ICP DAS USA M-7011D User manual

M-7011D 1-channel Thermocouple input DAQ Module - QuickStart (Oct/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
1
M-7011D
1-channel Thermocouple Input Data
Acquisition Module
Quick Start Guide
Product Website:
https://www.icpdas-usa.com/m_7011.html
http://www.icpdas-usa.com/dcon_utility_pro.html
1. Introduction
The M-7011 is a one-channel Thermocouple input module. It provides cost-
effective protection and conditioning for a wide range of valuable industrial
control signals and systems. We provide free DCON utility which can help
users configure and test M-7011 modules. Plenty of library functions and
demo programs are provided which allows users to develop programs
easily on Windows, Linux and DOS operating systems. Users can mount
the modules on a DIN rail, panel or wall. Modules have a screw-terminal
block to connect to the signals.
2. Terminal Assignment

M-7011D 1-channel Thermocouple input DAQ Module - QuickStart (Oct/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
2
3. Block/ Wiring Diagram

M-7011D 1-channel Thermocouple input DAQ Module - QuickStart (Oct/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
3
4. Default Settings
Default setting for M-7011/11D :
- Address : 01
- Analog Input Type : Type 05, -2.5 to +2.5 V
- Baudrate : 9600 bps
- Checksum disable, 60Hz rejection, engineer unit format
5. Configuration
To install the module, follow the steps below:
1. Connect the thermistor analog input.
2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If
the host is only equipped with an RS-232 interface, then an RS-232 to RS-485
converter will be required.
3. Connect the module to the power supply using the +Vs and GND terminals. Note that
the voltage supplied should be in the range of +10 to +30V DC.
4. Open DCON utility pro
click on COM port(first icon).
It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to
search module. The default settings for the module can be found in Section 3. Click OK
after selecting the COM port setting.

M-7011D 1-channel Thermocouple input DAQ Module - QuickStart (Oct/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
4
5. DCON utility pro will search for the selected COM port according the setting
previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS
and the others modules.
6. Configuration I/O module setting on PC

M-7011D 1-channel Thermocouple input DAQ Module - QuickStart (Oct/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
5
7. For M-7000 modules, DCON utility pro terminal can send command to the module.
See user manual Sections 2 for details command.
Configure the module: sending the %AANNTTCCFF command. See Section 2.1 for
details. To configure the M-7005, the $AA7CiRrr command must also be sent. See user
manual Section 2.12 for details. For M-7000 modules using the Modbus RTU protocol,
configure the module using the following functions.
-Sub-function 04h of Function 46h, see user manual Section 3.6.2
-Sub-function 06h of Function 46h, see user manual Section 3.6.4
-Sub-function 08h of Function 46h, see user manual Section 3.6.6
Read data from the input channels: send either the #AA or #AAN commands to the
module. See user manual Sections 2.3 and 2.4 for details. For M-7000 modules using
the Modbus RTU protocol, use Function 04h to read the data from the input channels.
See user manual Section 3.3 for details.

M-7011D 1-channel Thermocouple input DAQ Module - QuickStart (Oct/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
6
8. If user doesn’t know command, user can select Address and ID, it will show some
refer commands as below. User can select necessary command to test or debug
modules.