idi Aspect ISR Q-CARD User manual

Aspect ISR Q-CARD
SETUP/PATIENT PREPARATION:
Moving table (NEVER WITH PATIENT ON BOARD):
1) Unlock Rear Casters using Caster Lock Pedal.
2) Unlock Front Steering using Front Steer Lock Pedal.
3) Position table to desired location.
4) Secure table mobility by locking Casters and front
steering using Rear Caster Lock Pedal and Front Steer
Lock Pedal.
AC Power:
5) Plug power cord into properly grounded outlet.
6) Protect power cord from damage by casters or other
equipment.
Controls:
1) Emergency Stop Pushbutton disables all tabletop motion
control when engaged.
2) If tabletop motion controls fail to operate, make sure
that the Emergency Stop Pushbutton is NOT pushed in.
BATTERY OPERATION (DC POWER):
1) The table is FULLY functional, but motions are slower.
2) Connect to AC power for a minimum of 8 hours daily to
ensure a proper battery charge.
3) Failure to push in Emergency Stop Pushbutton when
table is not in use and not connected to AC power for
longer than 72 hours, may result in permanent damage
to the batteries.
CPR:
Return table to level, retract tabletop to minimize
overhang and lower table position to a comfortable
height to perform CPR.
CLEANING AND STORAGE:
1) Unplug power cord and wrap it around
the cord holder.
2) Push in Emergency Stop Pushbutton.
3) Lock rear casters and front steering.
4) Clean and disinfect table.
WARNING! Read operator
manual prior to use
BRAKES:
The ISR table braking system utilizes a passive magnetic brake; it
remains engaged in the event of a complete loss of electrical power.
Power is necessary to release brakes.
Braking force is limited by the magnet strength. Use caution when
applying pressure to the side of the table as the brakes may be
overcome if more than 50 pounds of force is applied.
To reduce potential motion during patient transfers with larger
patients, release the table brake and move the top in the direction
the patient will be pulled during loading or unloading until the
tabletop transverse travel limit is reached. Release the panning
handle to re-engage the lock and then transfer the patient.
Scan to
Access
User
Manuals
Online
IMAGING END
OF TABLETOP
CONNECTION PORT FOR
HAND OR FOOT CONTROLS
CONNECT HERE
EMERGENCY
STOP
PUSHBUTTON
POWER CORD
HOLDER
PEDESTAL END OF TABLETOP
FRONT STEER
LOCK PEDAL
REAR CASTER LOCK PEDAL

It is recommended that the pendant
control be disconnected during critical
procedures to prevent inadvertent
operation or motion, causing patient
injury.
CASTER LOCK/STEER
PEDAL POSITIONS
•PUSH IN to stop
ALL tabletop motion.
•TWIST to reset.
ELEVATE
SWITCH
TRENDELENBURG
SWITCH
(Green light to right
of switch indicates
tabletop is level for
this motion)
Green light to
right of switch
indicates
tabletop is level
for this motion)
ISO-ROLL
SWITCH
PANHANDLE
KNOB/ TABLETOP
FLOAT BRAKE
(Lift underside of
Panhandle Knob to
float tabletop. It will
not operate if
tabletop is not level)
L100-2859 Rev.E
Tabletop Motion
Handset Control
Patients must be loaded from the side of table. Tilting or instability may occur if
patient is loaded onto the pedestal end of table or the imaging end of the table.
EMERGENCY STOP PUSHBUTTON
(Green light to
right of Tabletop
Float Brake
indicates tabletop
is centered on the
base laterally)
TABLETOP MOTION
CONTROL PANHANDLE
Elevate
Tilt up Imaging
End
(Trendelenburg)
Trendelenburg
Level Indicator
ISO-Roll
Clockwise
Laterally
Centered
Indicator
Lower
Tilt Down
Imaging End
(Trendelenburg)
ISO-Roll Level
Indicator
ISO-Roll
Counter-
Clockwise
Aspect ISR Q-CARD
LOCK
PRESS FORWARD ON TOP HALF
OF PEDAL TO LOCK ALL
MOVEMENT
UNLOCK
PRESS DOWN ON
BOTTOM HALF OF PEDAL
TO ALLOW REAR CASTERS
TO SWIVEL FREELY
STEER LOCK
PRESS DOWN ON PEDAL TO
RESTRICT FRONT MOVEMENT TO
FORWARD AND BACKWARDS ONLY
FLOAT POSITION
PULL UP ON PEDAL TO ENABLE
MOVEMENT OF FRONT IN ALL
DIRECTIONS