ICS SpeedHook 853PRO User manual
853PRO Hydraulic Saw
OPERATOR’S MANUAL
Questions?ForhelpcallCesscotollfree:18008824959
853PRO OPERATOR’S MANUAL
3
TABLE OF CONTENTS
SYMBOLS & LABELS 4
SAFETY 5
TECHNICAL SPECIFICATIONS 7
SET-UP 8
OPERATION 10
MAINTENANCE
1
2
TROUBLESHOOTING
14
REFERENCE
15
853PRO OPERATOR’S MANUAL SYMBOLS & LABELS
THE FOLLOWING SYMBOLS AND DEFINITIONS ARE FOUND THROUGHOUT THIS MANUAL
AND ARE DESIGNED TO MA E YOU AWARE OF POTENTIAL HAZARDS OR UNSAFE
PRACTICES.
A potentially hazardous situation exists which, if not avoided,
could result in death or serious injury.
A potentially hazardous situation exists which, if not avoided,
may result in minor or moderate injury or property damage.
A potential situation exists which, if not avoided, may result in
product or property damage.
THE FOLLOWING SYMBOLS & LABELS MAY BE FOUND IN THIS MANUAL OR ON THE SAW
Read the operator’s manual carefully and understand the
contents before you use this equipment.
Always use:
Wear hand protection
IMPORTANT
WARNING
WARNING
CAUTION
CAUTION
operator
WARNING
853PRO OPERATOR’S MANUAL SAFETY
WARNING
WARNING
THE FOLLOWING SYMBOL APPLIES TO ALL THE ITEMS LISTED ON THIS PAGE
A potentially hazardous situation exists which, if not avoided,
could result in death or serious injury.
Diamond chain breakage can result in high-speed ejection of parts, which can result in death
or serious personal injury to operators or bystanders. The items listed below are critical to
minimizing the risk of diamond chain breakage and injury.
cover, bottom guard or guard flap. The side cover, bottom guard and guard flap provides
protection against contact with moving parts, ejected debris, broken diamond chain,
thrown water and concrete slurry.
DO NOT exceed the hydraulic flow for your saw model: 8 gpm (30 lpm) or 12 gpm (45 lpm)
at 2,500 psi (172.5 bar) hydraulic pressure.
cut.
top of the bar and return on the bottom of the bar.
Rapid pushback might occur. Ref: Most diamond segements are .225 (5.72 mm) wide.
occur.
pressure can penetrate skin. If any hydraulic flud is injected into skin seek medical
attention immediately.
Bumper
853PRO OPERATOR’S MANUAL
6
SAFETY
CAUTION
CAUTION
THE FOLLOWING SYMBOL APPLIES TO ALL ITEMS LISTED ON THIS PAGE
A potentially hazardous situation exists which, if not avoided,
may result in minor or moderate injury or property damage.
chain tensioning.
service personnel.
supply may result in excessive wear to the diamond chain, which can lead to loss of
strength and diamond chain breakage.
installed.
GENERAL SAFETY PRECAUTIONS
853PRO OPERATOR’S MANUAL TECHNICAL SPECIFICATIONS
853PRO 8 gpm (30 lpm)
853PRO 12 gpm (45 lpm)
Weight w/out bar and chain
Length
Height
Width
Hydraulic Supply
Hydraulic Fluid
Requirements (Type)
Water Pressure
Water Flow
Operating Speed
Noise Level
² ²
Torque
Horsepower
853PRO OPERATOR’S MANUAL
8
SET-UP
GUIDE BAR AND DIAMOND CHAIN INSTALLATION
853PRO OPERATOR’S MANUAL SET-UP
GUIDE BAR AND DIAMOND CHAIN INSTALLATION
853PRO OPERATOR’S MANUAL OPERATION
PRE-CUT CHEC LIST
Note: The single most important factor an operator can control to increase chain life is to
use adequate water pressure. Insufficient water supply will result in excessive wear to the
chain, which can lead to loss of strength and chain breakage.
PLANNING THE CUT
®
.
853PRO OPERATOR’S MANUAL
CUTTING TIPS
®
®
.
® ®
®
®
®
®
®
®
®
®
Note: The normal life of a guide bar is two to three diamond chains. Rebar can shorten
guide bar life.
OPERATION
853PRO OPERATOR’S MANUAL MAINTENANCE
SYSTEM CLEAN-UP
TITLE 853PRO OPERATOR’S MANUAL TITLE MAINTENANCE
STEP 1
STEP 2
®
®
NOTE
: Slurry will accumulate inside the Trantorque
®
adaptor while cutting. This can fill expansion spaces
and make it difficult to remove. To faciliate removal,
turn the hex nut counterclockwise approximately 1/8
turn, and then turn it clockwise slightly, so the hexnut
is loose. Then lightly tap the end of the ring inside the
hex nut several times with your box wrench. (This will
loosen the slurry and allow the components to slide for
removal). Continue to turn the hex nut counterclockwise
to free the sprocket and Trantorque
®
.
STEP 1
®
®
Note: Do not lubricate Trantorque
® or shaft as slippage
may occur.
STEP 2
®
®
®
®
STEP 3
® until it
®
STEP 4
®
®
®
®
STEP 5
STEP 6
®
®
Note: Do not turn around or reverse the direction of the
drive sprocket to extend sprocket tooth life. Damage to
chain or drive links may occur.
853PRO OPERATOR’S MANUAL TROUBLESHOOTING
TROUBLESHOOTING
SLOW DIAMOND CHAIN SPEED
POOR CUTTING SPEED
PREMATURE CHAIN STRETCH
CHAIN TENSIONER BREA AGE
WATER NOT FLOWING
MOTOR WON'T TURN
Further questions?
Call 800.321.1240
or
visit our website at:
icsbestway.com
853PRO OPERATOR’S MANUAL REFERENCE
APPROXIMATE CUTTING RATES
Material
Cutting Rate
INCH-FOOT DEFINITION
2
853PRO OPERATOR’S MANUAL REFERENCE
ASSUMPTIONS:
ICS, Blount Inc.
4909 SE International Way
Portland, OR 97222
Tel 800.321.1240 Fax 503.653.4393
icsbestway.com
853PRO OPERATOR'S MANUAL
Other manuals for SpeedHook 853PRO
2
Other ICS Saw manuals
