ICP DAS USA M-7018-16 User manual

M-7018-16 16 Channel Analog Input & Thermocouple Module- QuickStart (Oct/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
1
M-7018-16
16 Channel Analog Input & Thermocouple
Input Data Acquisition Module
Quick Start Guide
Product Website:
https://www.icpdas-usa.com/m_7018_16
https://www.icpdas-usa.com/dcon_utility_pro.html
1. Introduction
The M-7018-16 is an analog input module designed with 16 differential analog input
channels. The voltage input ranges from ±15 mV to ±2.5 V, the current input range can
be either +4 to +20 mA, 0 to +20 mA, or ±20 mA, and types J, K, T, E, R, S, B, N, C, L,
M, LDIN43710 thermocouple can be used for the thermocouple input. Designed with
overvoltage protection of up to 30 VDC is provided. M-7018-16 features per-channel
open wire detection for the thermocouple input types, 4 kV ESD protection and 3000
VDC intra-module isolation.
2. Terminal Assignment

M-7018-16 16 Channel Analog Input & Thermocouple Module- QuickStart (Oct/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
2
3. Block/ Wiring Diagram
4. Default Settings
Default settings for the M-7017, M-7018 and M-7019 series modules are:
▫Protocol: Modbus RTU
▫Module address: 01
▫Analog input type:
Type 08, -10V to 10V, for the M-7017 and M-7019 series
Type 1B, -150V to 150V, for the M-7017R-A5
Type 0D, -20mA to +20mA for the M-7017C and M-7017RC
Type 05, -2.5V to 2.5V, for the M-7018 series
▫Baud Rate: 9600 bps
▫Filter set at 60Hz rejection (Not used by the M-7019R, firmware version B2.6 and
earlier)

M-7018-16 16 Channel Analog Input & Thermocouple Module- QuickStart (Oct/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
3
5. Configuration
To install the module, follow the steps below:
1. Connect the thermistor analog input.
2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If
the host is only equipped with an RS-232 interface, then an RS-232 to RS-485
converter will be required.
3. Connect the module to the power supply using the +Vs and GND terminals. Note that
the voltage supplied should be in the range of +10 to +30V DC.

M-7018-16 16 Channel Analog Input & Thermocouple Module- QuickStart (Oct/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
4
4. Open DCON utility pro
click on COM port(first icon).
It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to
search module. The default settings for the module can be found in Section 3. Click OK
after selecting the COM port setting.

M-7018-16 16 Channel Analog Input & Thermocouple Module- QuickStart (Oct/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
5
5. DCON utility pro will search for the selected COM port according the setting
previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS
and the others modules.
6. Configuration I/O module setting on PC

M-7018-16 16 Channel Analog Input & Thermocouple Module- QuickStart (Oct/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
6
7. For M-7000 modules using the Modbus RTU protocol, configure the module using the
following functions.
Sub-function 04h of Function 46h, see user manual Section 3.3.2
Sub-function 06h of Function 46h, see user manual Section 3.3.4
Sub-function 08h of Function 46h, see user manual Section 3.3.6
For M-7000 modules using the Modbus RTU protocol, use Function 04h to read the
data from the input channels. See user manual Section 3.2 for details.

M-7018-16 16 Channel Analog Input & Thermocouple Module- QuickStart (Oct/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
7
8. If user doesn’t know command, user can select Address and ID, it will show some
refer commands as below. User can select necessary command to test or debug
modules.