ICW Elite User manual

ICWUSA.com, Inc.
If you have any questions, please call 1-800-558-4435
SINGLE ARM ELITE
SINGLE ARM ELITE INSTRUCTIONS - rev 2/17/2011 mf
page 1
DANGER!
1. Do not attempt to adjust your Elite arm until
everything you intend to mount to the arm is
mounted.
2. Arm must be completely horizontal (extended)
before adjusting the arm’s tension. Failure to do
so will damage the arm and void the warranty.
3. Never loosen or remove any of the shoulder bolts. Doing so
will cause the arm to immediately come apart with tremendous
force, and could cause serious injury.
4. If equipment requiring AC power is mounted to this unit, have a
certifi ed electrician inspect the installation.
5. Failure to install this unit according to these instructions will void
all ICW warranties. If installed incorrectly, ICW is not liable for any
damage or injury caused by the unit.
6. Do not use power tools to adjust arm tension. MUST be adjusted
by hand.
The Elite arm contains high
pressure gas springs. The
following cautions MUST be
observed to avoid serious injury.
REMOVE ELITE ARM COVERS
TOP COVER: Remove the long arm cover by
unscrewing the two 6-32 fl athead screws in the
center of the cover using a philips head
screwdriver.
END COVERS: Remove the
end covers by unscrewing the two
10-24 fl athead screws using the 1/8 “ hex key.
MOUNT
ATTACH PIPE TO CEILING PLATE
Thread pipe into ceiling mount
and tighten set screw.
Tighten
set screw
once pipe is tightly
screwed in.
ATTACH PIPE TO ELITE ARM
Thread Elite
onto extension
pipe and tighten
set screw.
Tighten set screw
once Elite is tightly
screwed in.
IF USING CEILING MOUNT MOUNT SQUARE CEILING PLATE
Using four 1/4 x 2” lag bolt
provided in hardware bag,
secure ceiling mount to a solid
wood surface or ceiling joist.
Use square pattern or inline
pattern, always being sure
to use all 4 bolts. Run cords
through center hole or the cord
management port. Be sure to
loosen set screw BEFORE
attaching ceiling pipe.
Cord
management
holes
Loosen
set screw
in ceiling mount!
MOUNT INLINE CEILING PLATE
Firmly secure
ceiling mount to
solid ceiling joist
using four #14
wood screws
Loosen the set
screw in the
ceiling mount!
found in hardware bag,
being sure mount is level.
Be sure to loosen set screw
BEFORE attaching pipe.

ICWUSA.com, Inc.
If you have any questions, please call 1-800-558-4435
SINGLE ARM ELITE
SINGLE ARM ELITE INSTRUCTIONS - rev 2/17/2011 mf
page 2
ATTACH WALL PLATE TO WALL
Locate stud and mark top
hole, drill 11/64 pilot hole
and insert #14 screw and
tighten slightly. Using a
level, mark lower hole
and drill pilot hole, insert
#14 screw and, with
unit level, tighten both
screws.
NOTE: ICW supplies #14
wood screws. If installing
onto metal studs, you
will need to replace
with proper metal stud
fasteners.
IF USING WALL MOUNT
REMOVE ELITE FROM WALL EAR
Remove end
cover on end of
Elite Arm under
wall ear. Loosen
3/8 bolt with
provided 5mm
hex key while
using provided
9/16 wrench to
hold nylock nut
as you loosen 3/8
bolt.
5mm
9/16 wrench
(provided)
ATTACH ELITE TO WALL EAR
Pass 3/8 bolt with
bearing assembly
through wall
mount ear and into
end of Elite Arm.
Secure Elite Arm
under wall mount
using split lock
washer and nylock
nut with 9/16
wrench provided
and 5mm hex key.
9/16 wrench
(provided)
5mm
Black plastic beauty cap
ATTACH PLATE TO EAR
1/4-20
screws
Using 3/16 hex key
provided, attach
wall plate to ear
with four 1/4-20
screws provided.
IF USING POLE MOUNT
Detach the pole mount from arm using the provided
5mm hex key. Separate the two sections of the pole
mount using the provided 5/32 hex key. Place around
the pole you are mounting to and fi rmly reassemble
the pole mount.
ATTACH POLEMOUNT TO POLE

ICWUSA.com, Inc.
If you have any questions, please call 1-800-558-4435
SINGLE ARM ELITE
SINGLE ARM ELITE INSTRUCTIONS - rev 2/17/2011 mf
page 3
ATTACH PARALINK KEYBOARD TRAY
Loosen knob to adjust Paralink.
Adjust horizontally for keyboard tray
and vertically for monitor. Tighten
knobs when in desired position.
Attach the keyboard tray
to the Keyboard Mount
using the supplied 5/16-
18 socket head screw.
ADJUST BALL VESA
TENSION & HEIGHT
Use the slider knob
to loosen the slider to
adjust the height of the
monitor on the Paralink.
Adjust the pivot tension
of the ball by gently
and evenly tightening
or loosening the four
screws on the back of
the ball VESA.
Slider Knob
Pivot tension
adjustment
screws
ATTACH VESA
TO MONITOR
Using a phillips
screw driver,
attach the VESA
plate to the back
of your LCD
monitor.
ADJUST
PARALINK TILT
Adjust Monitor to desired
position with ball VESA.
Tilt your monitor 50°
in any direction. Adjust
your monitor between
portrait and landscape
by rotating ball VESA.
Adjust monitor depth
by moving the paralink
forward or back then
tighting the depth
adjustment knob.
Depth
Adjustment
Knob
IF USING PARALINK ATTACH KEYBOARD TO MONITOR
Attach the Paralink
Keyboard Mount to
the Monitor Mount
by using the 3/8-16
screw and lock washer
provided

ICWUSA.com, Inc.
If you have any questions, please call 1-800-558-4435
SINGLE ARM ELITE
SINGLE ARM ELITE INSTRUCTIONS - rev 2/17/2011 mf
page 4
RUN CORDS THROUGH ARM
Run cords through Elite end
frame and along cord channel.
MOUNT
When you
begin to place
arm covers, slip
cords through
end cover cord
ports.
Reattach black plastic
bushing around exiting
cords.
ADJUST ELITE ARM RESISTANCE
Extend the Elite
straight out as shown
before adjusting the
arm’s resistance. Be sure all
equipment is mounted on the arm
before adjusting. Use the T-handle
provided to adjust the arms’
resistance. Do not use
power tools to adjust.
ADJUST QUICKLINK TILT
Adjust Monitor to desired position
with ball VESA. Tilt your monitor 50°
in any direction. Adjust your monitor
between portrait and landscape by
rotating ball VESA. Adjust monitor
further by squeezing tilt buttons
on back of Quicklink. Depressing
either button will disengage
the locking mechanism for the
corresponding pivot providing 90
degrees of adjustment. Depressing
both buttons at once allows the
user to position both pivots
simultaneously for a total of 180
degrees of adjustment.
Tilt
Adjustment
Buttons
ATTACH VESA
TO MONITOR
Using a phillips
screw driver,
attach the VESA
plate to the back
of your LCD
monitor.
IF USING QUICKLINK
ATTACH ELITE ARM COVERS
TOP COVER: Attach the long arm cover by
screwing the two 6-32 fl athead screws in the
center of the cover using a philips head
screwdriver. DO NOT USE
POWER TOOLS IN
THIS STEP!
END COVERS: Attach the
end covers by screwing the two
10-24 fl athead screws using the 1/8 “ hex key. DO
NOT USE POWER TOOLS IN THIS STEP!
MOUNT