Icom UR-FR5000 User manual

ABOUT CE AND DOC
Hereby, Icom Inc. declares that the
versions of UR-FR5100 and UR-
FR6100 which have the “CE” symbol
on the product, comply with the
essential requirements of the Radio Equipment
Directive, 2014/53/EU, and the restriction of the
use of certain hazardous substances in
electrical and electronic equipment Directive,
2011/65/EU. The full text of the EU declaration
of conformity is available at the following
internet address:
https://www.icomjapan.com/support/
DISPOSAL
The crossed-out wheeled-bin symbol
on your product, literature, or
packaging reminds you that in the
European Union, all electrical and
electronic products, batteries, and
accumulators (rechargeable
batteries) must be taken to designated collection
locations at the end of their working life. Do not
dispose of these products as unsorted municipal
waste. Dispose of them according to the laws in
your area.
FCC INFORMATION
This equipment has been tested and found
to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when
the equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and,
if not installed and used in accordance with
the instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely
to cause harmful interference in which case the
user will be required to correct the interference
at his own expense.
CAUTION: Changes or modications to this
transceiver, not expressly approved by Icom
Inc., could void your authority to operate this
transceiver under FCC regulations.
VOICE CODING TECHNOLOGY
The AMBE+2™ voice coding Technology
embodied in this product is protected by
intellectual property rights including patent
rights, copyrights and trade secrets of Digital
Voice Systems, Inc. This voice coding
Technology is licensed solely for use within this
Communications Equipment.
The user of this Technology is explicitly
prohibited from attempting to extract, remove,
decompile, reverse engineer, or disassemble
the Object Code, or in any other way convert
the Object Code into a human-readable form.
U.S. Patent Nos.
#8,595,002, #8,359,197, #8,315,860,
#8,200,497, #7,970,606, #6,912,495 B2.
w
e
yt
q
r
SUPPLIED ACCESSORIES
1DC power cable ..........................................1
2Control cable...............................................1
3Angles.........................................................2
4Screws (M4×8 mm).....................................4
5Set screws (M3×6 mm) ...............................4
6Tapping screws (M3×8 mm) .......................2
1 mm ≈1/32 inch
OPENING CASE
1. Remove 7 screws from top and 2 screws
each from both sides of the repeater, then
slide off the top cover to the direction of the
arrow as illustration below.
P
0
P
1
P
2
P
3
P
4
2. Remove 3 screws from bottom and 2 screws
each from both sides of the repeater.
P
0
P
1
P
2
P
3
P
4
3. Disconnect the control cable from the channel
module (original), then remove the front
panel.
P
0
P
1
P
2
P
3
P
4
Channel module
(original)
Front panel
4. Remove 6 screws from the front panel, then
remove the shielding plate and rubber seal.
Rubber seal
Shielding plate
Icom is not responsible for the destruction,
damage to, or performance of any Icom or
non-Icom equipment, if the malfunction is
because of:
• Force majeure, including, but not limited to,
res, earthquakes, storms, oods, lightning,
other natural disasters, disturbances, riots,
war, or radioactive contamination.
• The use of Icom transceivers with any
equipment that is not manufactured or
approved by Icom.
Icom, Icom Inc. and the Icom logo are registered
trademarks of Icom Incorporated (Japan) in
Japan, the United States, the United Kingdom,
Germany, France, Spain, Russia, Australia, New
Zealand, and/or other countries.
All other products or brands are registered
trademarks or trademarks of their respective
holders.
INSTRUCTIONS
Thank you for choosing this Icom product.
READ ALL INSTRUCTIONS carefully and
completely before using this product.
1-1-32 Kamiminami, Hirano-ku,
Osaka 547-0003, Japan
A6657W-1EU-4
Printed in Japan
© 2008–2020 Icom Inc.
CHANNEL EXTENSION MODULES
UR-FR5000
UR-FR5100
UR-FR6000
UR-FR6100
Jul. 2020
INSTRUCTIONS

INSTALLATION
• Install the Channel Extension Module
1. Attach the supplied angles to both sides of the channel
extension module, and tighten the 2 supplied screws (M4×8
mm) on each side.
2. Install the channel extension module using the supplied screws
(Tapping screws: M3×8 mm, Set screws: M3×6 mm) as shown
below.
Set screws
Tapping
screws
Channel module
(original)
Channel extention
module
• Connect the control cable
1. Connect the supplied control cable to J502 on the front board as
shown below.
2. Cut the rubber caps of the control cables, then insert the rubber
caps to the front panel’s chassis as shown below.
J502
q w
ASSEMBLING THE UNIT
1. Replace the rubber seal and shielding plate of the front panel,
then tighten the 6 screws.
• Make sure the rubber seal is properly seated in the groove of
the chassis.
• Be sure to match the correct positions of the holes of the
shielding plate and projections of the front panel’s chassis.
Rubber seal
Holes
Projections
2. Connect the control cables to the channel modules.
P
0
P
1
P
2
P
3
P
4
Shorter cable
(lower side)
Longer cable
(upper side)
Channel module
(original)
Channel extention module
3. Return the front panel, top cover and screws to their original
positions.
P
0
P
1
P
2
P
3
P
4
P
0
P
1
P
2
P
3
P
4