Ice-Tech 50C-CD 55 User manual

MODELS / MODELOS
50C-CD 55
85C-CD 90
135C-GR 140
150
200/175-GR 220
400/355
550/475-GR 560
G550-GR 560S
110 0
G110 0
USER MANUAL
MANUAL DEL UTILIZADOR

USER MANUAL
MANUAL DEL UTILIZADOR

5
ENGLISH
55
THIS MANUAL IS PART OF THE PRODUCT. READ IT CAREFULLY IN ORDER
TO USE AND MAINTAIN THE EQUIPMENT CORRECTLY. IT IS IMPORTANT TO
KEEP IT FOR FUTURE TROUBLESHOOTING AND REFERENCE.
WARNING
The installation of this equipment should be done by the Technical Assistance Service department.
The inlet jack should always be placed on an accessible location.
ALWAYS disconnect the power supply from the machine BEFORE any cleaning or maintenance service.
Any change needed on the electrical installation for the appropriate connection of the machine, should be
exclusively performed by qualied and certied professional personnel only.
Any use by the ice maker not intended to produce ice, using drinking water, is considered inappropriate.
It is extremely dangerous to modify or intend to modify this machine, and shall make any type warranty
void.
This machine should not be used by children or handicapped without the proper supervision and
monitoring.
Children should be monitored to assure that they should not play near the equipment.
This machine is not intended to be used outdoors nor exposed to the rain.
Connect the equipment to the drinking water network.
The machine should be connected using the power cable supplied with the equipment. The connection is
not intended for xed cabling.
IT IS MANDATORY TO GROUND THE EQUIPMENT.
To avoid possible discharges on individuals or damages to the equipment, the
machine should be grounded pursuant local and/or national regulations as the
case may be.
THE MANUFACTURER SHALL BE HELD HARMLESS IN CASE OF DAMAGES
ARISING DUE TO THE LACK OF THE GROUND INSTALLATION.
In order to assure the proper operation and efciency of this equipment, it is of paramount importance to
follow the recommendations of the manufacturer, SPECIALLY THOSE RELATED TO CLEANING AND
MAINTENANCE OPERATIONS, which should be performed mostly by qualied personnel only.
CAUTION:
Do not try to perform repairs. The intervention of non-qualied personnel, besides of being dangerous,
could result in serious malfunctioning. In case of damages, contact your distributor. We recommend to
always use original replacement and spare parts.
Perform all discharge and recovery of materials or waste according the national regulations in force.

ENGLISH
66
RECEPTION OF THE MACHINE
Inspect the outside packing. In case of damages, MAKE THE CORRESPONDING CLAIM TO THE
CARRIER.
To conrm the existence of damages, UNPACK THE MACHINE IN THE PRESENCE OF THE CARRIER and
state any damage on the equipment on the reception document, or on a separate instrument. As from May
1, 1998, we complie with the European regulations on management of packing and packing waste, inserting
the “Green Dot Label” on all their packages.
Always state the machine number and model. This number is printed on four locations:
1. PACKING
On the outside, it contains a label with the manufacturing number (1).
2. EXTERIOR OF THE EQUIPMENT
On the back of the equipment, there appears a label
with the same characteristics as the previous one (1).
3. NAMEPLATE
On the back of the machine.
Check that in interior of the machine the
installation kit is complete and comprises:
- Ice scraper, ¾ gas pipe, lters and manual.
- 22 mm drain hose in models 45 and 85
and in water cooled machines
- In some models, shims are included.
- Warranty and serial number.
CAUTION: ALL PACKING ELEMENTS (plastic bags, carton boxes and wood pallets)
SHOULD BE KEPT OUTSIDE THE REACH OF CHILDREN, AS THEY ARE A SOURCE
OF POTENTIAL HAZARD.
INSTALLATION
THIS ICE MAKER IS NOT DESIGNED FOR OUTDOOR OPERATION.
An incorrect installation of the equipment may cause damages to individuals, animals
or other materials, being the manufacturer not responsible for such damages.
CAUTION:
The machines are designed to operate at room temperature between 5ºC (41ºF) and 43ºC (109.40ºF), with
inlet water temperature between 5ºC (41ºF) and 35ºC (95ºF).
The reduction motor is excessively forced if operated under the minimum temperatures. Above the
maximum temperature, the life of the compressor is shortened and the production is substantially less.
Do not place anything over the maker or facing the front louver.
(1)

7
ENGLISH
7
In case the front louver is not enough, the exit is either total or partially obstructed or due to its placement
it will receive hot air from another device, we recommend, in case it is not possible to change the location
of the machine, TO INSTALL A WATER CONDENSER.
IT IS IMPORTANT THAT THE WATER PIPING DO NOT PASS BY OR NEAR SOURCES
OF HEAT SO AS NOT TO LOSE ICE PRODUCTION.
THREAD THE SUPPORT LEGS TO THE BASE OF THE MACHINE ON THE
HOUSING SET TO SUCH END AND REGULATE THE HEIGHT AS TO HAVE THE
EQUIPMENT PERFECTLY LEVELED.
IN MODULAR MACHINES
Base jack
Bib
Discharge hose
Water connection hose
Jack
Ventilation louver
>10 cm
>4''
Jack Base jack
Bib
Silo drainage
Water connection hose
Condenser discharge outlet
>10 cm
>4''

ENGLISH
8
1. WATER AND DRAINAGE
Water quality has a remarkable inuence on the appearance,
hardness and avor of the ice as well as, on the machines
condensated by water, on the life of the condenser.
2. CONNECTIONS TO THE WATER
NETWORK
Use a exible pipe (1.3 m – 4.27 feet length) with the two lter
joints supplied with the machine. We strongly discourage the
use of two-exit bibs and two switches as, due to an error
could close that back one, leaving the machine without water
supply. This could result on a damage call without actually
existing one.
Pressure should be established between 0.7 and 6 Bar (10 /
85 psi.)
If pressures overpass such values, install the necessary
corrective devices.
INSTALL A 10 µ PARTICLE FILTER INCLUDED IN THE
KIT.
3. CONNECTION TO DRAINAGE
Drainage should be located lower to the machine level, at 150 mm (5.91 inches) minimum.
It is convenient that the drainage pipe is of 30 mm (1.18 in) of interior diameter and with a
minimum gradient of 3 cm (1.18 in) per meter (see gure).
CORRECT INCORRECT
INCORRECT
Descending Ascending

9
ENGLISH
4. ELECTRICAL CONNECTION
IT IS MANDATORY TO GROUND THE EQUIPMENT.
To avoid possible discharges on individuals or damages to the equipment, the
machine should be grounded pursuant local and/or national regulations as the
case may be.
THE MANUFACTURER SHALL BE HELD HARMLESS IN CASE OF DAMAGES
ARISING DUE TO THE LACK OF THE GROUND INSTALLATION.
The machine is supplied with a 1.5 m (4.92 feet) cable of length. In case the supply cable is damaged, it should
be replaced by a cable of special assembly to be furnished by the manufacturer or post-sale service. Such
replacement should be performed by qualied technical service only.
The machine should be places in such a way as to allow a minimum space between the back and the wall to
allow an easy access and without risks to the cable jack.
Safeguard the base of the jack.
It is convenient to install adequate switches and fuses.
The line up to the jack should have a minimum section of 2.5 mm2 (0.0038 in2)
Voltage and tension are indicated in the nameplate and on the technical specications
of this manual. Variation on voltage above the 10% stated on the nameplate could
result on damages or prevent the machine start-up.
5. INSTALLATION OF MODULAR EQUIPMENTS OVER DEPOSITS OR SILOS
Modular makers should be installed over deposits
or silos, following the instructions contained in this
manual.
The resistance and stability of the
container-machine/s assembly should be veried,
as well as the fastening elements.
6. ASSEMBLY OF THE DISPERSION CONE
(MODULAR MODELS)
This device distributes the ice in the silos, and
avoids ice compression under the exit pipe.
Changing its position, the ice could be directed to
any direction.

ENGLISH
10
7. WATER LEVEL
The function of the water level is to maintain the necessary ow on the evaporator, and using the magnetic
micro device incorporated, stop the operation of the machine until the water reaches again the container.
The models 400, 550 and 1100 have a water pressostat replacing the micro-magnetic.
The optimum level is located on the horizontal indicated in the gure, and its regulation is made following
the indications appearing below.
START-UP
1. Previous Checkup
a) Is the machine leveled?
b) Voltage and frequency are the same as those on the nameplate?
c) Are the discharges connected and operating?
d) ** If air condensed: Is the air circulation and its temperature appropriate?
e) ** Is water pressure appropriate?
NOTE: In case input water pressure is higher that 6 Bar (85 psi), install a pressure reducer. THE BIBB
CONNECTION PRESSURE SHOULD NEVER BE REDUCED.
FLOAT VALVE REGULATION
FLOAT
PROBE
SAFETY OVERFILL Turn upwards to increase the level,
and downwards to decrease it.
(Grab from the metallic arm, NEVER
FROM THE FLOAT)
ROOM WATER
MAXIMUM 43ºC / 109,40ºF 35ºC / 95ºF
MINIMUM 5ºC / 41ºF 5ºC / 41ºF
MINIMUM 0,7 Bar (10 psi)
MAXIMUM 6 Bar (85 psi)

11
ENGLISH
2. Start-up
Once the installation instructions are followed (ventilation, site conditions, temperatures, water quality,
etc.), proceed as follows:
1. In the case of modular modules, remove the cover to access the installation kit (lters, connection hoses,
dispersion cones, etc.).
2. In case of compact models, open the deposit door to access the installation kit.
3. Open the water inlet. Verify the existence of leakages.
4. Connect the machine to the electrical network.
5. Verify that there are no vibrations or frictions on the elements.
6. After the 10 minutes of the timer installed in the electric panel, the machine will start the operation.
7. In the case of modular models (mainly in three-phase equipments), having the cover removed, verify that
the motor is rotating in the correct direction.
8. Verify that after 15 minutes, the frost on the aspiration pipe is at 20 mm (0.78 in) of the compressor.
CAUTION:
INSTRUCT THE USER ABOUT MAINTENANCE, INFORMING THAT
MAINTENANCE AND CLEANING OPERATION AS WELL AS DAMAGES
DUE TO THE LACK OF SUCH OPERATIONS: ARE NOT INCLUDED ON THE
WARRANTY.
The technical installer shall invoice traveling costs, hours and materials used on such operations.
MAINTENANCE AND CLEANING INSTRUCTIONS
CAUTION: Maintenance and cleaning operations and damages as the lack of those activities: Are not
included on the warranty.
If a good maintenance is performed, the machine will continue producing a good quality ice and will be free
of damages.
Maintenance and cleaning intervals will depend on the conditions of the location and water quality.
CAUTION: At least, one revision and cleaning should be performed every six months.
On dusty environments, it might be necessary to clean the condenser on a monthly basis.
MAINTENANCE AND CLEANING PROCEDURES:
** CAUTION: For all cleaning and maintenance operations: Disconnect the machine from the power
supply.

ENGLISH
12
1. Water condenser
1. Disconnect the machine.
2. Disconnect the water inlet or close the bibb.
3. Disconnect the water inlet and outlet from the condenser.
4. Prepare a solution at the 50% of phosphoric acid and distilled or demineralized water.
5. Make the solution circulate through the condenser. (The solution is more effective if hot – between 35ºC
[95ºF] and 40ºC [104ºF]).
DO NOT USE HYDROCHLORIC ACID.
2. Air Condenser
1. Disconnect the machine.
2. Disconnect the water inlet or close the bibb.
3. Clean the louvered area with the help of an aspirator with a brush, non-metallic brush or low-pressure
air.
3. Cleaning the Stock Container (Compact models)
1. Disconnect the machine, close the water and empty the ice-cube stock.
2. Use a dishcloth and bleach with detergent.
4. Exterior Cleaning
Use the same procedure as the one indicated for the container.
5. Cleaning of the Inlet Filters
They are easily obstructed during the rst days of operation, MAINLY WITH NEW PIPING
INSTALLATIONS.
Loose the hose and clean it under water.
6. Water Leak Control
When working on the machine, always check the water connections, status of the clamps and hoses with
the purpose of avoiding leakages and prevent damages or oods.

133
PANELES DE CONTROL / CONTROL PANEL
1. MODELO 45-CD50 / MODEL 45-CD50
Piloto verde: Indica que la máquina está activada. Puede estar parada por termostato de stock.
Pulsador negro: Pone la máquina en funcionamiento. También rearma la máquina cuando está parada por
algún elemento de seguridad.
Pulsador rojo: Para la máquina completamente.
Green Led: Indicates that the machine is activated. Might be stopped due to the bin thermostat
Black Switch: Starts the operation of the machine. Also rearms the machine when it is stopped by some
security element.
Red Switch: Stops the machine completely
Piloto verde
Green Led
Pulsador negro
Black Switch Pulsador rojo
Red Switch
2. MODELO 85-CD90 / MODEL 85-CD90
Pulsador verde: Pone la máquina en funcionamiento indicándonoslo con el piloto encendido.
Piloto rojo: Nos indica que la máquina está parada por algún elemento de seguridad
Piloto naranja: Nos indica cuando el almacén de hielo está lleno.
Green Switch: Starts the operation of the machine. It is indicated with the led on.
Red Led: Indicates that the machine is stopped by a security element.
Orange Led: Indicates that the storage bin is full of ice.
Piloto naranja
Orange Led
Piloto rojo
Red Led Pulsador verde
Green Switch

134
ESQUEMAS ELéCTRICOS / WIRING DIAGRAM
45-CD50
26/05/2008 plano: 24/10
Negro/Black
(2)
(1)
Ew
Gris/Grey
Rojo/Red
Violeta/Violet
Azul/Blue
N
13
14
Ts
9
58
12
L
C
V
Pv
R S
Iw
-LED Verde linea K
Pt.- Protector térmico motor
-Electroválvula condensaciónEw.
-Interruptor de paroIs.
-Presostato ventilador
S.
-Ventilador
Pv.
V.
-Interruptor de marcha
-Paro por llenado
-Micro boya falta de agua
-Motorreductor
-Presostato de seguridad
R.
Ts.
Iw.
Ir.
Ps.
-Compresor
K- LED Green on
-Motor thermal protectionPt.
-Condenser water valveEw.
-Off switchIs.
-Fan pressostat
S.
-Fan
Pv.
V.
-High pressure safety pressostat
-Full storage bin stop
-Water low level float switch
-On switch
-GearmotorR.
Ts.
Iw.
Ir.
Ps.
-Compressor
Is
Marrón/Brown
KIr
Ps
Pt
L

135
85-CD90
-Fan pressostat (only air cooled models)
-High pressure safety pressostat
-Termico Motorreductor/Thermic gearmotor
22
L
V. -Fan
-VentiladorV.
-Condenser water valveEw.
-Electroválvula condensaciónEw.
-Compressor
Ip.
Ts.
-On/off switch
-Full storage bin stop
S.
-Compresor
-Paro por llenado
-Interruptor de paro-marchaIp.
Ts.
S.
Ps.
R. -Gearmotor
Pt.
-Presostato de seguridad
-Motoreductor
Ps.
R.
-Micro boya falta de aguaIw. Iw.- Water low level float switch
04/10/2010 plano:24/10
III
I
II
-Verde linea / Green on
-Ambar llenado/ Yellow full
-Motor thermal protection
Pt.- Protector térmico motor
L
2
A
1
A
Tem.
Marrón/brown
Rojo/red
Ps
Iw
L
Gris/Grey
C
Pt
Ts
Pv.
C1
Tem.
-Contactor
-Start timer-Temporizador a la conexion
-Contactor
-Presostato ventilador (sólo cond.por aire)Pv.
C1
Tem.
3
LL
L12
L
3
T
T
1
97
2
T
98
A1
c1
95
A96
2
II
Gris/Grey
Violeta/Violet Violeta/Violet
Violeta/Violet
Marrón/brown
N
Ip
IIII
Azul/Blue
Marrón/brown
(2)
Ew
Negro/Black
Pv
C
L
V
4
4
a1
C
3

136
MONOFÁSICA / MONOPHASE
-Motor thermal protectionPt.
Pt.
01/02/2011 plano: 24/10
-Protector térmico motor
-High pressure safety pressostat
-Water pressostat (IQ400/550-GR560S)
/Red
Rojo
White
Blanco/
-Fan pressostat (only air cooled models)
-Circuit Breaker (motorgear)
-Water low level float switch
Azul/Blue
Ps.
-Presostato de seguridadPs.
A2
S
Rojo/Red
Yellow
Full
1
3
L
T21 LL
1Rojo/Red
Pt
(1) Red
Water
Iw-Pw
2
ACL
Ps
Rojo
Marrón/Brown
Agua
CDis.
Gris/
4
2
Violeta/Violet
Ambar
Llenado
Grey
St
T3
R
T2
T1T
2
T3
C
Tem.
V
C.
L
-Start timer
-Contactor
Dis.
Pv.
c.
3
2
c
St.
Iw.
S.
Ip.
V.
Pw.
R.
-Fan
-Feedback contact
-Contact (Compressor)
-Compressor
-On/off switch
-Full storage bin stop
-Gearmotor
c1-contact (gearmotor)
Pv
L
1
A
1
c
1
Azul/Blue
L
2
2c
3
3c
L
Negro/Black
Tem.
C.
Pv.
c
c.
Dis.
2
3
St.
Iw.
S.
V.
Ip.
R.
Pw.
c1
-Ventilador
-Compresor
-Contactor
(1)SÓLO EN LA IQ550-GR560S / ONLY IQ550-GR560S
-Temporizador a la conexion
-Contacto (Motorreductor)
-Presostato ventilador (solo cond.por aire)
-Disyuntor (Motorreductor)
-Contacto (Compresor)
-Contacto autoalimentacion
-Paro por llenado
-Micro boya falta de agua
-Interruptor de paro-marcha
-Motoreductor
-Presostato de agua (IQ400/550-GR560S)
Negro/Black
1
A
Tem.
Azul/Blue
Azul/Blue
N
Breaker
Disyuntor
Ip
Marrón/Brown
Marrón/Brown
Marrón/Brown
L1
2
45
1
Blue
on
Azul
linea

137
400/550-GR560 R404A TRIFÁSICA / 400/550-GR560 R404A TRIPHASE
-Termico compresor/Thermic compressor -Detector de fase/Phase sequence relay -Ambar llenado/ Yellow full -Azul linea / Blue on -Fase cambia/Phase sequence -Contacto auxiliar autoalimentacion/Auxiliar contact feedback -Termico Motorreductor/Thermic gearmotor
-Protector térmico motor/Motor thermal protection -Motoreductor/Gearmotor -Condensador filtro/Electrical interference filter (capacitador)
R. L. II IV III V
2
Ca DF.
1
Ca I Pt.
-Temporizador a la conexion/Start Timer -Compresor/Compressor -Interruptor de paro-marcha/On-off switch -Paro por llenado/Full storage bin stop -Presostato ventilador (sólo cond.por aire)/Fan Pressostat (only air cooled models) -Contactor (Motorreductor)/Contact (Gearnotor) -Contactor (Compresor)/Contact (Compressor) -Micro boya falta de agua/Water low level float switch
-Presostato de seguridad/High pressure safety pressostat
Tem.
-Ventilador/Fan
Iw. Ip. Ps. St. c1
V.
2
c S. Pv. Pw.- Presostato de agua/Water pressostat
01/02/2011
1.3 A 3.6 A
REGULACION TERMICOS
MOTORREDUCTOR GEARMOTOR COMPRESOR COMPRESSOR
OVERLOAD SETTING
Rojo/Red
Marrón/Brown
Marrón/Brown
Marrón/Brown
Negro/Black
Negro/Black
Gris/Grey
Violeta/Violet
Negro/Black
Marrón/Brown
Violeta/Violet
Negro/Black Azul/Blue
Rojo
Agua Red
Water
Marrón/Brown
Rojo/Red
Negro/Black
Marrón/Brown
Negro/Black
Rojo/Red
-Contacto auxiliar autoalimentacion/Auxiliar contact feedback
2
1T2
S
T3
T
R
2
Ip
S T N
III
St 4
1 C
11
T
SR
14 12
DF V
Iw-Pw
L
(1)
IV
Ps
98
96
I1
LL2
97
L363/NO
Ca1
14/22
c
Pt
Tem.
1
c
2
A
1
A95
A2
A1
T3
T2
RV
1
T
II
C
98
96
2
A
195
A
Pv
L23
L
a2
C
63/NO 14/22 LL
97
L1
54 21

138
GENERADOR 550-GR560S / GENERATOR 550-GR560S
-Temporizador a la conexion / Start timer
-Solenoide de líquido / Liquid valve
-Interruptor de paro-marcha / On-off switch
-Contactor (Motorreductor) / Contact (gearmotor)
-Temporizador retardo solenoide / liquid valve timer
T1
Ip.
c1
T2
SL.
-Paro por llenado / Full storage bin stop
St.
-Micro boya falta de agua / Water low level float switch
Iw.
Pw.- Presostato de agua / Water pressostat
01/02/2011 plano: 24/10
-Termico Motorreductor / Thermic gearmotor
-Ambar llenado / Yellow full
-Fase cambia / Phase sequence
-Azul linea / Blue on
IV
II
III
I
-Protector térmico motor / Motor thermal protection
-Contacto auxiliar motorreductor / Auxiliar contact gearmotor
-Detector de fase / Phase sequence relay
DF.
1
Ca
R. -Motoreductor / Gearmotor
Pt.
V-Rojo: agua / Red:Water
NAzul/Blue
T2
18
2
AIV
SL
15
A1
T
Pt
Rojo/Red
12
11
R
DF
S
14
T
S
RNegro/Black
Negro/Black
Marrón/Brown
Verde/Green
Marrón/Brown
Negro/Black
Negro/Black
R
98
96
3
T1
T
T2
3
1
c
2
A
197
A95
1
2
LL
L
II
Iw-Pw V
Gris/Grey
St
4
Violeta/Violet
63/NO
Ca1
14/22
1
2
2
A
1
A
T1
III
4
5
1
2
Ip
I

139
1100 R404A TRIFÁSICA / 1100 R404A TRIPHASE
II
II
Negro/Black
Negro/Black
Negro/Black
Negro/Black
Negro/Black
Negro/Black
IV
L12
L3
L3
V
11
Tem.
1
A
IV R S
DF
TA
2
1
A
1 2
T
TT
3
12
T
TT
3
S
L2
L1
Ca2
L3
4 3
Rojo/Red
Rojo/Red
LL
4
1
Ca
St
St
1
Marron/Brown
1
2
1
96 98
Gris/Grey
Violeta/Violet
White
Marron/ Brown
Blanco/
L C
Ps
2
2
c
III
2
1
95
A
97
A
96 98
Blanco/
White
Gris/Grey
CL
Violeta/Violet
2
Iw
14
A2
95 97
1
c
12
Rojo/Red
3
L2L3
T
23
T
L
L
T
23
T
III
2
Ca
3 4
S
2
L3
L
Ps
Rojo/Red
Rojo/Red
4
1
Ca
Rojo/Red Azul/Blue Negro/Black Marron/Brown
1
L
Tem.
N T S R
A1
1
A
A
2
IT
98
1
96
1
T
97
1
L
95
96 98
2
c
A
A
1
2
Rojo/Red
97
95
A2
1
c
V
C
Pv
Ip Pt
Ip
R
Marron/ Brown
Marron/Brown
Pv
C
V
R
Pt
Tem. -Temporizador a la conexion / Start timer c1-Contactor (motorreductor) / Contact (gearmotor)
c2-Contactor (compresor) / Contact (compressor) Pv. -Presostato ventilador (solo cond.por aire) / Fan pressostat (only air cooled) V. -Ventilador / Fan S. -Compresor / Compressor Ip. -Interruptor de paro-marcha / On-off switch St. -Paro por llenado / Full storage bin stop Iw. -Presostato falta de agua /Water low pressure switch Ps. -Presostato de seguridad / High pressure safety pressostat R. -Motorreductor / Gearmotor
L. -Condensador filtro / Electrical interference filter (capacitador) Pt. -Protector térmico motor / Motor thermal protection DF. -Detector de fase / Phase sequence relay Ca1-Contacto auxiliar motorreductor / Auxiliar contact gearmotor
Ca2-Contacto auxiliar autoalimentación / Auxiliar contact feedback I -Térmico compresor / Thermic compressor II -Térmico motorreductor / Thermic gearmotor III -Verde línea / Green on IV -Ambar llenado /Yellow full V -Fase cambia / Phase sequence 15-09-08
3.6 A
REGULACION TERMICOS
OVERLOAD SETTING
COMPRESOR / COMPRESSOR
1.3 A
MOTORREDUCTOR / GEARMOTOR

140
GENERADOR 1100 / GENERATOR 1100
Azul/Blue
IV
R
N
1
A
SL
A2
T2
15
18
Azul/Blue
IV
18
15
2
A
SL
A1
R
T2
Marron/Brown
23
1
LT1
2
L
L3
Negro/Black
Negro/Black
Violeta/ Violet
V
Iw Ip
1
A
a1
4C
Marron/
Brown
Negro/
Black
Negro/
Black
96 98
T
1
2
T
T
3I
95 97 2
A
S T
c
A
1
1
Pt
A
R
T1
2
A3
Pt
3
LL2L1
V
Iw
1
Gris/Grey
1
St
24
Blanco/ White
12
R
DF
TS
14
11
1
A
cC
4
a1
98
96
Marron/
Brown
3
TT
21
T
Negro/
Black
Negro/
Black
197
95
Gris/Grey
4
2
III
IIII
St
T1
Violeta/ Violet
Ip
1
A
I
2
A
13-12-08
T1-Temporizador a la conexion / Start timer
T2-Temporizador válvula líquido / Liquid valve timer Pt-Protector térmico motor / Motor thermal protection Ip.-Interruptor de paro-marcha / On-off switch
St.-Paro por llenado / Full storage bin stop Iw.-Micro boya falta de agua / Water low level float switch R.-Motorreductor / Gearmotor
DF.-Detector de fase / Phase sequence relay Ca1-Contacto auxiliar motorreductor / Auxiliar contact gearmotor
I-Verde línea / Green on
II-Ambar llenado / Yellow full III-Fase cambia / Phase sequence IV-Térmico motorreductor/ Thermic gearmotor V-Agua / Water


141

142