ICW TITAN User manual

If you have any questions, please call 1-800-558-4435
TITAN ARM INSTALLATION
T2 ARM INSTALLATION - rev 04/22/2014 pjm
Page 1 of 3
Detach the pole mount from arm using the provided
5mm hex key. Separate the two sections of the pole
mount using the provided 5/32 hex key. Place around
the pole you are mounting to and fi rmly reassemble
the pole mount.
ATTACH POLEMOUNT TO POLE
ATTACH WALL
PLATE TO WALL
Locate stud and mark top
hole, drill 11/64 pilot hole
and insert #14 screw and
tighten slightly. Using a
level, mark lower hole
and drill pilot hole, insert
#14 screw and, with
unit level, tighten both
screws. ICW supplies
#14 wood screws. If
installing onto metal
studs, you will need
to replace with proper
metal stud fasteners.
MOUNT ARM
IF USING WALL MOUNT IF USING POLE MOUNT
ATTACH DESKMOUNT TO DESK
Please follow cable management
instructions before securing desk mount.
Drill a 3/8 hole through the
horizontal surface you intend to
mount to. Screw the 3/8 stud into
your desk mount as shown, the
stud is found in your hardware
bag.
Push the 3/8 stud on desk mount
through the hole in the desk and
slip the large mounting washer
over the stud from underneath
and secure in place with the 3/8
nylock nut.
Remember to detach
desk mount and feed
cords down through
the groove in the
desk mount - passing
through the bearing.
Then Re-attach desk
mount.
IF USING
DESK MOUNT
IF USING
WALL TRACK
MOUNT WALL
TRACK TO WALL
Using a phillips
drive, remove
the plastic cap
on one end of
the track. Save
this cap to put
back on when
everything is
fi nished.
Locate the wall stud and
mark the top hole of the Wall
Track, drill 11/64 pilot hole
and insert #14 screw and
tighten slightly. Use a level,
mark the 7 lower holes, drill
pilot holes and then insert the
#14 screws. Use all 8 center
screw holes.
NOTE: #14 Wood screws are
supplied with unit. If installing
into metal studs, you will
need to replace these with
proper metal stud fasteners

T2 ARM INSTALLATION - rev 04/22/2014 pjm
TITAN ARM INSTALLATION
Page 2 of 3
ATTACH PARALINK KEYBOARD TO MONITOR
Attach the Paralink
Keyboard Mount to the
Monitor Mount by using
the 3/8-16 screw and lock
washer provided.
IF ATTACHING TO ULTRA FLIP-UP
IF ATTACHING TO PARALINK
ATTACH FLIP UP
1.Remove screws from
drop extension using
5/32” hex key.
2.Align holes in keyboard
tray with screw holes in
drop extension.
3.Attach keyboard tray
using the provided
screws.
ATTACH PARALINK
1.Remove beauty cap on
Paralink.
2.Remove screw using 3/16”
hex key.
3.Slide keyboard tray into
Paralink.
4.Replace screw and tighten.
5.Replace beauty cap.
Beauty cap
Screw
MOUNT MONITOR
ATTACH KEYBOARD TRAY
ADJUST BALL VESA
TENSION & HEIGHT
Use the slider knob to
loosen the slider to adjust
the height of the monitor
on the Paralink.
Adjust the pivot tension
of the ball by gently and
evenly tightening or
loosening the four screws
on the back of the ball
VESA.
Slider Knob
Pivot tension
adjustment
screws
ADJUST
PARALINK TILT
Adjust monitor to desired
position with ball VESA.
Tilt your monitor 50°
in any direction. Adjust
your monitor between
portrait and landscape
by rotating ball VESA.
Adjust monitor depth
by moving the paralink
forward or back then
tighting the depth
adjustment knob.
Depth
Adjustment
Knob
ATTACH VESA TO MONITOR
( PARALINK )
Attach VESA
to monitor
using four 4mm
screws in the
hardware bag.

TITAN ARM INSTALLATION
TITAN ARM INSTALLATION
T2 ARM INSTALLATION - rev 04/22/2014 pjm
Page 3 of 3
MANAGE CABLES THROUGH ARM
• Using the Chrome 5mm hex key
provided, disassemble arm as shown
and lay out on a fl at surface.
• Feed computer monitor cords and any
other cords through upper arm, lower
arm, wall mount and all bearings. When
feeding cords through arms, keep them
all to one side of bolts at arm joints.
• Pass cords through slots in monitor
mount base plate and re-attach monitor
mount to front arm.
• Once all cords have been passed
through the arms, reattach arms in the
same order as they were disassembled
using the Chrome 5mm hex key.
• Torque bolts down to 204 in/lbs (17 ft/lbs)
Cable slots in
monitor mount
base plate
NOTE: When measuring
for length of cords, be sure
to allow enough extra cord
to accommodate tilt and
rotation of monitor.
NOTE: CORDS CAN BE
DAMAGED IF JOINTS
ARE ROTATED MORE
THAN 360 DEGREES.
Bearing
Wall mount
Paralink
WARNING: When
disassembling the arms,
the Chrome 5mm hex
key must be used. If a
smaller hex key is used,
the bolt will strip.
ADJUST ROTATION LIMITS - WALL MOUNT
The rotation limits for
the arm are set by
placing the stop pins in
the hole corresponding
to where you want
the arm to stop. The
stop pin then collides
with the stop screw
under the wall mount
ear, stopping the arm.
The stop pins can be
removed and set by
hand.
Stop Pin
Stop Pin
Rotation
Limiter
Ring
Stop Screw
(under wall ear)
Stop Pin