Ice-O-Matic Hotel Dispenser CD 40030 Series User manual

®
CD 40030 Series
Hotel Dispenser
CD 40030
✓Stores 180 lbs. (81 Kgs.) of ICE
✓Constructed from sturdy, corrosion-resistant
300 series stainless steel
✓ Only 30 inches (762 mm) wide
✓ Available with water glass filler and
coin/token options
ICE-O-Matic ®is the Best ICE Making Solution for:
Hard Water, Food Safety and Tight Spaces
Problem
Power Clean
Allows access to the bin for easy cleaning
without moving the ICE machine. Interlock safety
switch turns off machine agitation when top-front
access panel is removed.
Simple Operation
• Turbo Dispense - dispenses a 1/4 lb. of ICE per second
• Push to Dispense - user friendly dispensing
• Smudge Proof Finish - prevents fingerprints
and smudges
Solution
Hard To Clean
Ice machine must be lifted off of
other dispensers for cleaning
Difficult Dispensing
Ice is sometimes slow and difficult
to dispense
Ice Melts Too Fast
Inadequate storage insulation
causes Ice to melt too quickly
Maximum Preservation
Hotel Dispenser is insulated with an average of 4
inches of foam for maximum ICE preservation
Tight-Fitting Spaces
Vending area utilization
Maximum ICE
Maximum ICE storage in a minimum amount
of space with an ultra-low profile

Dimensions and Air Flow
CD 40030 Push 180 (81) 115/60/1 2 2.1 15 220 (99)
CD 40130 Push / Water 180 (81) 115/60/1 2 2.1 15 224 (101)
CD 40230 Coin/Token 180 (81) 115/60/1 2 2.1 15 220 (99)
CD 40530 Push 180 (81) 230/50/1 2 2.1 15 220 (99)
Note #1: Model CD40030 and CD40530 dispensers accept all 30” ICE Series™ Cube ICE Makers
Note #2: Water dispensers and coin / token mechanisms cannot be field installed on the CD 400 Series Dispensers
Note #3: CD400 Series Dispensers cannot have a water dispenser and coin / token mechanism on the same machine
Note #4: CD40030 and CD40530 Series units do not require an Adaptor and Bin Level Kit
Options:
TKNS: 500 tokens for use with CD40230, 984” diameter.
ICE-O-Matic’s® machines are not designed for outdoor installations. ICE-O-Matic®remote condensers are designed for outdoor installations.
Machine requires voltage indicated on rating name plate. Failures caused by improper voltage are not considered factory defects. Extended
periods of operation at temperature exceeding limitations constitutes misuse under the terms of ICE-O-Matic®Manufacturer’s Limited Warranty,
resulting in a loss of warranty coverage.
Model Dispenser Bin Storage Voltage Min. Circuit Maximum Shipping
No. Operated by: Applied Capacity* Characteristics No. of Wires Ampacity Fuse Size Weight lbs. (Kgs.)
ORDERING AND SPECIFICATION INFORMATION
Air out
(top discharge)
Air out
(side discharge)
Air in-rear of
ICE Maker
53.25"
(1351 mm)
30"
(762 mm)
24"
(610 mm)
33.5"
(851 mm)
CD 40030 Series Hotel Dispenser
60 Hz50 Hz
Air-Cooled lbs. (kgs.) 320 (145) 157 (346) 506 (230) 235 (370) 625 (284)
Water-Cooled lbs. (kgs.) 351 (160) 154 (338) 528 (240) 257 (566) 567 (258)
Remote-Cooled lbs. (kgs.) n/a n/a n/a n/a 591 (269)
Voltage Char. 115/60/1 230/50/1 115/60/1 230/50/1 115/60/1
1. Tested at 70º Air/50º Water.
2. All specifications and performance data are subject to normal manufacturing variances.
Model ICE 0250 ICE 0305 ICE 0400 ICE 0405 ICE 0500
ICE PRODUCTION FOR OPTIONAL CUBE ICE MAKERS — POUNDS (KILOGRAMS) PER 24 HOURS
30"
762.4
10"
WATER VALVE
(WATER FILLER
254.8
6"
152.4
53 1/4"
1351.3
ICE FILL STATION
8 3/4 [221.5] HIEGHT
13 1/2 [342.9] WIDTH
8 1/2 [215.9] DEPTH
POWER
CORD
17 3/4"
451.1 1"
24.1
7 1/2"
189.4
7"
179.1
7 1/2"
189.7
17 1/2"
444.4
WATER INLET
3/8 FLARE
(WATER FILLER ONLY)
3/4 FPT
DRAIN
(2) 5/16-18 UNC
ICE HEAD
24"
609.6
25 5/8"
650.5
33 1/2"
849.4
ICE-O-Matic 11100 E. 45th Avenue, Denver, CO 80239
Tel. [phone] Fax. [phone] www.iceomatic.com
We reserve the right to make changes in design and construction at any time
without obligation.
2004 © ICE-O-Matic Rev Code: 4006A - 011/03-SS
I
S
O
9
0
0
1
C
E
R
T
I
F
I
E
D
®
OPERATING LIMITS
Ambient Temp. Range
Air & Water 50° - 110°F (10° - 43°C)
Water Temp. Range 40° - 100°F (4.5° - 38°C)
Water Pressure Ice Maker Min. 20 psi (1.4 bar)
Water in Max. 60 psi (6.9 bar)
Condenser Inlet Water Min. 20 psi (1.4 bar)
(Water cooled only) Max. 60 psi (6.9 bar)
20"
(508 mm)
Half Cube
7/8" x 7/8" x 3/8"
(22mm x 22mm x 10mm)
Full Cube
7/8" x 7/8" x 7/8"
(22mm x 22mm x 22mm)