ICRealtime EL-2000 I-sniper User manual
I-Sniper Super Night Vision
Outdoor Camera
INSTRUCTION MANUAL
· EL-2000
Please read this manual carefully before installation and operation of the product.
120321-1
EL-2000 I-Sniper Super Night Vision Outdoor Camera
Copyright 2012, ICRealtime, Inc. Made in Korea.
Dear Customers!
INFORMATION
By selecting this product, you have decided to use a professional device that
guarantees highest quality and reliability. We would like to thank you very much for your
confidence and kindly ask you to read the following instructions carefully before
installation and operation in order to take full advantage of all quality features regarding
this product.
CAUTION
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
The lighting flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of non-insulated
dangerous voltage within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
This equipment has been tested and found to comply with limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at its own expense.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
CAUTION – To prevent electric shock and risk of the fire hazards
Do NOT use power source other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should conform to
all local codes.
2 3
Table of contents
1. Precautions ------------------------------------------------------------- 4
2. Limitation of liability --------------------------------------------------- 5
3. Disclaimer of warranty ----------------------------------------------- 5
4. Package ----------------------------------------------------------------- 6
5. Main Features --------------------------------------------------------- 7
6. Installation ---------------------------------------------------------- 8~9
6-1. Installation overview
6-2. 3-Axis Adjustment
6-3. Ext-Video
6-4. Waterproof processing of cable end connection
7. Tips for quick installation ---------------------------------------10
7-1. Quick control to Zoom & Focus
7-2. RS485 Connection
8. Functions and operation -------------------------------------- 11~14
8-1. OSD Menu Tree
8-2. Setting up the menu
1. WDR CONTROL
2. BLC
3. AGC
4. WHITE BALANCE
5. FLUORESCENT
6. ICR DVR TOOL
7. RS-485..
8. FLIP
9. SAVE&EXIT
10. DEFAULT
11. CANCEL
9. Troubleshooting ------------------------------------------------ 15~16
10. Dimension ---------------------------------------------------------- 16
11. Specification -------------------------------------------------------- 17
·Please read the manual carefully before the installation in order to set up the camera
correctly and to obtain the best picture quality.
· Please keep the manual in good condition for your future reference and service
application.
· Installation and services should be only carried out by an authorized personnel
according to local safety regulations.
· If any liquid or solid matter gets into the housing, immediately disconnect the camera
from power supply and have it checked by your authorized dealer before reusing.
· Avoid installing the camera at extremely hot or cold places.
· If you are not a certified person, never try to dismantle the camera. To avoid electric
shock, never remove the screws or covers. There are no parts inside that need
maintenance by the user. All maintenance should be carried out by qualified
personnel.
· Avoid installing the camera at a place of high humidity.
· Avoid installing the camera at the place exposed to gas or oil.
· Keep the top glass of the lens always clean in order to obtain the best picture quality
all the time. Be careful not to be stained by fingerprint.
· Please give a special attention to keep the unit from dangerous drop or
external shock during the process of transportation or handling.
· Never try to touch the camera in wet hand. It may cause an electric shock.
· Do not expose the camera to radioactivity. It causes a serious damage on the Sensor.
This publication is provided “AS IS” without warranty of any kind, either express or
implied, including but not limited to, the implied warranties of merchantability, fitness
for any particular purpose, or non-infringement of the third party's right. This
publication could include technical inaccuracies or typographical errors. Changes are
added to the information herein, at any time, for the improvements of this publication
and/or the corresponding product(s).
4 5
1. Precautions 2. Limitation of liability
In no event shall seller be liable to any party or any person, except for replacement or
reasonable maintenance of the product, for the cases, including but not limited to
below:
(1) Any damage and loss, including without limitation, direct or indirect, special,
consequential or exemplary, arising out of or relating to the product;
(2) Personal injury or any damage caused by inappropriate use or negligent operation
of the user;
(3) Unauthorized disassemble, repair or modification of the product by the user;
(4) Inconvenience or any loss arising when images are not displayed, due to any reason
or cause including any failure or problem of the product;
(5) Any problem, consequential inconvenience, or loss or damage, arising out of the
system combined by the devices of third party.
(6) Any claim or action for damages, brought by any person or organization being
photogenic subject, due to violation of privacy with the result of that surveillance-
camera's picture, including saved data, for some reason, becomes public or is used
for the purpose other than surveillance.
3. Disclaimer of warranty
67
4. Package
Camera x 1
manual x 1 Extra video output cable
x 1
L- Wrench Ø4.0 x 1 Tapping screws x3 Plastic anchor x3
I-Sniper Super Night Vision
Outdoor Camera
INSTRUCTION MANUAL
· EL-2000
Please read this manual carefully before installation and operation of the product.
5. Main Features
,6QLSHU3,;,0'36LPDJHVHQVRU
79/+(IIHFWLYH3L[HOV
0RWRUL]HG/HQV&RQWUROZLWKEXLOWLQEXWWRQIRUORFDO
FRQWURODQG56IRUUHPRWHFRQWUROWKURXJK'95
4XLFNHDV\DFFXUDWH]RRPDQGIRFXVFRQWURO
4XLFNDQGHDV\26'0HQXRSHUDWLRQ
PP0RWRUL]HG9DUL)RFDO/HQV
:'5:LGH'\QDPLF5DQJH
'''LJLWDO1RLVH5HGXFWLRQ
8SWRIW,57UXH1LJKW7LPH9LHZLQJ
,QWHOOLJHQW,5,PDJH&RPSHQVDWLRQ
,QWHOOLJHQW)XQFWLRQV
+LJKOLJKW(FOLSVH)XQFWLRQ
3ULYDF\0DVNLQJ
56,QWHUIDFH3HOFR'
,3:HDWKHUSURRI
9'&9$&1RQSRODULW\SRZHULQSXW
By Day By Night
- Day / Night Comparison
,6niper, the most accurate chip in the world,is an imaging solution created exclusively by
Pixim IRU,&Realtime.
,6QLSHUFDPHUDVGHOLYHUFOHDUGHWDLOHGLPDJHVLQUHDOZRUOGVFHQHVQLJKWDQGGD\
HYHQXQGHUFKDOOHQJLQJPL[HGOLJKWLQJFRQGLWLRQV,6QLSHUFDPHUDVKDYHEHHQFXVWRPWXQHG
ZLWKFDPHUDVHWWLQJVVSHFLILFDOO\IRU,&5HDOWLPH¶VOLQHRI'95VUHVXOWLQJLQORQJHU
UHFRUGLQJWLPHVYVQRQRSWLPL]HGUGSDUW\FDPHUDV
8 9
6. Installation 6. Installation
6-1. Installation overview 6-2. 3-Axis Adjustment
6-3. Ext-Video
6-4. Waterproof processing of cable end connection
ྙGkGGGGGGGGGGGGOPGG
GGGGU
ྚGmGGGGGGU
ྛGwGGGGGGGU
ྜGmGGGGGGGU
ྜྷGzGGGOhPSGOiPGGG{ps{GOX_W¶PGGwhuGOZ]W¶PGGG
GGGGGGGGGGGGGGU
ྞGzGGGOjPGGGyv{h{pvuGOZ]W¶PGGGGGG
GGGGG
Right turn
(Tightening) Left turn
(Loosening )
(C) (B) (A)
(C)
(B)
(A)
Mount Screw
(Ø4X30L-3EA)
Plastic Anchor
XUGwhuGZ]W¶
YUG{ps{GX_W¶
ZUGyv{h{pvuGZ]W¶
PAN 360°
ROTATION 360°
TILT 180°
Pan bolt
Tilt bolt
Rotation bolt
Switch cover
Extra video output
- How to use
ྙG{GGGGGGG
GGGGGGGGU
ྚGjGlGGGGsjkG
GGGGtGGGGU
tGGGGGGUGOkGGGGGGGGP
ྙGpGGGGGGGGGGGGGGG
GGGGU
ྚGjGGGGGGOwTwVnTnPU
ྛGiGGGGGGGUG~GkjTqGGSG
GGGGGGkjTkjGU
ྜGjGGGGyz[_\GGOyz[_\Rซ{yRGVyz[_\TGซ{yTP
ྜྷG{GGiujTiujGU
a. Power cable
b. RS-485 : Same as above
c.Video output cable
(Red)
(Black)
* Caution
Please make sure to seal these places with a tape
tightly enough to prevent water smearing into the
cable.
A lot of actual damages are happening by doing
improper finish on the spot.
10
7. Tips for quick installation
OSD KEY
EXTRA VIDEO
OUTPUT
RS485+
RS485-
7-1. Quick control to Zoom & Focus
7-2. RS485 Connection
- Push up or down the Tact SW (OSD Key)
by finger for a second
·G|G˧GG
·GkG˥GG
·GsGVGyG˩GmGV
RS485 +
RS485 - or
Keypad controller DVR
GGGGGvzkGGGGGGk}yGGGGU
11
8-1. OSD Menu Tree
8-2. Setting up the menu
8. Functions and operation
I-SNIPER
WDR CONTROL LOW NORMAL MIDDLE HIGH
BLC OFF ON
AGC LOW NORMAL HIGH
WHITE
BALANCE
ATW AWB..
FLUORESCENT OFF CRR CRR2
ICR DVR TOOL OFF EDGE SERIES MAX SERIES FLEX SERIES ELITE SERIES
RS-485.. CAMERA # PROTOCOL BAUD RATE RETURN.
FLIP OFF BOTH VERT HORIZ
SAVE&EXIT DEFAULT CANCEL
UP
DOWN
RIGHT
Tact SW (OSD button)
LEFT
How to use OSD button (Tact SW)
· Press
TGGG
TGG
· Push up or down
TGG
·GwGGG
TGGGGGGGT
·wGG{Gz~GGGcthpuGtlu|eU
·tGGGGGG
GGGGG{Gz~GGGU
·hGGGGGGG
GG{Gz~GGG
·~GSGGGGGG˄lp{˅GGGG{Gz~GG
GGGGU
MAIN MENU SUB MENU
,&5($/7,0(
!/(166(/(&7
!:'5&21752/
!%/&
!$*&
!:+,7(%$/$1&(
!)/825(6&(17
!,&5'9572//
!56
!)/,3
!6$9((;,7!'()$8/7!&$1&(/
'&!
0(',80!
2))!
!1250$/!
!$7:!
!2))!
!2))!
!2))!
12 13
8. Functions and operation 8. Functions and operation
3.AGC(Auto Gain Control)
7.RS-485..
4.White Balance
5.Fluorescent
6.ICR DVR TOOL
LOW : Low gain limit.
NORMAL : Normal gain limit.
HIGH : High gain limit.
ATW : Auto-tracking white balance mode.
AWB : Set white balance now and lock it.
The Automatic White Balance provides an extensive Range
GGGGGGYSWWWȋrGG
XXSWWWȋrGGGGGGiG
red or blue in varying light conditions.
Color Rolling Reduction.
,&5($/7,0(
!:'5&21752/
!%/&
!$*&
!:+,7(%$/$1&(
!)/825(6&(17
!,&5'9572//
!56
!)/,3
!6$9((;,7!'()$8/7!&$1&(/
0(',80!
2))!
1250$/!
!$7:!
!2))!
!2))!
!2))!
,&5($/7,0(
!:'5&21752/
!%/&
!$*&
!:+,7(%$/$1&(
!)/825(6&(17
!,&5'9572//
!56
!)/,3
!6$9((;,7!'()$8/7!&$1&(/
$0(',80!
2))!
1250$/!
$7:!
!2))!
!2))!
!2))!
,&5($/7,0(
!:'5&21752/
!%/&
!$*&
!:+,7(%$/$1&(
!)/825(6&(17
!,&5'9572//
!56
!)/,3
!6$9((;,7!'()$8/7!&$1&(/
0(',80!
2))!
1250$/!
$7:!
2))!
!2))!
!2))!
OFF : Not used CRR.
CRR : This color roll reduction mode will work with manual
and auto-iris lenses. However, using it with
auto-iris lenses typically results in noticeable levels
of noise in shadows or dark areas in the image.
CRR2 : This color roll reduction mode works with
auto-iris lenses only.
Noise levels are reduced in shadows or dark areas
in the image compared to the noise levels present
when using the CRR mode,but dynamic range is
also reduced further.
,&5($/7,0(
!:'5&21752/
!%/&
!$*&
!:+,7(%$/$1&(
!)/825(6&(17
!,&5'9572//
!56
!)/,3
!6$9((;,7!'()$8/7!&$1&(/
0(',80!
2))!
1250$/!
$7:!
2))!
2))!
!2))!
Ideal setting with IC Realtime DVR series.
OFF : Default Setting.
EDGE SERIES : EDGE series.
MAX SERIES : MAX series.
FLEX SERIES : FLEX series.
ELITE SERIES : ELITE series.
CAMERA# : Available to set up from 1 to 255.
PROTOCOL : Supports PELCO-D.
BAUD RATE : Select a baud rate.(2400, 4800, 9600, 19200)
RETURN. : Move to MAIN MENU.
,&5($/7,0(
!:'5&21752/
!%/&
!$*&
!:+,7(%$/$1&(
!)/825(6&(17
!,&5'9572//
!56
!)/,3
!6$9((;,7!'()$8/7!&$1&(/
0(',80!
2))!
1250$/!
$7:!
2))!
2))!
!2))!
*How to control OSD menu over RS485 :
1) Set communication speed on the camera to 9600bps.
2) Accord the ID of the camera with the of the
DVR or PTZ controller.
The factory default ID of the camera is CAM1.
3) On the DVR or PTZ controller, press 95 then
press PRESET or IRIS OPEN.(95+PRESET : Set Preset)
4) When the MAIN MENU pops up on the screen,
move the cursor Using a joystick to the desired menu to
control. When entering a Sub menu, press IRIS OPEN
momentarily.
566(783
!&$0(5$
!35272&2/
!%$8'5$7(
!5(7851
!
3(/&2'!
!
2.BLC(Back Light Compensation)
OFF : Highlights in image are prioritized.
ON : Shadows in image are prioritized.
,&5($/7,0(
!:'5&21752/
!%/&
!$*&
!:+,7(%$/$1&(
!)/825(6&(17
!,&5'9572//
!56
!)/,3
!6$9((;,7!'()$8/7!&$1&(/
0(',80!
2))!
!1250$/!
!$7:!
!2))!
!2))!
!2))!
1.WDR(Wide Dynamic Range) CONTROL
Light level is controllable with provided easy-to-use OSD menu that enables the
camera to be ideally Set up for the most of different levels of backlit or contrast lighting
situations.
,&5($/7,0(
!:'5&21752/
!%/&
!$*&
!:+,7(%$/$1&(
!)/825(6&(17
!,&5'9572//
!56
!)/,3
!6$9((;,7!'()$8/7!&$1&(/
0(',80!
2))!
!1250$/!
!$7:!
!2))!
!2))!
!2))!
LOW : Dynamic range level similar to that of CCD cameras.
NORMAL : Suitable for most indoor scenes without windows
or difficult lighting.
MIDDLE : Suitable for normal outdoor scenes and indoor
scenes that include windows.
HIGH : Maximum setting for harsh outdoor scenes.
20 2114 15
8. Functions and operation 9. Troubleshooting
Problems Troubleshooting
Nothing appears on the screen. · Please check that the power cord and line connection
between the camera and monitor are fixed properly.
· Please check that you have properly connected VIDEO
cable to the camera VIDEO output jack.
The image on the screen is dim. ·Is lens stained with dirt? Clean your lens with soft,
clean cloth.
· Set the monitor to proper condition.
· If the camera is exposed to too strong light, change
the camera position.
The image on the screen is
dark.
· Adjust the contrast feature of the monitor.
· If you have an intermediate device,
GGGG^\ȳGVGoTG
(Please check the impedance)
The camera is not working
properly, and the surface of the
camera is hot.
· Please check that you have properly connected the
camera to an appropriate power source.
Color is not correct. ·wGGGGG~op{lGihshujlGzl{|wG
menu .
If there are problems in operating, please refer to the checklist below. If the problem
persists, please contact the agent where this product is purchased.
9.SAVE&EXIT
Saves the current settings and exits the menu.
10.DEFAULT
All the settings will be restored to the factory default.
yzT[_\UUGGGG¡U
11.CANCEL
Not saves the current settings and exits the menu.
,&5($/7,0(
!:'5&21752/
!%/&
!$*&
!:+,7(%$/$1&(
!)/825(6&(17
!,&5'9572//
!56
!)/,3
!6$9((;,7!'()$8/7!&$1&(/
0(',80!
2))!
1250$/!
$7:!
2))!
2))!
2))!
,&5($/7,0(
!:'5&21752/
!%/&
!$*&
!:+,7(%$/$1&(
!)/825(6&(17
!,&5'9572//
!56
!)/,3
!6$9((;,7!'()$8/7!&$1&(/
0(',80!
2))!
1250$/!
$7:!
2))!
2))!
2))!
,&5($/7,0(
0(',80!
2))!
1250$/!
$7:!
2))!
2))!
2))!
!:'5&21752/
!%/&
!$*&
!:+,7(%$/$1&(
!)/825(6&(17
!,&5'9572//
!56
!)/,3
!6$9((;,7!'()$8/7!&$1&(/
8.FLIP
hGGvmmSGovypSG}ly{SGiv{oU
,&5($/7,0(
!:'5&21752/
!%/&
!$*&
!:+,7(%$/$1&(
!)/825(6&(17
!,&5'9572//
!56
!)/,3
!6$9((;,7!'()$8/7!&$1&(/
0(',80!
2))!
1250$/!
$7:!
2))!
2))!
2))!
16
9. Troubleshooting
10. Dimension (mm)
Problems Troubleshooting
RS-485 communication fails. · Please check the polarity between RS-485 Control
Port and RS-485 cable.
· Please check if the initial value of the RS-485
Communication setup matches between camera and
OSD Controller or DVR.
· We recommend that you make ground connection
between camera and controller for safe communication
control.
485 Control Board Connection Port
RS-485 Control Port
(+)CONNECTION TERMINAL(TRX+)
485+
(-)CONNECTION TERMINAL(TRX-)
485-
UART MODE
RET PKTItem
Camera ID
BAUD RATE
Initial value
1 9600
8-NONE-1
ENABLE
* RS-485 Communication establishment initial value
·When RS-485 cable is not properly connected,
Please reconnect and Reboot’ is displayed.Then please
turn off the power and connect the cable again.
96
Ø96
104.3
137.3
50146.3
Ø110
21
96
17
11. Specification
* Specifications are subject to change without prior notice for improvement.
2,500
Function
IR spectrum 850nm
Viewable distance Up to 150ft at moonless night
Iris control DC
Video output 1.0Vp-p Composite 75 Ohms
Operating current 110mA / AC24V(IR Off), 250mA / AC24V(IR On)
0% to 90% RH
Measurement(mm) 110(W) x 138(H) x 272.3(D)
Weight(Approx.g)
Effective Pixels 410,000 pixels 758(H)X540(V)
H.Resolution 690HTVL effective.
Synchronization Internal
Operation Temperature -10Gto +50
Humidity
Shutter speed 1/25s ~ 1/30,720s(Global Shutter)
Gamma control 6WDQGDUGȖ
White Balance 2000°K ~ 11,000°K Auto. ATW / AWB selectable by OSD
Min.Illumination 0Lux
BLC On/Off
WDR Low / Normal / Middle / High
AGC Low / Normal / High
MTBF of IR 20,000 hours
210mA / DC12V(IR Off), 630mA / DC12V(IR On)
LENS 2.8~12mm Varifocal motorized lens(F1.4)
Power source DC12V / AC24V
S/N Ratio 50dB(AGC OFF, Weight ON)
Model EL-2000 (I-Sniper)
Image sensor 1/3" Pixim WDR digital imaging device
ICR DVR Tool Off / EDGE / MAX / FLEX / ELITE
RS485 Pelco-D
Flip Off/Horiz/Vert/Both
Fluorescent Off/CRR/CRR2
18
MEMO
19
MEMO
20
MEMO
21
MEMO
22
MEMO
23
MEMO
Other manuals for EL-2000 I-sniper
1
Table of contents
