Supplied By www.heating spares.co Tel. 0161 620 6677
2Mexico Super FF4100 & FF4125 - Users
INSTALLATION
Safety
It is essential that the instructions in this booklet are
strictly followed, for safe and economical operation of
the boiler.
Gas Safety (Installation & Use)
Regulations or rules in force.
In your own interest, and that of safety, it is the law that this
boiler must be installed by a CORGI registered installer or in IE
a competent person, in accordance with the above regulations.
Electricity Supply
This appliance must be efficiently earthed.
Supply: 230 V ~ 50 Hz.
The fusing should be 3A.
Connection must be made in a way that allows complete
isolation of the electrical supply such as a double pole switch
having a 3mm (1/8") contact separation in both poles, or a plug
and socket, serving only the boiler and system controls. The
means of isolation must be accessible to the user after
installation.
Important Points
a. If the boiler is installed in a compartment then the
compartment MUST NOT be used for storage purposes.
b. The ventilation provided for the boiler during installation MUST
NOT be blocked, and a check should be made periodically
that the ventilation areas are free from any obstruction.
c. If it is known or suspected that a fault exists on the boiler then
it MUST NOT be used until the fault has been corrected by a
CORGI registered installer or in IE a competent person.
d. Under NO circumstances should any of the sealed components
on this appliance be used incorrectly or tampered with.
In cases of repeated or continuous shutdown a CORGI registered
person or in IE a competent person should be called to investigate
and rectify the condition causing this and carry out an operational
test after each intervention on the device. Only the manufacturer's
original parts should be used for replacement.
Minimum Clearances
A clearance of 533mm (21") MUST be available at the front of
the boiler for servicing.
The minimum clearances given in Table 1 MUST be complied
with, in order to maintain the safe running of the boiler.
To light the boiler. Refer to Frame 2
If a programmer is fitted refer to separate instructions for the
programmer before continuing.
1. Check that the electricity supply to the boiler is OFF.
2. Open the control panel drop-down door and ensure that the
thermostat knob (G) is in the OFF position.
3. Switch ON the electricity supply to the boiler and check that
all external controls, e.g. room thermostat etc., are ON.
4. Set the boiler thermostat knob (G) to position 6. The fan will
start. After the fan has run for a few seconds the pilot
solenoid valve should open and the intermittent spark
commence, continuing until the pilot is established. The
main burner will then cross-light smoothly.
Winter conditions (i.e. central heating and domestic hot
water). The thermostat should be positioned at setting 5 or 6.
Summer conditions (i.e. domestic hot water only). The
thermostat should be positioned at setting 2.
These settings are offered for general guidance only and other
settings may be found preferable, dependent upon the type of
system installed or as recommended by the installer.
Mexico Super FF4100 ............... G.C. No. 41 392 31
Mexico Super FF4125 ............... G.C. No. 41 392 32
MEXICO SUPER (Natural Gas Models Only)
Certified - P.I. No. 87 AU 83
Destination Countries: GB, IE
1 BOILER CLEARANCES Table 1
CAUTION.
To avoid the possibility of injury during the installation, servicing or cleaning of
this appliance care should be taken when handling edges of sheet steel components
Boiler Flue Dimension A
Model Length Rear Flue Side/Top flue
mm (in.) mm (in.) mm (in.)
FF4100 Up to 55 (2 1/4) 55 (2 1/4)
FF4125 600
(23 5/8)
FF4100 600 to 2000 35 35
(23 5/8 to (1 3/8) (1 3/8)
78 3/4)
FF4125 600 to
1000 55 55
(23 5/8 to (2 1/4) (2 1/4)
39 1/4)
200940-1.p65 3/2/2004, 9:07 AM46
