iDiPOS AB-88H User manual

MAN U A L R E V IS IO N E N 1 . 1
M IN I T h e rm a l P rinte r
U S E R 'S M A N U A L
A B - 8 8 H

You must use the only supplied adapter. It is
dangerous to use other adapters.
Make sure the printer power is off before
plug or unplug the cable.
Please don’t place the printer in
humidity or dusty space because
excessive humidity and dust may
damage it.
Do not put foods or drinks on the
printer, in case that splash into
the printer.
The print head has a high temperature
after work. Please don t touch the
print head or touch the motor shell
in case scalded.
NOTICE
Do not fall the printer down and avoid
vigorously impact.
Do not plug or unplug with your hands
wet. You may be electrocuted.
Avoid magnetic objects near the printer.
Do not put printer on unstable surface.
Don t use tweezers, knife,
screwdriver or other hard objects
to touch the heating piece; for the
heating piece will hurt you eternally.
’
’If there appears any abnormal noise, smoke etc, please power off the
machine and unplug power at once. Please ask after-sarle service for
help.
NOTICE

0 1
微型热敏打印机
用户手册
AB-88 IV
保修 卡
USB
Pictures for reference only.
User's Manual/Warranty Card
Chapter 1 Packing List
Your printer box should include these items.
Table of Contents
Chapter 1 Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .01
Chapter 2 Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .02
Chapter 3 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .03
3.1 Printer Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . .. . 03
3.2 Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .03
Chapter 4 Usage Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .04
4.1 Connect the cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .. . . 04
4.2 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04
4.3 Installing the Roll Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05
4.4 Installing Oil Proof Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .06
4.5 Paper Jam Caused By Cutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06
4.6 Self-Test and DUMP Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .07
4.7 DIP Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . 08
4.8 Interface Explanation Interface Explanation . . . . . . . . . . . . . . . . 10
4.8.1 RS -232 Serial Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.8.2 USB Interfacet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
4.8.3 Ethernet Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.8.4 Cash Drawer Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . .11
1. Printer
2. User's Manual/Warranty Card
3. Paper Roll
4. RS232 Interface Cable
5. AC Adapter
6. AC power cable
7. Oil Proof Cover
8. USB Cable
Printer
Paper Roll
RS232 Interface Cable
AC Adapter
AC power cable
Oil Proof Cover
USB Cable

0 2 0 3
3.1
3.2
12
35
4
6
7
8
910 11
12
Notice: The printing speed relates with data transporting, command control
and power voltage etc.
Chapter 2 Specification Chapter 3 Product Overview
3.1 Printer Parts
3.2 Interfaces
1. Cover Opener
2. Printer Cover
3. Paper Cabin
4. Cutter Cover
5. Printer Head
6. Control Panel
7. Power Button
8. Power Plug Port
9. Cash Drawer Interface
10. Ethernet Port
11. USB Port
12. RS232 Interface
Printing
Dimensions
Paper
Reliability
Usage
conditions
Printing Method
Printing Speed
Resolution
Paper Supply Mode
Language
Interface
Pringing width
Character Size
Character Per Line
Barcodes
Driver
Sensor
Receive Buffer Size
Mass
W×D×H
Paper type
Width
Diameter
Printer head life
Autocutter
Power supply
Operating
Storage
Thermal line printing
Max 250 mm/sec
203 DPI
Easy paper loading
User language supported
72 mm
Font A:12×24
Font B:9×17
Code 39,Code 128,EAN 8,EAN 13
Windows 2000/XP/2003 Server/VISTA/7
Out of paper
4K Bytes
Approx.1.45 kg
146×196×152mm
Thermal Paper
79.5±0.5 mm
Max.￠80 mm
Approx. 100 km (pringting rate 12.5% or less)
500,000 cuts
24 VDC ± 10%
5℃~45℃，20~85%RH
-10℃~50℃，10~90%RH(the paper is not included)
RS-232 / USB / Ethernet
42/48/53

4.1
4.2
0 4 0 5
POWER
ERROR
FEED
4.3
4.5
4.4
4.6
Chapter 4 Usage Description
4.1 Connection the Cables
4.2 Using the Printer
Serial Connector Cable
USB Connector Cable
Ethernet Connector Cable
Drawer kick-out Cable
Power Supply Cable
POWER INDICATING LIGHT
Power on the printer, power lights; power off, light off.
ERROR INDICATING LIGHT
The light is on when the printer is lack of paper; the light will flash when the
printer cover installs not well or Online error.
FEED
Press the FEED button once to advance paper one line. You can also hold
down the FEED button to feed paper continuously.
4.3 Install the Roll Paper
1. Make sure that the printer is not receiving data before replacing the roll paper;
otherwise, data may be lost.
2. Upward the” PULL” buckle handle till the cover open.
3. Remove the used paper roll core.
4. Put into new paper roll. As picture 4.4shows.
5. Be sure the correct direction of the paper comes off the roll.
6. Pull out a small amount of paper, and then close the cover. As picture 4.5shows.
Fr ont
Paper end direction:

0 6 0 7
4.7
4.8
4.9
4.4
The printer is an Oil Proof Cover supplied. It’s used to prevent water
splashing into the inside of the printer and not oil-water corrosion and
oxidation protection to the internal electronic components, which
extends the life of the printer.
Installation method:
Put the Oil Proof Cover onto the printer cover as the picture4.7 shows.
Installing Oil Proof Cover
4.5 Paper Jam Caused By Cutter
1. If the paper is thick or sudden lack of power when cutting, paper jam might
appear.(cutter cannot reset)
2. Normally the cutter will reset when repowered, if the cutter did not reset,
users could follow below steps to solve the problem.
① Take away the cutter cover as below picture4.8 shows.
② Stir the cutter gear till the cutter moves to the Initial position as picture4.9
shows.
4.6 Self-Test and DUMP Mode
1. Press "FEED" button and hold on when powering on the printer, the
printer will perform self-test.
2. Power off the printer and take out the paper roll. Then press "FEED"
button and hold on and power on the printer. Then put in the paper
roll and close the printer cover. The printer will print out "DUMP".
That means the printer enters in DUMP mode. All data will be printed
out in raw hex format.
Back to normal mode: restart the printer could put the printer in normal
mode.

0 8 0 9
1 2 3 4 5 6 7 8
JAE46
ON
1 2 3 4 5 6 7 8
ON DIP
4.11
4.10
DIP switches could perform printer configurations as follows: COM port baud
rate adjusting, beep alarm switch, printing density adjusting, parity selection
(for serial communication), parallel printing server mode or normal mode
adjusting , EPSON mode or 64character mode switching, Chinese Character
double byte mode or English character single byte mode selection.
Below are lists of DIP configurations:
Baud rate adjusting:
4.7 DIP Switch
1)Unscrew the screw on bottom of printer and take away the metal cover as
the picture 4.10shows.
2)Users will find the DIP switches under the window as the picture 4.11shows.
DIP5
ON
OFF
Beep Density
Enable
Disable
Default
▲
Default
▲
Dark
Light
DIP6
ON
OFF
DIP7
ON
OFF ▲
Printing speed
FAST
Byte Mode
Double-Byte Mode
SingleByte Mode
▲
DIP8
ON
OFF
Default
Default
SLOW
▲
Baud Rate DIP2
OFF
ON
OFF
ON
Default
9600bps
1920bps
38400bps
115200bps
DIP1
OFF
OFF
ON
ON
▲
Character per line
42
48
Reserved
53
DIP3
OFF
OFF
ON
ON
DIP4
OFF
ON
ON
OFF
Default

1 0 1 1
16
4.8.1 RS-232 Serial Interface
4.8 Interface Explanation
Signal configuration for communication with PC host:
Printer serial port is DB9, baud rate supports 9600, 19200, 38400, 115200 bps,
8 bits data word length, 1 stop bit, no parity settings.
Descriptions to interface signals:
TXD
RXD
RTS
DTR
-
-
-
-
GND -
--
Pin No. Signal name Direction Function
1
2
3
4
5
6
7
8
Output
Intput
Intput
Output
Transmit Data
-
Receive Data
-
Signal Ground
Ready To Sen
Clear To send
4.8.2 USB Interface
USB port uses Type B plug and support USB1.0 and USB2.0. Signals are as
below:
PIN
1
2
3
4
Signal Name
VCC
D-
D+
GND
Direction
+ 5V DC
Data -
Data +
Ground
Ethernet port uses RJ45 port with 10M ability. Configurations are as below:
4.8.3 Ethernet Interface
4.8.4 Drawer Connector Interface
-
-
-
- -
- -
Signal name Direction
Frame ground
Input
Open cash drawer
Signal ground
Signal Name
TX+
TX-
RX+
n/c
n/c
RX-
n/c
nc
Pin No.
1
2
3
4
5
6
7
8
Description
Tranceive Data+
Tranceive Data+
Receive Data+
Not connected
Not connected
Receive Data-
Not connected
Not connected
Pin No.
1
2
3
4
5
6
+24V
(TXD)
(RXD)
(RTS)
2
3
8
(TXD)
(RXD)
(CTS)
3
2
8
(GND)
(DTR)
5
6(DSR)
(GND)
5
6
PRINTER
SIDE
HOST
SIDE