IBM BladeCenter HS20 7981 User manual

BladeCenter HS20 Ty p e 7981
Problem Determination and Service Guide


BladeCenter HS20 Ty p e 7981
Problem Determination and Service Guide


Note: Before using this information and the product it supports, read the general information in Appendix B, “Notices,” on page 85,
and the Warranty and Support Information document on the IBM BladeCenter Documentation CD.
First Edition (March 2006)
©Copyright International Business Machines Corporation 2006. All rights reserved.
US Government Users Restricted Rights –Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.

Contents
Safety ............................ vii
Guidelines for trained service technicians ............... viii
Inspecting for unsafe conditions ................. viii
Guidelines for servicing electrical equipment ............. viii
Safety statements ........................ix
Chapter 1. Introduction ......................1
Related documentation ......................1
Notices and statements in this document ................2
Features and specifications .....................3
Blade server controls, LEDs, and connectors ..............4
Turning on the blade server.....................6
Turning off the blade server.....................6
System-board layouts .......................7
System-board connectors ....................7
System-board switches .....................7
System-board LEDs ......................8
Chapter 2. Diagnostics ......................9
Diagnostic tools .........................9
POST.............................9
POST beep codes .......................9
Error logs ..........................16
POST error codes.......................18
Checkout procedure .......................24
About the checkout procedure ..................24
Performing the checkout procedure ................25
Troubleshooting tables ......................25
CD or DVD drive problems ...................26
Diskette drive problems.....................27
General problems .......................27
Hard disk drive problems ....................28
Intermittent problems......................28
Keyboard, mouse, or pointing-device problems ............29
Memory problems .......................30
Microprocessor problems ....................30
Monitor or video problems ....................31
Network connection problems ..................32
Optional-device problems ....................33
Power error messages .....................33
Power problems .......................35
ServerGuide problems .....................36
Service processor problems ...................37
Software problems ......................37
Universal Serial Bus (USB) port problems ..............37
Light path diagnostics ......................38
Viewing the light path diagnostics LEDs...............38
Light path diagnostics LEDs ...................40
Diagnostic programs, messages, and error codes ............41
Running the diagnostic programs .................41
Diagnostic text messages ....................42
Viewing the test log ......................43
Diagnostic error codes .....................43
©Copyright IBM Corp. 2006 iii

Recovering from aBIOS update failure ................48
Service processor (BMC) error codes ................49
Solving SAS hard disk drive problems ................49
Solving undetermined problems...................49
Calling IBM for service ......................50
Chapter 3. Parts listing, Type 7981 .................53
Chapter 4. Removing and replacing blade server components ......55
Installation guidelines ......................55
System reliability guidelines ...................56
Handling static-sensitive devices .................56
Returning adevice or component .................56
Removing the blade server from aBladeCenter unit ...........57
Installing the blade server in aBladeCenter unit.............58
Removing and replacing Tier 1CRUs ................59
Removing the blade server cover .................59
Installing the blade server cover .................60
Removing the bezel assembly ..................61
Installing the bezel assembly...................61
Removing aSAS hard disk drive .................62
Installing aSAS hard disk drive ..................63
Removing amemory module...................63
Installing amemory module ...................64
Removing asmall-form-factor expansion card ............66
Installing asmall-form-factor expansion card .............66
Removing astandard-form-factor expansion card ...........67
Installing astandard-form-factor expansion card............69
Removing the battery .....................70
Installing the battery ......................70
Removing and replacing FRUs ...................72
Removing amicroprocessor and heat sink..............72
Installing amicroprocessor and heat sink ..............74
Removing the system board assembly ...............78
Installing the system board assembly................78
Chapter 5. Configuration information and instructions .........79
Firmware updates ........................79
Using the Configuration/Setup Utility program .............79
Configuring the Gigabit Ethernet controllers ..............79
Blade server Ethernet controller enumeration ..............80
Configuring aSAS RAID .....................81
Appendix A. Getting help and technical assistance ..........83
Before you call .........................83
Using the documentation .....................83
Getting help and information from the World Wide Web ..........83
Software service and support ...................84
Hardware service and support ...................84
Appendix B. Notices ......................85
Edition notice .........................85
Trademarks ..........................86
Important notes.........................86
Product recycling and disposal ...................87
Battery return program ......................88
iv BladeCenter HS20 Type 7981: Problem Determination and Service Guide

Electronic emission notices ....................89
Federal Communications Commission (FCC) statement .........89
Industry Canada Class Aemission compliance statement ........89
Australia and New Zealand Class Astatement ............89
United Kingdom telecommunications safety requirement.........89
European Union EMC Directive conformance statement .........89
Taiwanese Class Awarning statement ...............90
Chinese Class Awarning statement ................90
Japanese Voluntary Control Council for Interference (VCCI) statement ...90
Index ............................91
Contents v

vi BladeCenter HS20 Type 7981: Problem Determination and Service Guide

Safety
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Lees voordat udit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d’installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.
Antes de instalar este producto, lea la información de seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
©Copyright IBM Corp. 2006 vii

Guidelines for trained service technicians
This section contains information for trained service technicians.
Inspecting for unsafe conditions
Use the information in this section to help you identify potential unsafe conditions in
an IBM product on which you are working. Each IBM product, as it was designed
and manufactured, has required safety items to protect users and service
technicians from injury. The information in this section addresses only those items.
Use good judgment to identify potential unsafe conditions that might be caused by
non-IBM alterations or attachment of non-IBM features or options that are not
addressed in this section. If you identify an unsafe condition, you must determine
how serious the hazard is and whether you must correct the problem before you
work on the product.
Consider the following conditions and the safety hazards that they present:
vElectrical hazards, especially primary power. Primary voltage on the frame can
cause serious or fatal electrical shock.
vExplosive hazards, such as adamaged CRT face or abulging capacitor.
vMechanical hazards, such as loose or missing hardware.
To inspect the product for potential unsafe conditions, complete the following steps:
1. Make sure that the power is off and the power cord is disconnected.
2. Make sure that the exterior cover is not damaged, loose, or broken, and
observe any sharp edges.
3. Check the power cord:
vMake sure that the third-wire ground connector is in good condition. Use a
meter to measure third-wire ground continuity for 0.1 ohm or less between
the external ground pin and the frame ground.
vMake sure that the power cord is the correct type, as specified in the
documentation for your BladeCenter unit type.
vMake sure that the insulation is not frayed or worn.
4. Remove the cover.
5. Check for any obvious non-IBM alterations. Use good judgment as to the safety
of any non-IBM alterations.
6. Check inside the server for any obvious unsafe conditions, such as metal filings,
contamination, water or other liquid, or signs of fire or smoke damage.
7. Check for worn, frayed, or pinched cables.
8. Make sure that the power-supply cover fasteners (screws or rivets) have not
been removed or tampered with.
Guidelines for servicing electrical equipment
Observe the following guidelines when servicing electrical equipment:
vCheck the area for electrical hazards such as moist floors, non-grounded power
extension cords, and missing safety grounds.
vUse only approved tools and test equipment. Some hand tools have handles that
are covered with asoft material that does not provide insulation from live
electrical current.
vRegularly inspect and maintain your electrical hand tools for safe operational
condition. Do not use worn or broken tools or testers.
viii BladeCenter HS20 Type 7981: Problem Determination and Service Guide

vDo not touch the reflective surface of adental mirror to alive electrical circuit.
The surface is conductive and can cause personal injury or equipment damage if
it touches alive electrical circuit.
vSome rubber floor mats contain small conductive fibers to decrease electrostatic
discharge. Do not use this type of mat to protect yourself from electrical shock.
vDo not work alone under hazardous conditions or near equipment that has
hazardous voltages.
vLocate the emergency power-off (EPO) switch, disconnecting switch, or electrical
outlet so that you can turn off the power quickly in the event of an electrical
accident.
vDisconnect all power before you perform amechanical inspection, work near
power supplies, or remove or install main units.
vBefore you work on the equipment, disconnect the power cord. If you cannot
disconnect the power cord, have the customer power-off the wall box that
supplies power to the equipment and lock the wall box in the off position.
vNever assume that power has been disconnected from acircuit. Check it to
make sure that it has been disconnected.
vIf you have to work on equipment that has exposed electrical circuits, observe
the following precautions:
–Make sure that another person who is familiar with the power-off controls is
near you and is available to turn off the power if necessary.
–When you are working with powered-on electrical equipment, use only one
hand. Keep the other hand in your pocket or behind your back to avoid
creating acomplete circuit that could cause an electrical shock.
–When using atester, set the controls correctly and use the approved probe
leads and accessories for that tester.
–Stand on asuitable rubber mat to insulate you from grounds such as metal
floor strips and equipment frames.
v
Use extreme care when measuring high voltages.
vTo ensure proper grounding of components such as power supplies, pumps,
blowers, fans, and motor generators, do not service these components outside of
their normal operating locations.
vIf an electrical accident occurs, use caution, turn off the power, and send another
person to get medical aid.
Safety statements
Important:
Each caution and danger statement in this documentation begins with anumber.
This number is used to cross reference an English-language caution or danger
statement with translated versions of the caution or danger statement in the Safety
Information document.
For example, if acaution statement begins with anumber 1, translations for that
caution statement appear in the Safety Information document under statement 1.
Be sure to read all caution and danger statements in this documentation before
performing the instructions. Read any additional safety information that comes with
your server or optional device before you install the device.
Safety ix

Statement 1:
DANGER
Electrical current from power, telephone, and communication cables is
hazardous.
To avoid ashock hazard:
vDo not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical
storm.
vConnect all power cords to aproperly wired and grounded electrical
outlet.
vConnect to properly wired outlets any equipment that will be attached to
this product.
vWhen possible, use one hand only to connect or disconnect signal
cables.
vNever turn on any equipment when there is evidence of fire, water, or
structural damage.
vDisconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
vConnect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached
devices.
To Connect: To Disconnect:
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
1. Turn everything OFF.
2. First, remove power cords from outlet.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
xBladeCenter HS20 Type 7981: Problem Determination and Service Guide

Statement 2:
CAUTION:
When replacing the lithium battery, use only IBM Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has
amodule containing alithium battery, replace it only with the same module
type made by the same manufacturer. The battery contains lithium and can
explode if not properly used, handled, or disposed of.
Do not:
vThrow or immerse into water
vHeat to more than 100°C (212°F)
vRepair or disassemble
Dispose of the battery as required by local ordinances or regulations.
Statement 3:
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
vDo not remove the covers. Removing the covers of the laser product could
result in exposure to hazardous laser radiation. There are no serviceable
parts inside the device.
vUse of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser
diode. Note the following.
Laser radiation when open. Do not stare into the beam, do not view directly
with optical instruments, and avoid direct exposure to the beam.
Safety xi

Statement 4:
≥18 kg (39.7 lb) ≥32 kg (70.5 lb) ≥55 kg (121.2 lb)
CAUTION:
Use safe practices when lifting.
Statement 5:
CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current
from the device, ensure that all power cords are disconnected from the power
source.
1
2
xii BladeCenter HS20 Type 7981: Problem Determination and Service Guide

Statement 8:
CAUTION:
Never remove the cover on apower supply or any part that has the following
label attached.
Hazardous voltage, current, and energy levels are present inside any
component that has this label attached. There are no serviceable parts inside
these components. If you suspect aproblem with one of these parts, contact
aservice technician.
Statement 10:
CAUTION:
Do not place any object on top of rack-mounted devices.
Safety xiii

xiv BladeCenter HS20 Type 7981: Problem Determination and Service Guide

Chapter 1. Introduction
This Problem Determination and Service Guide contains information to help you
solve problems that might occur in your IBM
® BladeCenter HS20 Type 7981 blade
server. It describes the diagnostic tools that come with the blade server, error codes
and suggested actions, and instructions for replacing failing components.
Replaceable components are of three types:
vTier 1customer replaceable unit (CRU): Replacement of Tier 1CRUs is your
responsibility. If IBM installs aTier 1CRU at your request, you will be charged for
the installation.
vTier 2customer replaceable unit: You may install aTier 2CRU yourself or
request IBM to install it, at no additional charge, under the type of warranty
service that is designated for your server.
vField replaceable unit (FRU): FRUs must be installed only by trained service
technicians.
For information about the terms of the warranty and getting service and assistance,
see the Warranty and Support Information document.
Related documentation
In addition to this document, the following documentation also comes with the
server:
vInstallation and User’s Guide
This printed document contains general information about the server, including
how to install supported options and how to configure the server.
vSafety Information
This document is in Portable Document Format (PDF) on the Documentation CD.
It contains translated caution and danger statements. Each caution and danger
statement that appears in the documentation has anumber that you can use to
locate the corresponding statement in your language in the Safety Information
document.
vWarranty and Support Information
This document is in PDF on the Documentation CD. It contains information about
the terms of the warranty and about service and assistance.
Depending on the server model, additional documentation might be included on the
IBM Documentation CD.
The blade server might have features that are not described in the documentation
that comes with the server. The documentation might be updated occasionally to
include information about those features, or technical updates might be available to
provide additional information that is not included in the blade server
documentation. The most recent versions of all BladeCenter documentation are at
http://www.ibm.com/support/. In addition to the documentation in this library, be sure
to review the IBM BladeCenter Planning and Installation Guide for your BladeCenter
unit type for information to help you prepare for system installation and
configuration. This document is available at http://www.ibm.com/bladecenter/.
©Copyright IBM Corp. 2006 1

Notices and statements in this document
The caution and danger statements that appear in this document are also in the
multilingual Safety Information document, which is on the IBM Documentation CD.
Each statement is numbered for reference to the corresponding statement in the
Safety Information document.
The following notices and statements are used in this document:
vNote: These notices provide important tips, guidance, or advice.
vImportant: These notices provide information or advice that might help you avoid
inconvenient or problem situations.
vAttention: These notices indicate potential damage to programs, devices, or
data. An attention notice is placed just before the instruction or situation in which
damage could occur.
vCaution: These statements indicate situations that can be potentially hazardous
to you. Acaution statement is placed just before the description of apotentially
hazardous procedure step or situation.
vDanger: These statements indicate situations that can be potentially lethal or
extremely hazardous to you. Adanger statement is placed just before the
description of apotentially lethal or extremely hazardous procedure step or
situation.
2BladeCenter HS20 Type 7981: Problem Determination and Service Guide

Features and specifications
The following table provides asummary of the features and specifications of the
HS20 Type 7981 blade server operating in anon-NEBS environment.
Note: Power, cooling, removable-media drives, external ports, and advanced
system management are provided by the BladeCenter unit.
Microprocessor:
Supports up to two Dual-Core Intel
®
Xeon Processor LV microprocessors
Note: Use the Configuration/Setup
Utility program to determine the type
and speed of the microprocessors in
your blade server.
Memory:
vDual channel 400 MHz (DDR2) with
4dual inline memory module
(DIMM) slots
vType: 2-way interleaved, DDR2,
PC3200, ECC SDRAM registered
x4 DIMMs
vSupports 512 MB, 1GB, 2GB, and
4GB DIMMs (as of the date of this
publication) for up to 16 GB of total
memory.
Drives: Support for two internal
small-form-factor Serial Attached SCSI
(SAS) drives
Integrated functions:
vDual-channel gigabit Ethernet
controller
vExpansion card interface
vATI Radeon 7000M video
controller
vLSI 1064 SSerial Attached SCSI
(SAS) controller
vLight path diagnostics
vLocal service processor (BMC)
vRS-485 interface for
communication with the
management module
vAutomatic server restart (ASR)
vSerial over LAN (SOL)
vIntelligent Platform Management
Interface (IPMI)
v4USB buses for communication
with keyboard, mouse, and
removable media drives
Predictive Failure Analysis
® (PFA)
alerts:
vMicroprocessor
vMemory
Electrical Input: 12 Vdc
Environment:
vAir temperature:
–Blade server on: 10° to 35°C (50°
to 95°F). Altitude: 0to 914 m
(2998.69 ft)
–Blade server on: 10° to 32°C (50°
to 90°F). Altitude: 914 mto 2133
m(3000 ft to 7000 ft)
–Blade server off: -40° to 60°C
(-40° to 140°F)
v
Humidity:
–Blade server on: 8% to 80%
–Blade server off: 5% to 80%
Size:
vHeight: 24.5 cm (9.7 inches)
vDepth: 44.6 cm (17.6 inches)
vWidth: 2.9 cm (1.14 inches)
vMaximum weight: 5.4 kg (12 lb)
Note: The operating system in the blade server must provide USB support for the
blade server to recognize and use the keyboard, mouse, and removable media
drives. The BladeCenter unit uses USB for internal communications with these
devices.
Chapter 1. Introduction 3

Blade server controls, LEDs, and connectors
This section describes the blade server control panel buttons and LEDs.
Note: The control panel door is shown in the closed (normal) position in the
following illustration. To access the power-control button, you must open the control
panel door.
KVM select button
Activity LED
Location LED
Information LED
Blade-error LED
Media-tray select
buttom
Power-control button
Power-on LED
KVM (keyboard/video/mouse) select button: Press this button to associate the
shared BladeCenter unit keyboard, video, and mouse ports with the blade server.
The LED on this button flashes while the request is being processed then is lit
when the ownership of the KVM has been transferred to the blade server. It can
take approximately 20 seconds to switch the KVM control to the blade server.
Using akeyboard that is directly attached to the management-module, you can
press keyboard keys in the following sequence to switch KVM control between
blade servers:
NumLock NumLock blade_server_number Enter
Where blade_server_number is the two-digit number for the blade bay in which
the blade server is installed.
If there is no response when you press the KVM select button, you can use the
management-module Web interface to determine whether local control has been
disabled on the blade server.
Note:
1. The operating system in the blade server must provide USB support for the
blade server to recognize and use the keyboard and mouse, even if the
keyboard and mouse have PS/2-style connectors.
2. If you install asupported Microsoft Windows operating system on the blade
server while it is not the current owner of the keyboard, video, and mouse, a
delay of up to 1minute occurs the first time that you switch the keyboard, video,
and mouse to the blade server. During this one-time-only delay, the blade server
device manager enumerates the keyboard, video, and mouse and loads the
device drivers. All subsequent switching takes place in the normal KVM
switching time frame (up to 20 seconds).
4BladeCenter HS20 Type 7981: Problem Determination and Service Guide