IBM Eserver 345 Series User manual

IBM xSeries 345
Type 8670
Option Installation Guide
SC88-P919-00
ERserver


IBM xSeries 345
Type 8670
Option Installation Guide
SC88-P919-00
ER s e r v e r


Note:
Before using this information and the product it supports, be sure to read the general information in
“Notices”, on page 45.
Second Edition (May 2003)
© Copyright International Business Machines Corporation 2003. All rights reserved.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.

Contents
Safety ............................v
Chapter 1. Introduction ......................1
Related publications .......................1
Notices and statements used in this book ...............2
Major components of the xSeries 345 Type 8670 server ..........3
System-board option connectors ...................4
PCI riser-card option connectors ...................4
System-board internal cable connectors ................5
System-board external port connectors ................6
System-board switches and jumpers .................7
System-board LED ........................9
Light Path Diagnostics panel ....................10
Chapter 2. Installing options ...................11
Installation guidelines ......................11
System reliability considerations .................11
Working inside the server with the power on .............11
Handling static-sensitive devices .................11
Server power features ......................13
Turning on the server .....................13
Turning off the server .....................13
Removing the cover and bezel ...................15
Working with adapters ......................16
Installing a ServeRAID-5i controller ................21
Installing a hot-swap drive .....................22
Installing memory modules ....................23
Installing a microprocessor ....................26
Installing a hot-swap power-supply option ...............31
Replacing a hot-swap fan .....................33
Replacing the battery ......................34
Completing the installation.....................36
Installing the server cover and bezel ................36
Installing the server in a rack...................36
Updating your server configuration.................36
Connecting external options ...................37
Cabling the server.......................37
Chapter 3. Input/output connectors ................39
Auxiliary-device (pointing device) connector ..............40
Ethernet connectors .......................40
Integrated system management processor (ISMP) interconnect ports .....40
Keyboard connector .......................40
Serial connector ........................41
Ultra320 SCSI controller system-board connectors ............41
SCSI cabling requirements ...................41
SCSI IDs ..........................41
SCSI connector .......................42
Universal Serial Bus version 1.1 connectors ..............42
Video connector ........................42
Appendix. Notices .......................45
Edition notice .........................45
© Copyright IBM Corp. 2003 iii

Trademarks ..........................46
Important notes.........................46
Product recycling and disposal ...................47
Electronic emission notices ....................47
Federal Communications Commission (FCC) statement .........47
Industry Canada Class A emission compliance statement ........48
Australia and New Zealand Class A statement ............48
United Kingdom telecommunications safety requirement.........48
European Union EMC Directive conformance statement .........48
Taiwanese Class A warning statement ...............49
Chinese Class A warning statement ................49
Japanese Voluntary Control Council for Interference (VCCI) statement . . . 49
Power cords ..........................49
Index ............................53
iv IBM xSeries 345 Type 8670: Option Installation Guide

Safety
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d’installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.
Antes de instalar este producto, lea la información de seguridad.
© Copyright IBM Corp. 2003 v

Läs säkerhetsinformationen innan du installerar den här produkten.
Statement 1
Danger
Electrical current from power, telephone, and communication cables is hazardous.
To avoid a shock hazard:
vDo not connect or disconnect any cables or perform installation, maintenance, or
reconfiguration of this product during an electrical storm.
vConnect all power cords to a properly wired and grounded electrical outlet.
vConnect to properly wired outlets any equipment that will be attached to this
product.
vWhen possible, use one hand only to connect or disconnect signal cables.
vNever turn on any equipment when there is evidence of fire, water, or structural
damage.
vDisconnect the attached power cords, telecommunications systems, networks, and
modems before you open the device covers, unless instructed otherwise in the
installation and configuration procedures.
vConnect and disconnect cables as described in the following table when installing,
moving, or opening covers on this product or attached devices.
To connect:
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
To disconnect:
1. Turn everything OFF.
2. First, remove power cords from outlet.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
Statement 2
CAUTION:
When replacing the lithium battery, use only IBM Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has a
module containing a lithium battery, replace it only with the same module type made
by the same manufacturer. The battery contains lithium and can explode if not
properly used, handled, or disposed of.
Do not:
vThrow or immerse into water.
vHeat to more than 100° C (212° F)
vRepair or disassemble
Dispose of the battery as required by local ordinances or regulations.
vi IBM xSeries 345 Type 8670: Option Installation Guide

Statement 3
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
vDo not remove the covers. Removing the covers of the laser product could result in
exposure to hazardous laser radiation. There are no serviceable parts inside the
device.
vUse of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
Danger
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the
following. Laser radiation when open. Do not stare into the beam, do not view directly with
optical instruments, and avoid direct exposure to the beam.
Statement 4
≥18 kg (39.7 lb) ≥32 kg (70.5 lb) ≥55 kg (121.2 lb)
CAUTION:
Use safe practices when lifting.
Safety vii

Statement 5
CAUTION:
The power-control button on the device and the power switch on the power supply do
not turn off the electrical current supplied to the device. The device also might have
more than one power cord. To remove all electrical current from the device, ensure
that all power cords are disconnected from the power source.
1
2
Statement 8
CAUTION:
Never remove the cover on a power supply or any part that has the following label
attached.
Hazardous voltage, current, and energy levels are present inside any component that
has this label attached. There are no serviceable parts inside these components. If you
suspect a problem with one of these parts, contact a service technician.
Statement 12
CAUTION:
The following label indicates a hot surface nearby.
viii IBM xSeries 345 Type 8670: Option Installation Guide

Statement 13
DANGER:
Overloading a branch circuit is potentially a fire hazard and a shock hazard under
certain conditions. To avoid these hazards, ensure that your system electrical
requirements do not exceed the branch circuit protection requirements. Refer to the
information that is provided with your IBM device for electrical specifications.
Statement 14
CAUTION:
Hazardous voltage, current, and energy levels might be present. Only a qualified
service technician is authorized to remove the covers where the following label is
attached.
Statement 15
CAUTION:
Make sure that the rack is secured properly to avoid tipping when the server unit is
extended.
Statement 16
CAUTION:
Some accessory or option board outputs exceed Class 2 or limited power source
limits and must be installed with appropriate interconnecting cabling in accordance
with the national electric code.
Safety ix

Statement 17
CAUTION:
The following label indicates moving parts nearby.
WARNING: Handling the cord on this product or cords associated with accessories
sold with this product, will expose you to lead, a chemical known to the State of
California to cause cancer, and birth defects or other reproductive harm. Wash
hands after handling.
ADVERTENCIA: El contacto con el cable de este producto o con cables de
accesorios que se venden junto con este producto, pueden exponerle al plomo, un
elemento químico que en el estado de California de los Estados Unidos está
considerado como un causante de cancer y de defectos congénitos, además de
otros riesgos reproductivos. Lávese las manos después de usar el producto.
xIBM xSeries 345 Type 8670: Option Installation Guide

Chapter 1. Introduction
This Option Installation Guide contains instructions for installing, removing, and
connecting optional devices that your server supports.
Related publications
In addition to this Option Installation Guide, the following documentation comes with
your server:
vUser’s Guide
This publication is in Portable Document Format (PDF) on the IBM
®
xSeries
Documentation CD. It contains general information about your server.
vInstallation Guide
This printed publication contains instructions for setting up your server and basic
instructions for installing some options.
vSafety Information
This publication is in PDF on the IBM xSeries Documentation CD. It contains
translated caution and danger statements. Each caution and danger statement
that appears in the documentation has a number that you can use to locate the
corresponding statement in your language in the Safety Information book.
vRack Installation Instructions
This printed publication contains instructions for installing your server in a rack.
vHardware Maintenance Manual and Troubleshooting Guide
This publication is in PDF on the IBM xSeries Documentation CD. It contains
information to help you solve problems yourself, and it contains information for
service technicians.
Depending on your server model, additional publications might be included on the
IBM xSeries Documentation CD.
Your server might have features that are not described in the documentation that
you received with the server. The documentation might be updated occasionally to
include information about those features, or technical updates might be available to
provide additional information that is not included in your server documentation.
These updates are available from the IBM Web site. Complete the following steps
to check for updated documentation and technical updates:
1. Go to http://www.ibm.com/pc/support/.
2. In the Quick path to a product field, type 8670 and click Go.
3. On the left side of the “xSeries 345 8670 support” page, click Online
publications.
4. From the Online publications by category menu, select the category of
publications you want to display.
© Copyright IBM Corp. 2003 1

Notices and statements used in this book
The caution and danger statements that appear in this book are also in the
multilingual Safety Information book, which is on the IBM xSeries Documentation
CD. Each statement is numbered for reference to the corresponding statement in
the Safety Information book.
The following notices and statements are used in the documentation:
vNotes: These notices provide important tips, guidance, or advice.
vImportant: These notices provide information or advice that might help you avoid
inconvenient or problem situations.
vAttention: These notices indicate potential damage to programs, devices, or
data. An attention notice is placed just before the instruction or situation in which
damage could occur.
vCaution: These statements indicate situations that can be potentially hazardous
to you. A caution statement is placed just before the description of a potentially
hazardous procedure step or situation.
vDanger: These statements indicate situations that can be potentially lethal or
extremely hazardous to you. A danger statement is placed just before the
description of a potentially lethal or extremely hazardous procedure step or
situation.
2IBM xSeries 345 Type 8670: Option Installation Guide

Major components of the xSeries 345 Type 8670 server
The orange color on components and labels in the server indicates hot-swap or
hot-plug components. You can install or remove these components while the server
is running, provided that the server is configured to support hot-swap and hot-plug
features.
The blue color on components and labels indicates touch points, where a
component can be gripped, a latch moved, and so on.
The following illustration shows the major components in the server.
Hot-swap fan
Air baffle
Microprocessor
Microprocessor
air baffle
PCI riser card
assembly
Memory module
System board
VRM
Filler panel for
drive bay
Hot-swap
power supply
Heat sink
Power supply
blank (some models) Shuttle
Chapter 1. Introduction 3

System-board option connectors
The following illustration shows the connectors on the system board for
user-installable options.
PCI-X slot 2
64-bit 3.3V
100 MHz
(J13)
PCI-X slot 1
64-bit 3.3V
100 MHz
(J14)
PCI riser
card
(J16)
DIMM 1
(J1) DIMM 3
(J3)
DIMM 4
(J4)
VRM 2
(J5)
VRM 1
(J8)
DIMM 2
(J2)
Microprocessor 2
(J6)
Microprocessor 1
(J7)
Battery
(BH1)
PCI riser-card option connectors
The following illustration shows the connectors on the PCI-riser card for
user-installable options.
PCI-X slot 3 64-bit
3.3V (PCI 3)133 MHz
PCI-X slot 4 64-bit
3.3V 133 MHz (PCI 4)
PCI slot 5 32-bit
5V 33 MHz (PCI 5)
System management connector
4IBM xSeries 345 Type 8670: Option Installation Guide

System-board internal cable connectors
The following illustration shows the internal connectors on the system board.
Fans 4 and 8
(J28)
Fans 3 and 7
(J27)
Fans 2 and 6
(J29)
Fans 1 and 5
(J26)
Power
(J24)
USB 3
operator panel
Internal SCSI
(J23)
IDE (J21) Operator panel
(J22)
Power signal
(J25)
Chapter 1. Introduction 5

System-board external port connectors
The following illustration shows the external input/output connectors on the system
board.
Serial/video
(J9)
Mouse/keyboard
(J10)
Ethernet 1
(J11)
Ethernet 2
(J12)
USB 1
(J17)
USB 2
(J18)
External
SCSI
(J19)
RS485-A and B
(J15)
6IBM xSeries 345 Type 8670: Option Installation Guide

System-board switches and jumpers
The following illustration shows the switches and jumpers on the system board.
Flash boot block
recovery jumper
(J34)
System board
switch block
(SW2)
8 7 6 5 4 3 2 1
SW2
ON
Chapter 1. Introduction 7

Table 1 describes the function of each switch on the switch block.
Table 1. Switches 1-8
Switch
number Default value
Switch
description
8 Off Reserved.
7 Off Reserved.
6 Off Reserved.
5 Off Reserved.
4 Off Reserved.
3 Off Power-on override. When toggled to On, this switch forces the power on, overriding
the power-on button.
2 Off Power-on password override. Changing the position of this switch bypasses the
power-on password check the next time the server is turned on and starts the
Configuration/Setup Utility program so that you can change or delete the power-on
password. You do not need to move the switch back to the default position after the
password is overridden.
Changing the position of this switch does not affect the administrator password check
if an administrator password is set.
See the User’s Guide on the IBM xSeries Documentation CD for additional
information about the power-on password.
1 Off H8 out serial port. This switch is reserved for service use only.
Notes:
1. Before changing any switch settings or moving any jumpers, turn off the server;
then, disconnect all power cords and external cables. (Review the information in
“Safety” on page v, “Installation guidelines” on page 11, “Handling static-sensitive
devices” on page 11, and “Turning off the server” on page 13.)
2. Any system-board switch or jumper blocks that are not shown in the illustrations
in this book are reserved.
8IBM xSeries 345 Type 8670: Option Installation Guide