
 Packing List
 Accessories
 Specifications
 Product View
 Dimensions

2 SE-103-N User Manual
1.1 Introduction
The SE-103-N is a fanless digital signage player that leverages the Intel® x6000
family processors that can be install in commercial establishments to increase brand
awareness and customer engagement or deployed in transportation networks to
provide real-time information and advertising relevant to the traveler.
The fanless SE-103-N offers high performance and high reliability for 24/7 operation
in an industrial-grade design and is integrated with the IBASE iSMART and Observer
technologies for remote monitoring, power on/off scheduling, power recovery and low
temperature boot functions. The system supports three independent displays (3x
HDMI 2.0b with HDMI-CEC display on/off control function), up to 32GB DDR4-3200
memory, and Intel® 2.5GbE LAN, as well as M.2 B-Key (3052) socket for 5G options
and M.2 E-Key (2230) socket for Wi-Fi, Bluetooth or capture card options.
1.2 Features
 iSMART energy-saving & Observer remote monitoring technologies
 Intel® Atom® x6000/ Pentium® / Celeron® Processors
 3x HDMI 2.0b with HDMI-CEC display on/off control function
 Built-in hardware EDID emulation with S/W control function
 2x DDR4-3200 SO-DIMM, Dual channel, Max. 32GB
 1x Intel® 2.5GbE LAN
 1x M.2 B-Key (3052) for 5G options
 1x M.2 E-Key (2230) for Wi-Fi, Bluetooth or capture card options
 TPM 2.0 and watchdog timer
 Wide-range operating temperature from -20°C to 70°C

General Information
SE-103-N User Manual 3
1
1.3 Packing List
The product package should include the items listed below. If any of the items
below is missing, contact the distributor or the dealer from whom you
purchased the product.
 SE-103-N Digital Signage Player
 Power Adaptor
 Power Cord
1.4 Specifications
Product SE-103-N
Mainboard
Mainboard MBD103 MBD103-6210
CPU Type Atom® x6425E Celeron® N6210
CPU Speed 1.8GHz
3.0GHz
1.2GHz
2.6GHz
Cache 1.5MB 1.5MB
System
Operating
System
Win10 IoT Enterprise (64-bit)
Linux Ubuntu (64-bit)
CPU Intel® Atom® x6425E (2.0~3.0GHz)
Intel® Celeron® N6210 (1.2~2.6GHz)
Chipset SoC Integrated
Memory 2x DDR4-3200 SO-DIMM, dual channel, Max. 32GB
Supports IBECC for x6000 Series CPU
Graphics 11th Gen Intel® SoC integrated 18EUs graphics device
LAN
Controller
1x Intel® I225IT 2.5GbE LAN for Atom® x6000 series
1x Intel® I225V 2.5GbE LAN for Celeron®/ Pentium®
Expansion
Slots
1x M.2 E-Key (2230), 1x M.2 B-Key (3052)
1x UIM/SIM card slot
Storage 1x M.2 M-Key (2280)
Power +12V DC
Chassis Aluminum + SGCC, black & white
Mounting Standard system bracket

4 SE-103-N User Manual
I/O Interface
3x HDMI 2.0b
3x USB 3.1 (Gen.2)
1x RJ45 for 2.5GbE LAN
1x RJ45 for RS232/422/485 serial port
2x Audio connectors for Line-in / Line-out
1x Power button
1x Terminal block for power port
1x UIM/SIM card slot
1x Power / HDD LED
4x DI, 4x DO pin header (w/o isolation) (Internal)
TPM 2.0
Auto Control
& Monitoring Watchdog Timer: 256 segments, 0, 1, 2...255 (sec/min)
Dimensions
(W x H x D)
260mm(W) x 181.4mm(D) x 25mm(H)
10.24” (W) x 7.14” (D) x 0.98” (H)
Net Weight 1.7Kg (3.75lbs)
Certificate CE, FCC class B, UL, CCC
Environment
Temperature
MBD103 (CPU x6425E) MBD103-6413 (CPU N6210
)
Operating: -20°C ~ 85 °C
(-4 ~ 185 °F)
Operating: 0°C ~ 60 °C
(32 ~ 140 °F)
Storage: -40°C ~ 110 °C
(-40 ~ 230 °F)
Storage: -20°C ~ 80 °C
(-4 ~ 176 °F)
Relative
Humidity 5 ~ 90% at 45 °C (non-condensing)
Vibration
Protection SSD: random operation 5 grms, 5~500 Hz
All specifications are subject to change without prior notice.
Note: The product performance relies on the system functioning as a whole. The
level of CPU/APU/GPU processor, the interaction among the processor and
the memory and storage bandwidth, or the functionality of the digital signage
application software may affect the product performance.