ideal-tek PCSA Series User manual

ideal-tek s.a.
manufacturer of high precision tools and instruments
PCSA CIRCUIT BOARD HOLDER

PCSA Circuit board holder
Pag. 2
work surface: 280x220 work surface: 510x220 work surface: 510x350
Additional splint:
BS-PCSS-1
Additional splint:
BS-PCSS-2-4
Additional splint:
BS-PCSS-2-4
Additional foam:
PCSA-1.2
Additional foam:
PCSA-2.2
Additional foam:
PCSA-4.2
Standard configuration:
- 2 splints (sliding rail)
- 1 central removable middle bridge
- 1 cover
- 1 foam rubber ESD safe
ideal-tek s.a.
via A. Monti 10, 6828 Balerna (switzerland) Tel. [phone] Fax [phone] [email protected] www.ideal-tek.com
PCSA-1 PCSA-2 PCSA-4

PCSA Circuit board holder
Pag. 3
PCSA-1
BRIDGE = 0 SPLINT = 2BRIDGE = 1 SPLINT = 2BRIDGE = 1 SPLINT = 4
BRIDGE = 1 SPLINT = 6
Subject to changes. The manufacturer declines any responsability for potential damages to persons or objects due to inappropriate usage.
ideal-tek s.a.
via A. Monti 10, 6828 Balerna (switzerland) Tel. [phone] Fax [phone] [email protected] www.ideal-tek.com
PCSA-2
PCSA-4
FEATURE:
- Circuit board holders of the PCSA series are the ideal tool for fitting circuit boards with components. The holder can
easily be demounted in single parts and be reassembled in different combinations.
- The standard models PCSA-1/2/4 are equipped with 1 removable middle bridge and 2 adjustable splints. Thus two work
areas can be created.
- Any circuit board holders can be fitted with additional subdivisors (4 for PCSA-1/2 and 6 for PCSA-4).
That way small circuit boards can be used on several levels.
Combinations and work surface in mm

PCSA Circuit board holder
Pag. 4
Using pc board assembly jig in vertical position
ideal-tek s.a.
via A. Monti 10, 6828 Balerna (switzerland) Tel. [phone] Fax [phone] [email protected] www.ideal-tek.com
How to use PCSA detachable assembly jigs for pc board
Sliding rails may be positioned by means of self-
locking sleeves. A system of springs makes it
possible to insert and remove printed circuit boards
without changing position of sleeves.
Turn the knob to remove the middle bridge. Moveable couplings, located on the rear side of the
assembly jigs for attaching the PC assembly jig to the
frame. These couplings keep the PC assembly jig from
detaching from the frame.
Positioning of the lower corners of the
PC Assembly Jig in the toothed guides
located on the frame.
Positioning at 70° angle Positioning at 80° angle Positioning at 90° angle
Practical use of PC Assembly Jig with PC Board in place. Unsoldering of components carried out with PC Assembly Jig in
vertical positions.
PC Assembly jig with component-press lid closed
screwed or clamped to work-top, in relation to the
height of the components.
Foam rubber-lined lid for holding components in
place. May be raised by applying pressure to front
buttons.
Easy to unslot and detach various parts. (Frame-PC
holder unit-component-Press Lid).
PC board assembly jig can be raised by turning lateral
knobs. Self-adjustment to frame at right working
angle, after unit raising.

PCSA spare parts
Pag. 5
ideal-tek s.a.
via A. Monti 10, 6828 Balerna (switzerland) Tel. [phone] Fax [phone] [email protected] www.ideal-tek.com
PCSA-1.2: Foam PCSA-2.2: Foam PCSA-4.2: Foam
PCSA-1 PCSA-2 PCSA-4
BS-PCSS-1: Sliding rail BS-PCSS-2-4: Sliding rail

PCSA spare parts
Pag. 6
ideal-tek s.a.
via A. Monti 10, 6828 Balerna (switzerland) Tel. [phone] Fax [phone] [email protected] www.ideal-tek.com
AC-PCSA: Bush-Knob-Screw SR-PCSA: Bush SR-PCSS: Bush (old) PR-PCSS: Knob
RIC-PCSA-N15: Pivot SC-PCSS: Cover clip lever
PCSA-1 PCSA-2 PCSA-4
BS-PCSS-NBS: Sliding block MO-BS-PCSS: Spring SF-BS-PCSS: Ball diam. 5 mm IN-PCSS: Cover support

PCSA
Pag. 7
Rev.03
ideal-tek s.a.
via A. Monti 10, 6828 Balerna (switzerland) Tel. [phone] Fax [phone] [email protected] www.ideal-tek.com