ICP DAS USA WLS-T01 User manual

Version 1.0.0
Page 1
Copyright © 2016 by ICP DAS Co., Ltd. All ights eserved.
WLS-T01
Quick Start
1 What’s in the Shipping Package?
The shipping package contains the following items:
If any of these items are missing or damaged, please contact your local
distributor for more information. Save the shipping materials and cartons in
case you need to ship the module in the future.
Quick Start
WLS-T01
module
CR-123A 3.0v
Lithium battery
4SI11G0000009)

Version 1.0.0
Page 2
Copyright © 2016 by ICP DAS Co., Ltd. All ights eserved.
2 Preparing the Device
1. Use the Phillips screwdriver to loosen the back cover screws, open the
case and place the CR123A 3.0v battery as shown in Fi ure 1。
(CAUTION: Do not reverse the installation of the battery, and the
battery is a disposable non-rechar eable lithium battery, do not use
the char er to char e)
Fi 1. Battery installation
2. Pressin the up (▲) or down (▼) button to wake up the WLS-T01, as
shown in Fi ure 2, and confirm that the reen LED is blink。If the
reen LED is blink, it means the module is runnin ; if the reen LED is
not blink, it means the module is not runnin .
Fi 2. Pressin the button
Loosen the back cover screws
+
-
overturned
LED
Up
Down

Version 1.0.0
Page 3
Copyright © 2016 by ICP DAS Co., Ltd. All ights eserved.
3 Mode, Button function and LED description
WLS-T01 has two built-in modes, "Runnin mode" and "Settin
mode". The functions of these two modes are described as follows:
1. Runnin mode: This mode is used to transmit location packa e
every 3 seconds in the back round. In this mode, the user can
press the button to send an alarm packa e or enter the settin
mode. When the pre-job(section 2) is completed, WLS-T01 will
default to the "Runnin Mode".
2. Settin mode: This mode is used to transmit Node ID forcefully,
and set the RF Power and RF Channel by Button. If the user
does not press any button for 8 seconds, the module will
automatically save and directly enable the settin value, and
then leave the "Settin Mode" to the "Runnin Mode".
In the above two modes, pressin different buttons will correspond
to different functions, and various functions will be indicated by the
different blinkin frequency of LED. Please refer to Fi .3, Table 1 and
Table 2:
Fi 3. Product appearance
Help
Green
LED
Red
LED
Up
Down
Help

Version 1.0.0
Page 4
Copyright © 2016 by ICP DAS Co., Ltd. All ights eserved.
Table 1. Runnin mode description
Runnin mode (default)
Item Button LED status Description
1 ● Green LED blink once, and
then red LED steady lit 1
second after 0.6 second.
Pressin the button
for 0.6 second will
transmit Help
packa e.
2 ▲+▼ Green LED blink every 0.5
second, and it chan e to red
LED blink after 3 second.
The settin mode is entered.
Pressin the two
buttons to ether for
3 second will enter
settin mode.
3 No
pressin
Red LED blink every 3
second.
Battery is low power.

Version 1.0.0
Page 5
Copyright © 2016 by ICP DAS Co., Ltd. All ights eserved.
Table 2. Settin mode description
Settin mode
Item Button LED status Description
1 ●：chan e to
item 2
▲：none
▼：none
Red LED blink every 0.2
second.
Automatically
transmit Node
ID of module.
2 ●：chan e to
item 3
▲：+1
▼：-1
ARed LED blink every
0.5 second.
BWhen +1 or -1, reen
LED blink. If the value
is equal to maximum
value or minimum
value , the reen LED
will continuous blink.
Settin wireless
RF power, the
minimum value
to maximum
value is 0 to F,
16 se ments.
The default
value is F.

Version 1.0.0
Page 6
Copyright © 2016 by ICP DAS Co., Ltd. All ights eserved.
3 ●：chan e to
item 1
▲：+1
▼：-1
ARed LED blink every 1
second.
BWhen +1 or -1, reen
LED blink. If the value
is equal to maximum
value or minimum
value , the reen LED
will continuous blink.
Settin wireless
RF channel, the
minimum value
to maximum
value is 0 to F,
16 se ments.
The default
value is 4.

Version 1.0.0
Page 7
Copyright © 2016 by ICP DAS Co., Ltd. All ights eserved.
4 Startup to use
Wireless Location System (WLS) includes the modules that RFU-400,
WLS-T01, WLS-R01 and WLS software, as show in fi ure 4. The user
need to check the wireless settin of each module as below. If the user
need more detail about parameters of wireless settin , please refer to the
user manual of each module.
Fi 4. Wireless Location System Architecture
1. RFU-400：
1
2
3
4
5
6
7
8
ON
RF Channel RF Rate
Group ID Baud Rate
Data Format
LSB
MSB
RS-232
RS485
RFU
-
400
WLS software
WLS
-
R0
WLS
-
R0
WLS
-
R0
WLS
-
T01
2.4GHz
Sub 1GHz

Version 1.0.0
Page 8
Copyright © 2016 by ICP DAS Co., Ltd. All ights eserved.
2. WLS-T01：
It is not required to adjust the wireless settin of WLS-T01. The
default value about RF channel is 4, RF power is F, Node ID is the last two
bytes of build-in IEEE address. If the user adjust WLS-R01 2.4GHz RF
channel to 4, the WLS-R01 will can receive the wireless packa e.
3. WLS-R01：
5 Remarks
1. If you encounter any difficulties, please send the problem description
to the [e-mail] mailbox, there will be someone to serve
you.
2. If the user needs to replace the lithium battery, you can purchase in
electronic business, or refer to accessories in the product pa e.
1 2 3 4 5 6 7 8 9 10 11 12
ON
400M
RF Channel
2.4G
RF Channel
400M
Node ID
400M
Group ID
Filter
LSB MSB