Ideal Pet Products 150 Series User manual

150 Series™
Installation
Instructions
nsulated
Iatio Pet Door
P
inylinyl
Vinyl
V
For: 78”– 86”– 94” Tall Door
Patent Pending

Before You Get Started...
•It is important to read all instructions carefully and make sure you have all the parts listed
below before you begin.
•Your pet door may be installed on the right or left side depending on which way your
sliding door opens (see bottom of page 6).
•There are several lock styles for vinyl sliding doors. See page 4 to determine which lock
you have.
•If you need help with any part of the installation, call one of our associates Toll Free at
[phone] (M–F, 9 am to 4 pm, PST) and they will be happy to help you free of charge.
TOOLS REQUIRED – Pencil, Ruler, Tape Measure, Scissors, Power Screw Driver (Phillips
Head), Hand Screw Driver (Phillips Head), Hacksaw and Utility Knife.
Page 1
1. Hangers (2)
with Screws (4)
(POLY BAG #1)
4. "H" Top Section (1) with
Optional Slide Shims (2)
& Screws (2)
2. Track Fillers (2)
(POLY BAG #1)
3. Lock Catch (2)
with Screws (4)
(POLY BAG #2)
5. Spacers (4)
(POLY BAG #2)
6. Door Seal Extrusions (2)
(78” long ea. pc.)
7. Draft•Stopper™
(1) Roll (78” long)
PARTS LIST –
WARNING: SCREWS PROVIDED ARE SELF-TAPPING, NO DRILLING REQUIRED.
DO NOT USE DRILL BITS IN ANY PART OF THIS INSTALLATION.
8. Lock Button Override (1)
(see page 4)
(POLY BAG #2)
In Pictures, Some Parts Shown In Black. Actual Parts May Be White.

Installing Your 150 Series™V.I.P. Pet Door
Step #1-Mounting Pet Door to Sliding Door Frame
IMPORTANT: BEFORE YOU START YOUR INSTALLATION—
You must remove the existing Lock Catch plate from your sliding door frame
as it will interfere with your new pet door. (see Picture #1)
NOTE: Your new pet door comes with two (top and bottom)
Mounting Hangers attached. Please leave these Hangers in place.
(see Pictures #2 and #3)
Poly Bag #1 contains two additional “Hangers”
and four 1/4” Mounting Screws.
Place one of the “Hangers” on bottom rail as
shown in Picture #4 and attach through PVC
and frame using two of the screws.
Carefully remove "H" Top Section from top
of door. (see Picture #5) Place your pet door
in position as shown. (see Picture #6).
Make sure that the bottom Hanger on door is
interlocked with Hanger on frame. (Picture #7)
With pet door in place, mark a pencil line to
correspond with top of door on edge of
frame. (see Picture #8)
Remove pet door panel then measure down
5-1/4” and make a new pencil line, then
transfer the line which is 5-1/4” down to the
inside of frame. (see Picture #9) This new line
indicates the bottom edge of the “Top”
Hanger. Place top Hanger in frame and line
up bottom edge with pencil line.
Using screws provided in Poly Bag #1, attach the hanger to the
frame, keeping the hanger centered on frame (see Picture #10).
Place two Track Fillers underneath door (see Picture #11). Re-hang the
V.I.P. Pet Door. Fit should be snug to keep pet door from moving in track.
Top
Hanger
Page 2
1
Bottom
Hanger
2
3
4
7
5
6
8
910
11
WARNING: SCREWS PROVIDED ARE
SELF-TAPPING, NO DRILLING REQUIRED.
DO NOT USE DRILL BITS IN ANY PART
OF THIS INSTALLATION.

Continuing the Installation
Step #2-Adding "H" Section Filler
Slide "H" Section onto top of door over
the springs. (see Picture #12)
Important Note: If your sliding glass door is 83” (6’-11”)
tall you may need one extra “H” Top Section.
Call [phone], this part will be shipped to you
for a small shipping charge.
A gap of 1/4" must be left at sliding
door-side area of filler section (see
Picture #13) to clear the Door Seal
Extrusion pieces.
NOTE: Some doors may require
adjustment to the "H" Section.
You may need to cut the "H”
Section to the required length.
Measure length at V.I.P. Door (see
Picture #14) and cut with hacksaw.
(see Picture #15)
Adjustments to the "H" Section
height may be made by cutting
along desired groove with a utility
knife. (see Picture #16)
After "H" Top Section is in place, secure "H" Top Section in door
using two (3/16" x 5/8”) screws provided in Poly Bag #2.
This step is optional but will add structural stability and security.
Place screws well away from glass, as shown in Picture #17.
Page 3
12
13
14
15
16
17
WARNING: SCREWS PROVIDED ARE
SELF-TAPPING, NO DRILLING REQUIRED.
DO NOT USE DRILL BITS IN ANY PART
OF THIS INSTALLATION.

Continuing the Installation
Step#3-Installing the Lock Catch
Our instructions will cover the majority of sliding door locks. If your door lock is not compatible with
the enclosed lock components, you can use an alternate method of securing your door. Please call us
Toll Free at [phone] for more information.
Page 4
Single Hook-Style
Door Lock
If
your
lock
looks
like
this...
...then
place
One
Lock
Catch
like
this.
Double
Hook-Style
Door Lock
If
your
lock
looks
like
this...
...then
place
Two
Lock
Catches
like
this.
Double Hook
Reverse-Style
Door Lock
If
your
lock
looks
like
this...
...then
place
Two
Lock
Catches
like
this.
...you will
need to
install
the Lock
Button
Override.
Peel paper off the
two-sided tape.
Position pin to
depress the lock
button and press
firmly in place.
(see Picture #18)
18
See next page
to finish lock installation.
If your sliding door lock has a small
button below the latch hook...

Continuing the Installation
Step #3-Installing the Lock Catch (continued)
Place Lock Catch onto your existing door lock hook in
the up (locked) position. (see Picture #19)
Partially close your sliding door so that you can mark the location of the top
edge of Lock Catch inside your pet door frame. (see Picture #20)
Open door, relocate Lock Catch to line up
with pencil and mark holes (see Picture
#21). Install Lock Catch using 1/4" self-
tapping screws provided in Poly Bag #2.
(see Picture #22) Use Spacer if needed.
Lock Catch has slotted holes for
adjustment if necessary.
If your sliding door has double hook-style
lock, repeat steps for second hook.
NOTE: Most sliding doors have an adjustable
locking mechanism (see Picture #23). To increase
or decrease the locking strength of your door,
turn Adjustment Screw in or out.
Page 5
19
20
21
22
23
Adjustment Screw
WARNING: SCREWS PROVIDED ARE
SELF-TAPPING, NO DRILLING REQUIRED.
DO NOT USE DRILL BITS IN ANY PART
OF THIS INSTALLATION.

Completing the Installation
Step #4-Adding Door Seal and Draft•Stopper™
Your pet door includes two Seal Extrusions which mount into the slots on the side of the V.I.P. Pet Door panel.
To properly measure for installation, close your sliding door against the pet door, measure length from top of
slider to the bottom sill of door frame.
After measuring length,
use a hacksaw to cut door
Seal Extrusions to length
(see Picture #24) and press
into slots. (see Picture #25)
The Draft•Stopper™ attaches to the moving section of your sliding glass door.
To install the Draft•Stopper™, measure the vertical distance, or height of exposed
glass, between top and bottom frames of the sliding door. Cut Draft•Stopper™
to size with scissors using this length.
Starting at top, attach Draft•Stopper™ by aligning edge so that it rubs lightly
against glass. (see Picture #26) Pull paper off tape and gently press in place
while working slowly down the Draft•Stopper™. Do not press firmly in the event
that repositioning is necessary.
NOTE: Be sure that vinyl rubs lightly against glass all the way down length of
glass. Press Draft•Stopper™ firmly in place along entire length when you are
satisfied it is correctly placed.
Reversing Pet Door Frame
If your sliding door opens “Left-to-
Right”, remove the “Ultra•Flex™”
Pet Door Frame (see Picture #27) and
reverse its position so Security Slide
(see Picture #28) faces the inside of
your home.
Page 6
24
25
26
27
28
Security Slide
Ultra•Flex™
Pet Door
Frame
Components