ARMSYSTEM–Enter“5and#”afterthreeshortbeepsthesystemisARMEDandwillautomaticallyhangup.Ifyouhear
5 rapid beeps after three short beeps, it means one of your sensors isn’t closed or is activated. The system will give you 5
seconds to enter a new code.
DISARMSYSTEM–Enter“6and#”afterabeeptheauto-dialerwillDISARMandhangup.
NOTE: Whether you receive an alarm call or you call the auto dialer, if you enter a wrong password or operation code, the call
will disconnect and sound 5 beeps on the auto-dialer. If the call was an alarm call to you, you can wait for it to call you again
(providing you have set the dialing sequence to more than one cycle) and then enter the above codes again. If your dialing
sequence is set to one cycle and you have set up the auto dialer to answer before your answering machine (if you have one
connected) then you can call into the auto dialer and enter in your codes again. If you made the initial call to the dialer you
justhavetoredialandthenenterthecodesagain.
7. HOME MODE FUNCTION:
While at home you can set your auto-dialer to Home mode. This will activate a chime every time one of the sensors is
triggered. You can also program which zone will send signals to the auto-dialer when triggered.
The factory default is ALL sensors send signals to the auto dialer.
To activate Home Mode.
• PresstheHOMEbuttononce;youwillhearachimeandthewordHOMEwillappearontheLCDscreen.
• Wait60seconds,youwillhearabeep.Systemisnowinhomemodeandwillchimeifasensoristriggered.
• Whenauto-dialerreceivessignalitwillchimeandshowwhichzoneisbeingtriggeredontheauto-dialerLCDscreen.If
thePANICbuttonispressedtheautodialerwillstartdialingthenumbersprogrammedfortheamountoftimesspecied.
• PresstheHOMEbuttonagaintoexitthehomemode.
NOTE: Arming system while in Home mode will deactivate Home mode. Press the HOME button again if you want to return to
home mode. In home mode the system will not dial out or sound alarm.
PressingthePANICbuttononthekeypadorremotecontrolwilltriggerthealarmandstartthedialingsequence.
Enabling and Disabling sensors when in home mode.
When in HOME mode all sensors will send signal to auto dialer and you will hear a chime. If you have one or more sensors
that you do not wish to activate a chime on the auto dialer you may disable the zone containing the sensor. For example, a
contactonapatiodoorthatisinzone3,ifyoudisablezone3achimewillnotsoundeachtimethedoorisopened.Zone’s
1through8control1sensorperzoneallowingforindividualcontrolof8sensors.Zone9cancontainupto8sensorsall
sensors in that zone are enabled or disabled together, you cannot pick individual sensors in that zone. The REMOTE zone
cannot be disabled. The factory preset is all sensors are on and will activate a chime when triggered.
To turn off a zone:.
• EnterpasswordfollowedbypressingtheHomebutton.
• ZoneonewillashontheLEDscreen.
• Usingthe*/UPand#/DOWNbuttonsselectthezoneyouwanttochangethesettingfor.
• PressARM/DISARMbuttontoconrm,usingthe*/UP&#/DOWNbuttonsselectONorOFF.PressARM/DISARM
buttontoconrm
• PresstheHomebuttononcetoexithome-setup.
8. VIEW STORED INFORMATION FUNCTION
Triggered Events History
The last 5 triggered Events, including the time the event occurred and the zone that was triggered are stored in memory.
To view triggered events:
• Instandbymode,press#/DOWN button
• ThetimeandzoneoftherstrecordedtriggeredeventwillbedisplayedontheLEDscreen.
• Pressingthe#/DOWNbuttonrepeatedlywillcyclethrough5storedeventsendingwiththemostrecent.
Stored Telephone Numbers
Instandbymode,press*/UPtoviewstoredtelephonenumbers.
NOTE: If no buttons are pressed for 20 seconds, the auto-dialer will automatically exit view mode.
9. BATTERY LOW LED INDICATOR
WhentheBatteryLowLEDashesonceevery1.5seconds,itindicatesthatthebatterypowerinauto-dialerisrunninglow.
Replace the batteries immediately. If batteries are low, a false signal may be triggered and the auto dialer may start dialing.
Batteriesinallunitsshouldbereplacedatleastonceayear.
