ICRealtime F Series User manual

F Series Indoor IP Camera User’s Manual
For F725/F726/F715/F665/F645/F625 series only

Welcome
Thank you for purchasing our IP camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Installation
Do not apply power to the IP camera before completing installation.
Do not put object on the IP module.
3．Environment
This series IP camera should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
Please open the accessory bag to check the items one by one in accordance with the list below.
Contact your local retailer ASAP if something is missing or damaged in the bag.
Accessory Name F726/ F725/ F715 Series F625/F645/F665 Series Amount
IPC Unit ■■1
Lens □■1
Power Adapter ■■1
Quick Start
Guide ■■1
Warranty Card ■■1
Certificate Card ■■1
CD ■■1

Table of Contents
1General Introduction ..................................................................................................................6
1.1 Overview........................................................................................................................6
1.2 Feature...........................................................................................................................6
1.3 Specification..................................................................................................................7
1.3.1 Performance...........................................................................................................7
1.3.2 Function Specification ..........................................................................................8
1.3.3 Factory Default Setup.........................................................................................11
2Framework.................................................................................................................................15
2.1 Rear Panel...................................................................................................................15
2.2 Side Panel ...................................................................................................................19
2.3 Lens..............................................................................................................................19
2.4 Remote Control...........................................................................................................20
2.5 Bidirectional talk .........................................................................................................21
2.5.1 Device-end to PC-end ........................................................................................21
2.5.2 PC-end to the device-end ..................................................................................22
3Installation .................................................................................................................................23
3.1 Lens Installation..........................................................................................................23
3.1.1 Auto Aperture Lens .............................................................................................23
3.1.2 Manual Lens.........................................................................................................23
3.1.3 Remove Lens.......................................................................................................24
3.1.4 SD Card Installation ............................................................................................24
3.1.5 Remove SD card .................................................................................................25
3.1.6 3G Card Installation ............................................................................................26
3.1.7 Remove 3G card .................................................................................................27
3.1.8 I/O Port..................................................................................................................27
4System Network .......................................................................................................................29
4.1 General Network.........................................................................................................29
4.2 3G Network .................................................................................................................29

5Quick Configuration Tool.........................................................................................................30
5.1 Overview......................................................................................................................30
5.2 Operation .....................................................................................................................30
6Web Operation..........................................................................................................................33
6.1 Network Connection...................................................................................................33
6.2 Login and Main Interface...........................................................................................33
7GUI Operation...........................................................................................................................36
7.1 Main Menu...................................................................................................................36
7.2 Network Setup ............................................................................................................36
7.3 Encode Setup .............................................................................................................37
8Wireless Network Access Setup (For W Series Only) .......................................................39
8.1 Wireless Router Setup...............................................................................................39
8.2 IPC Web Network Setup ...........................................................................................40
8.3 Web Setup...................................................................................................................41
9FAQ ............................................................................................................................................42

6
1General Introduction
1.1 Overview
This series IP camera integrates the traditional camera and network video technology. It adopts
audio video data collection, transmission (wire, WIFI, 3G), storage together. It can connect to the
network directly without any auxiliary device.
This series IPC uses standard H.264 video compression technology and AMR, G.711a/u audio
compression technology, which maximally guarantee the audio and video quality.
This series IPC has mega pixel resolution and supports PoE and 12V DC power. It supports the
wireless network application, bidirectional talk, digital water mark and etc.
It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Due to its multiple functions and various uses, this
series IPC is widely used in many environments such office, bank, road monitor and etc.
1.2 Feature
User
Management
zDifferent user rights for each group, one user belongs to one group.
Data
Transmission
zBuilt-in USB port supports TD-SCDMA、EVDO（CDMA2000 1X）、
WCDMA module so that IPC can support mobile communication data
transmission.
zBuilt-in USB port support Wifi module so that the IPC can support the
wireless data transmission.
zSupport cable network data transmission via Ethernet
Storage
Function
zSupport central server backup function in accordance with your
configuration and setup in alarm or schedule setting
zSupport record via Web and the recorded file are storage in the client-
end PC.
zSupport local SD card hot swap. Please note SD card can only
memorize the image.
Alarm
Function
zReal-time respond to external alarm input( within 200MS) as user pre-
defined activation setup and exert corresponding message in screen
and audio prompt(allow user to pre-record audio file)
zProvide central management server management option so that system
can automatically send alarm notice remotely. Alarm input can connect
to various peripheral equipments.
zProvide prompt or alarm option when encounter video loss.
zSupport SMS(short messaging service) function when alarm occurs.
Network
Monitor
zIPC supports one-channel audio/video data transmit to network terminal
and then decode. Delay is within 500ms (network bandwidth support
needed)
zMax supports 10 connections.
zAdopt the following audio and video transmission protocol: HTTP, TCP,
UDP, MULTICAST and RTP/RTCP and etc.
zSend some alarm data or message via SMTP.
zSupport web access, widely used in WAN.
Network
Management
zRealize IPC configuration and management via Ethernet.
zSupport device management via web.

7
Peripheral
Equipment
zSupport peripheral equipment management, each peripheral equipment
control protocol and interface can be set freely.
zSupport serial port (RS232/RS485) transparent data transmission.
Power zExternal power adapter
zPoE
Assistant
Function
zDay/Night mode auto switch
zAuto aperture setup (For 715/F6X5 series only).
zBacklight compensation: screen auto split to realize backlight
compensation to adjust the bright.
zSupport video watermark function to avoid vicious video modification.
zVideo format support NTSC and PAL.
zSupport system resource information and running status real-time
display. Support log function.
zUse IR receiver to receive the IR signal. (For F726/715/F6X5 series
only).
zElectronic PTZ: electronic zoom, direction move (For F725 series only)
1.3 Specification
1.3.1 Performance
Please refer to the following sheet for IPC performance specification.
Specification
Name IPC-F726 IPC-F725 IPC-F715 IPC-F6X5
Standard
PAL：1f/s～12.5f/s.
NTSC：1f/s～15f/s (Now
it max supports 12.5f/s. )
PAL：1f/s～25f/s. NTSC：1f/s～30f/s
Encode
capacity One 720＋one HD1 One 720＋one HD1 One 720＋one HD1 One D1+ one CIF
Video
Encode Bit
Stream
Main stream：
UXGA (1600*1200)
Extra stream：
D1(704*576/704*480)
HD1(352*576/352*480)
CIF
（352*288/352*240）
QCIF(176*144/176*128)
QVGA(320*240)
QQVGA(160*128）
UXGA (1600*1200)
WSXGA(1600*1024)
SXGA (1280*1024)
WXGA(1280*800）
XVGA(1024*768）
SVGA(800*600）
VGA(640*480）
QVGA(320*240）
D1(704*576/704*480)
HD1(352*576/352*480)
CIF(352*288/352*240)
QCIF(176*144/176*128)
QVGA(320*240）
QQVGA(160*128)
720(1280*720）
1.3M（1280*960）
720（1280*720）
VGA（640*480）
QVGA（320*240）
D1
（704*576/704*480）
HD1
（352*576/352*480）
CIF
（352*288/352*240）
QCIF
（176*144/176*128）
QQVGA（160*128）
D1
（704*576/704*480）
BCIF（720*288）
HD1
（352*576/352*480）
CIF
（352*288/352*240）
QVGA（320*240）
QCIF
（176*144/176*128）
QQVGA（160*128）

8
Video
Record
Speed
PAL：1f/s～12.5f/s.
NTSC：1f/s～15f/s
(Now it max supports
12.5f/s. )
UXGA/WSXGA/SXGA/
WXGA/XVGA:
1f/s to 15f/s per
channel(adjustable)
Other resolutions:
PAL：1f/s-25f/s per
channel (adjustable).
NTSC：1f/s-30f/s per
channel (adjustable).
1.3M resolution:
PAL：1f/s-12f/s per
channel (adjustable).
NTSC：1f/s-22f/s
per channel
(adjustable).
Other resolutions:
PAL：1f/s-25f/s per
channel (adjustable).
NTSC：1f/s-30f/s
per channel
(adjustable).
PAL：1f/s-25f/s per
channel (adjustable).
NTSC：1f/s-30f/s per
channel (adjustable).
Network Capacity
Max support 10 network users to monitor simultaneously
TCP output capacity 75Mbps
UDP output capacity 85Mbps
Power Consumption
Usually it is 4W and
the max value is less
than 5W.
Usually it is 3W and the max value is less than 4W.
DC 12V
Power PoE（48V DC）
Working environment temperature：-10℃～50℃
Temperature Chassis internal rising temperature is less than 20℃（When IPC is working ,the chassis internal
temperature deducts environment original temperature.）
Working
Environment
Humidify
10%～90％
Dimension(H*W*D）58mm*69mm*139mm
Weight 500g
1.3.2 Function Specification
Please refer to the following sheet for function specification information.
Note
Specification F725 F715 F6X5 F726
Zoom Adjustment Manual
Focus Adjustment Manual
Lens Control
Aperture Adjustment Manual DC Manual/Auto
DC
Manual/Auto
DC N/A
Backlight compensation
control Manual On/Off
White balance
adjustment Auto
Contrast ness adjustment Manual/Auto
Bright ness adjustment Manual/Auto
Electronic shutter control Auto Manual/Auto Manual/Auto Auto
CCD Video
Process
Color/B&W(Day/Night)
switch
Manual/Auto
Note
The color/B&W (Day/Night) switch here just an electronic switch.
System removes the color elements and reserves the B&W
elements. It is not a filter switch.
Video Resolution UXGA、WSXGA、
SXGA、WXGA、
XVGA、SVGA、
1.3M、720、
VGA、
QVGA、D1、
D1、BCIF、
HD1、CIF、
QVGA、
UXGA、
D1、
HD1、CIF、

9
VGA、QVGA、
D1、HD1、CIF、
QCIF、
QVGA、QQVGA、
720
HD1、CIF、
QCIF、
QQVGA
QCIF、
QQVGA
QCIF、
QVGA、
QQVGA
Video compression Standard H.264 encode/decode format
MPEG4
video
compression
standard
Motion Detection Take 18*22 pix as a macro unit. Support 396 detection zones.
Sensitivity level ranges from 1 to 6.
Dual-stream 1-ch 15f UXGA＋1-
ch CIF
1-ch 25f 720＋
1-ch HD1
1-ch 25f D1
＋1-ch 25f
CIF
1-ch 12.5f
UXGA＋1-
ch
12.5f CIF
Bidirectional Talk Delay within 200ms
Audio Audio Listening 1-ch MIC input.
WEB access via IE browser.
PPPoE dial function
DHCP auto get IP address
DDNS
SMTP email function
NTP time synchronization.
DNS domain parse
IP address filter
IP address auto search function
Network
Wireless Network Interface :802.11b/g N/A
Schedule Record Support max 6 periods.
Manual Record After enabling manual record, no matter system is in schedule or
alarm status or not, system just begins recording.
Alarm Record System automatically enables recording function when alarm
occurred.
Record
Motion Detection Record When video changes, system automatically enables record
operation.
Time Title Display
There are 255 layers.
O is the bottom layer and 255 is the highest layer.
O means completely transparent and 255 is opaque.
Channel Title Display Please refer to the above information.
OSD
Privacy Mask Max supports 8 zones.
Local SD storage Support high-speed card/low-speed card
Based on SDK network
storage
Storage
Based on FTP network
storage
Supported
Network alarm/local
alarm output 1-ch local/network alarm output
Alarm Local alarm/network
alarm input 1-ch local/network alarm input
Event
Management
Activate alarm via motion
detection or external
input
Please enable pre-record function when activating the alarm

10
Upload video file or
JPEG file via email、
FTP、HTTP
Upload automatically
Send out alarm notice via
email, HTTP and external
port.
Support de-jitter when alarm occurs frequently.
Support video short time
buffer storage before or
after alarm
Pre-record is 2Mbytes. Buffer storage video of 5s.
RS485 PTZ control Support semi-duplex communication way.
Control
RS232 For debug
Network remote upgrade Use upgrade tool.
On-line
Upgrade COM upgrade Upgrade from network via COM command.
COM control platform
View IPC running status or IPC parameter via COM port.
Device
Management Network client-end
Log in the client-end software in the PC to monitor IPC.
IPC provides device information, video information, COM setup, record setup, motion detection
setup, alarm setup, OSD information interfaces to modify system setup.
Parameter
Configuration IPC provides running information such as user port, log, status, user management, email setup,
date modification.
Log
System can record the important event log record
Record the following information：
System operation, setup operation, alarm event, record management, user management, clear
log.
Water Mark To avoid vicious video modification.
PoE (For –P series only). Comply to IEEE802.3af standard
Power
supply DC12V power supply
RESET Support hardware/software/Watchdog reset. Watch dog max supports 35 seconds.
Alarm input port
Analog audio input/output port. Analog video output port
Network port
Port ESD
protection
12V power adapter
One analog video output port
One audio input port
One audio output port
Two alarm input
ports One alarm input port One alarm input
port
Two alarm input
ports
One alarm output port
One network interface（RJ45 10M/100M self-adaptive Ethernet port）
One wireless network interface（For –W series only）Reserved
Interface
One remote control receiver port

11
One SD card port
Support high-speed card/low-speed card.
One 3G card port (For 3G series only.) Reserved
One red/green running status indication light.
One green network receive and send indication light （Network interface seat has ）
One yellow network connection indication light （Network interface seat has）
One green wireless network receive/send indication light. (For –W
series only.) Reserved
One RESET button
Others
Auto aperture port. (DC drive mode）Reserved
Installation Bracket installation
1.3.3 Factory Default Setup
Please refer to the following sheet for factory default setup information.
Default setupFunction Configuration
Type Item Name F726 F725 F715 F6X5
Date format Y-M-D
DST Disable by default
Date separator ‘ _ ’
Time format 24H
Language Simplified Chinese
When HDD is full Overwrite
Record duration 60M
Device No. 8
General Setup
Video type PAL
Channel Channel01
Encode mode MPEG4 H.264 H.264 H.264
Audio/Video enable Enable audio and video
General bit stream General bit stream
Resolution UXGA 720 720 D1
Frame rate 25
Bit stream control VBR
Quality Good
Bit stream value 4096 2048 2048 2048
Main
Stream
I frame interval control 24 50 50 50
Extension Stream General bit stream
Audio/Video enable Enable audio and video
Resolution CIF
Frame rate 12 25 25 25
Bit stream control VBR
Quality Good
Bit stream value 512
Extra
Stream
I frame interval control 50
Image Color Brightness:50
Contrast:50
Sautratioon:50
Hue:50
Encode
Setup
Watermark Enable

12
Watermark: all
Watermark type: character
Watermark: DigitalCCTV
Privacy Mask Never
Time title Enable. OSD transparent :128
Channel title Enable. OSD transparent :128
Channel Ch01
Pre-record 5 seconds.
Start Time 0:00:00
End Time 23:59:59
Record Period 1:Enable motion
detection/alarm
Snapshot Period 1: Enable motion
detection/alarm
Record Setup
Time Setup
Week Sunday
Option COM01
Function General
Data bit 8
Stop bit 1
Baud rate 115200
COM Setup
Parity None
Ethernet Port 01
DHCP Disable
IP address 192.168.1.108
Subnet mask 255.255.0.0
Gateway 192.168.0.1
Device name Device factory default name
TCP port 37777
HTTP port 80
UDP port 37776
Network user connection
amount
10
Network transmission QoS Disable
Remote host Multiple broadcast group
Enable Disable
IP address 239.255.42.42
Port 36666
Email setup Enable
Multiple DDNs Disable
NAS setup Disable
NTP setup Disable
Network Setup
Alarm server Disable
Event type Local input
Alarm input Input 01, disable
Type Normal open
Setup Period:
Start time 0:00:00
End time:23:59:59
Period 1:enable
Week: Sunday
Anti-dither 0 second
General output Disable
Alarm latch 10 seconds
Alarm Setup
Record channel 1, enable

13
Record latch 10 seconds
Send email Disable
PTZ activation Disable
Event type: never
Address: 0
Snapshoot Disable
Event type Motion detection
Channel Ch01, Disable
Sensitivity 3
Time period setup Period:
Start time 0:00:00
End time:23:59:59
Period 1:enable
Week: Sunday
Anti-dither 5 seconds
General output Disable
Alarm latch 10 seconds
Record channel Disable
Record latch 10 seconds
Send email Disable
PTZ activation Event type: Never
Address: 0
Disable
Video Detection
Snapshot Disable
Channel Ch01
Protocol EPTZ EPTZ DH-
SD1
DH-
SD1
Address 1
Baud rate 115200
Data bit 8
Stop bit 1
PTZ Setup
Parity None
All Disable
General Disable
Encode Disable
Record Disable
COM Disable
Network Disable
Alarm Disable
Video detection Disable
Display output Disable
Default and Backup
Channel No. Disable
Record control Auto. Ch1 (This series device does not
support this function.)
Even Type No HDD, Disable
General
Output
Disable
Alarm Latch 10 seconds
Abnormity
Send email Disable
User account admin--- password: admin (reusable)
888888--- password: 888888(reusable)
666666--- password: 666666(reusable)
default--- password: tluafed
Channel Ch01
Advanced
Snapshot
Snapshot Scheduled

14
mode
Frame rate 1f/s
Resolution D1
Quality 60%
Auto reboot 2.00 each dayAuto
maintain Auto delete
old files
Never
Channel 1
Exposure Mode Auto
Day/Night Mode Color
Backlight Compensation Disable
Auto Aperture N/A N/A Disable Disable
White Balance N/A
Signal Type Internal input
Mirror Disable Disable N/A N/A
Camera Property
Flip Disable Disable N/A N/A
Enable Disable
SN 1
IP 0.0.0.0
Port 7000
Auto Registration
Device ID Dahua
DNS 202.101.172.35 DNS Setup
Alternative DNS 202.101.172.35

15
2Framework
2.1 Rear Panel
This series IP camera real panel is shown as below. See Figure 2-1.
Figure 2-1
Please refer to the following sheet for detail information.
Interface Name Connector Function
VIDEO OUT Video output port BNC Output analog video
signal. Can connect to
TV monitor to view
video.
Wireless Antenna
Port
Connect to wireless
antenna to receive
WIFI/3G wireless
signal.
DC 12V Power port. Input 12V
DC
STATUS Status indication light It is to indicate camera
working status:
zThe red light
becomes on
when connect the

16
camera to the
power. The green
light flashes and
then becomes on,
which means
application is
running normally.
Now you can log
in via network.
zThe indication
light becomes off
when you reboot
the system via
software.
zThe green light
flashes when
system is
recording.
zThe red light
flashes when
system is
upgrading.
zThe red light is on
in safety mode.
WLAN Wireless network
indication light
The wireless network
indication light is to
display wireless
network working
status.
The network indication
light becomes green
when you connect the
IP camera to the
wireless network.
A RS485 port I/O port RS485_A port, control
external PTZ

17
B RS485_B port, control
external PTZ
1 Alarm input port 1 Alarm input port 1. To
receive the signal from
the external alarm
device.
2 Alarm input port 2 Alarm input port 2. To
receive the signal from
the external alarm
device. (For F725
series only.)
NO
C
1-ch alarm output Alarm output port. To
output alarm signal to
the alarm device.
NO: Normal open
alarm output end.
C: Alarm output public
end,
RX RS232_RX，RS232
receive end.
TX
Transparent debug
serial port
RS232_TX，RS232
COM send out end.
G GND Ground end
RESET RESET button Restore factory default
setup.
When system is
running normally
(power indication light
is green), press the
RESET button for at
least 5 seconds,
system can restore
factory default setup.

18
LEVEL Auto aperture
adjustment button
Adjust aperture level.
(For F715 and F6X5
series only)
Please always use
nonmetal material tool
to adjust.
IR Infrared remote
receiver
Receive the IR signal
from the remote
control.
(This function does
not apply to F725
series product.)
AUDIO OUT Audio output port Audio output 3.5mm
JACK port.
Output audio signal to
the device such as
sound box.
AUDIO IN Audio input port Audio input 3.5mm
JACK port.
Input audio signal.
Receive signals from
devices such as pick-
up.
LAN Ethernet port Connect to standard
Ethernet cable.
SD SD card port Connect to SD card.
Note
zWhen you install
the SD card,
please make sure
current card is not
in write mode and
then you can
install it to the
camera.
zWhen you
remove the SD
card, please

19
make sure current
card is not in write
mode. Otherwise
it may result in
data loss or card
damage.
zBefore hot swap,
please stop
record operation.
2.2 Side Panel
Please refer to the following interface for side panel dimension information. See Figure 2-2.
Figure 2-2
2.3 Lens
Please refer to the following interface for lens dimension information. See Figure 2-3.

20
Figure 2-3
2.4 Remote Control
Please refer to the following interface for remote control information. See Figure 2-4.
Figure 2-4
Please refer to the following sheet for detail information.
Icon Name Function
Reset device Reserved for future use
Emergency Reserved for future use