ICP DAS USA PCI-P16POR16U User manual

PCI-P16POR16U, PEX-P8POR8i/P16POR16i Series Quick Start Guide ICP DAS CO., LTD.
1
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
The package includes the following items:
One PEX-PxPORxi/PCI-PxPORxU Series Card, as follows:
PEX-P8POR8i
PCI-P16POR16U
PEX-P16POR16i
One Software Utility CD (V6.2 or later)
One Quick Start Guide (This Document)
-
One CA-4037B Cable
One CA-4002 D-Sub connector
Two CA-4002 D-Sub connectors
For PCI-P16POR16U
PEX-P8POR8i/P16POR16i
Check the Supplied Items
English/Jun. 2015/Version 1.1

PCI-P16POR16U, PEX-P8POR8i/P16POR16i Series Quick Start Guide ICP DAS CO., LTD.
2
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
Step 1: Setup the Windows driver. The driver is located at:
The UniDAQ driver supports 32-/64-bit Windows 2K/XP/2003/Vista/7/8; it is
recommended to install this driver for new user:
CD: \NAPDOS\PCI\UniDAQ\DLL\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/
The PISO-DIO Series classic driver supports Windows 98/NT/2K and 32-bit
XP/2003/ Vista/7/8. Recommended to install this driver for have been used
PISO-DIO series boards of regular user, please refer to :
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/piso-dio/manual/quic
kstart/classic/
Step 2: Click the “Next>” button to start the installation.
Step 3: Check your DAQ Card is or not on supported list, then click the “Next>” button.
Step 4: Select the installed folder, the default path is C:\ICPDAS\UniDAQ, confirm and
click the “Next>” button.
Step 5: Check your DAQ Card on list, then click the “Next>” button.
Step 6: Click the “Next>” button on the Select Additional Tasks window.
Step 7: Click the “Next>” button on the Download Information window.
Step 8: Select “No, I will restart my computer later” and then click the “Finish” button.
For detailed information about the driver installation, please refer to Chapter 2.1
“Getting the UniDAQ Driver DLL Installer package” of the UniDAQ SDK user manual.
Installing the Windows Driver

PCI-P16POR16U, PEX-P8POR8i/P16POR16i Series Quick Start Guide ICP DAS CO., LTD.
3
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
1. CON1/CN1:
The connector for DI/O channels 0-7. Refer to Section 5 Pin
Assignments.
2. CON2:
The connector DI/O channel 8-15. Refer to Section 5 Pin
Assignments.
3. SW1:
Card ID function. Refer to PCI-P16R16 Series User Manual.
4. J1/JP1-JP8:
Input AC or DC signals for DI 0-7. Refer to the table below.
5. J2/JP9-JP16:
Input AC or DC signals for DI 8-15. Refer to the table below.
6. JP2/J2:
Ground Isolated Protection Jumper. Refer to PCI-P16R16 Series User
Manual.
7. J1:
Ground Isolated Protection Jumper for PCI-P16POR16U. Refer to
PCI-P16R16 Series User Manual.
Please make sure input signal type jumper (J1, J2, JP1-JP8 and JP9-JP16) is kept in default
setting before self-test, as follows:
Jumper
Without Filter for DC
Signal
(Default Settings)
Without AC Filter for AC
Signal
PEX-P8POR8i
PEX-P16POR16i
J1
J2
PCI-P16POR16U
JP1 –JP8
JP9 –JP16
Jumper Setting
3
1
2
3
1
2








PCI-P16POR16U, PEX-P8POR8i/P16POR16i Series Quick Start Guide ICP DAS CO., LTD.
4
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
Step 1: Shut down and power off the computer.
Step 2: Remove all the covers from the computer.
Step 3: Select an unused PCI Express/PCI slot.
Step 4: Carefully insert your card into the PCI
Express/PCI slot and secure the board in
place.
Step 5: Replace the covers on the computer.
Step 6: Reconnect the power supply and power on
the computer.
Step 7: Once the computer reboots, follow any messages that may be displayed to
complete the Plug and Play installation procedure.
Step 8: Open the “Device Manager” in the Control Panel and verify that the
PCI-PxPORxU/PEX-PxPORxi series card is listed correctly, as illustrated below.
Installing the Hardware
Installation Successful

PCI-P16POR16U, PEX-P8POR8i/P16POR16i Series Quick Start Guide ICP DAS CO., LTD.
5
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
Pin Assignments
Extension Cable (CA-4037B):
DB-40-Pin conversion DB-37-Pin

PCI-P16POR16U, PEX-P8POR8i/P16POR16i Series Quick Start Guide ICP DAS CO., LTD.
6
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
Prepare for device:
One CA-3710 Cable (optional).
DN-37 (optional) wiring terminal board.
Exterior power supply device. For example: DP-665 (optional)
Self-test wiring as follows:
Step 1: Connect the DN-37 to the CON1/CN1 connector on board using the CA-3710
cable.
Step 2: Connect the NO(0-7) pins to the DIA(0-7) pins.
(i.e., connect the Pin1/2/3/4/5/6/7/8 to Pin12/13/14/15/16/17/18/19)
Step 3: Connect the External Power Supply GND to the CM0…CM7 pins.
Connect the External Power Supply GND to the GND pin.
(i.e., connect the Power Supply GND to Pin20/21/22/23/24/25/26/27/29)
Step 4: Connect the External Power Supply (+24 V) to the DIB0…DIB7 pins.
(i.e., connect the Power Supply +24V to Pin30/31/32/33/34/35/36/37)
Self-Test
DN-37 I/O Wiring
GND
GND
+5V
1 3 4 56 7 8910 11 13 14 17 15 16 18
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
12
2
+24V
37
19
External:
DP-665
3
4
2
1
CON1
Cable: CA-3710

PCI-P16POR16U, PEX-P8POR8i/P16POR16i Series Quick Start Guide ICP DAS CO., LTD.
7
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
Step 5: Execute the UniDAQ Utility Program.
1. In Windows 7, click the “Start” button,
point to “All Programs”,and then click the
“ICPDAS”folder. Point to “UniDAQ
Development Kits”and then click the
“UniDAQ Utility”to execute the UniDAQ
Utility Program.
2. Confirm that PCI-P16R16 Series card has
been successfully installed in the Host
system. Note that the device numbers
start from 0.
3. Click the “TEST”button to start the test.
Step 6: Check the results of the DIO function test.
1. Click the “Digital Output”tab.
2. Select “Port0”from the “Port Number”drop-down menu.
3. Check the checkboxes for channels 0, 2, 4 and 6.




PCI-P16POR16U, PEX-P8POR8i/P16POR16i Series Quick Start Guide ICP DAS CO., LTD.
8
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
4. Click the “Digital Input”tab.
5. Select “Port0”from the “Port Number”drop-down menu.
6. The DI indicators will turn red when the corresponding DO channels 0, 2, 4
and 6 are ON.
PEX-P8POR8i/P16POR16i and PCI- P16POR16U Series Card Product Page:
http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/pci-p16por16.ht
ml
DN-37, CA-3710 and DP-665 page (optional):
http://www.icpdas.com/products/DAQ/screw_terminal/dn_37.htm
http://www.icpdas.com/products/Accessories/power_supply/dp-665.htm
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
Documentation and Software:
CD:\NAPDOS\PCI\UniDAQ\
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/
Related Information


