IEC E055-71520301 User manual

OWNER'S MANUAL
Auto-Changeover is available in 4-pipe systems,
in 2-pipe systems with Electric Heat, or when
used with G100-71520306 accessory, auto-
changeover sensor.
FAN COIL
NON-PROGRAMMABLE
DIGITAL THERMOSTAT
Copyright 2008, International
Environmental Corp. All Rights Reserved
72
74
70
COOL
HEAT
AUTO
2- or 4-pipe configurable
Dual or Single Setpoint
Very easy to program
Large, easy to read display
Thermoglow Backlight
No batteries required
Auto-Changeover
Locking Keypad
P/N E055-71520301
P/N E055-71520304

P/N E055-71520301 and P/N E055-71520304
Table Of Contents
FRONT PANEL
DISPLAY
BASIC OPERATION
ADVANCED SETUP
ABOUT ADVANCED FEATURES
& OPERATION
WARRANTY
2
3
9
10
16
25
Page 1
CAUTION
WARNING
SELECTING THE HEAT
OR COOL MODE
5
Follow Installation Instructions
carefully. Disconnect Power
to the Heater/Air Conditioner
before removing the old therm-
ostat and installing the new
thermostat.
Copyright 2007, International
Environmental Corp. All Rights Reserved

P/N E055-71520301 and P/N E055-71520304
Table Of Contents
FRONT PANEL
DISPLAY
BASIC OPERATION
ADVANCED SETUP
ABOUT ADVANCED FEATURES
& OPERATION
WARRANTY
2
3
9
10
16
25
Page 1
CAUTION
WARNING
SELECTING THE HEAT
OR COOL MODE
5
Follow Installation Instructions
carefully. Disconnect Power
to the Heater/Air Conditioner
before removing the old therm-
ostat and installing the new
thermostat.
Copyright 2007, International
Environmental Corp. All Rights Reserved

72
74
70
COOL
HEAT
AUTO
Front Panel
Page 2
Liquid Crystal Display
with Thermoglow
Up/Down Buttons
Mode Button
Fan/Override Button
Heat or Cool Indicator
Heat = Red, Cool = Green
1
1
2
3
4
5
2
3
45
Display
OUTSIDE
unoccupied
1
2
3
4
Mode Indicators - Page 5-8
Selects the operational mode of the equipment.
HEAT - Indicates the heating mode.
COOL - Indicates the cooling mode.
AUTO - Indicates the system will automatically
changeover between heat and cool modes
as the temperature varies.
OFF - Indicates heating and cooling are turned off.
Room Temperature Display
Indicates current room temperature.
Desired Set Temperature - Page 9
Indicates desired room temperature(s).
Setup icon - Pages 10-14
Indicates the thermostat is in the advanced setup
mode.
1
1
1
2
3
4
3
Page 3

72
74
70
COOL
HEAT
AUTO
Front Panel
Page 2
Liquid Crystal Display
with Thermoglow
Up/Down Buttons
Mode Button
Fan/Override Button
Heat or Cool Indicator
Heat = Red, Cool = Green
1
1
2
3
4
5
2
3
45
Display
OUTSIDE
unoccupied
1
2
3
4
Mode Indicators - Page 5-8
Selects the operational mode of the equipment.
HEAT - Indicates the heating mode.
COOL - Indicates the cooling mode.
AUTO - Indicates the system will automatically
changeover between heat and cool modes
as the temperature varies.
OFF - Indicates heating and cooling are turned off.
Room Temperature Display
Indicates current room temperature.
Desired Set Temperature - Page 9
Indicates desired room temperature(s).
Setup icon - Pages 10-14
Indicates the thermostat is in the advanced setup
mode.
1
1
1
2
3
4
3
Page 3

Display
OUTSIDE
unoccupied
5
6
7
8
5
6
7
8
Fan icon - Page 9
Indicates fan operation.
Fan = low speed
Fan = medium speed
Fan = high speed
When only the Fan icon is displayed, the fan is in
the Auto mode and will run only when necessary to
heat or cool.
Locked icon - Page 21
Indicates keypad has been locked.
Outside icon - Pages 13 & 22
Indicates the temperature displayed is from the
optional outside sensor.
Unoccupied icons - Pages 13-14
Indicates a dry contact forced Unoccupied time
period is in effect.
Page 4
70 68
HEAT
70
76
COOL
70
76
68
COOL
HEAT
AUTO
70
OFF
Press
MODE
Press
Press
MODE
MODE
Page 5
The HEAT setting indicates
the temperature the room
has to reach before the
heating source will turn
on to heat the room.
Heating Only
The COOL setting indicates
the temperature the room
has to reach before the
cooling source will turn
on to cool the room.
Cooling Only
OFF indicates both heating
and cooling are turned off.
Off
AUTO will automatically
select heat or cool based
on room temperature
demand.
Heating or Cooling
Select Mode by Pressing the MODE Button
Selecting the Heat or Cool Mode 4-Pipe Operation

Display
OUTSIDE
unoccupied
5
6
7
8
5
6
7
8
Fan icon - Page 9
Indicates fan operation.
Fan = low speed
Fan = medium speed
Fan = high speed
When only the Fan icon is displayed, the fan is in
the Auto mode and will run only when necessary to
heat or cool.
Locked icon - Page 21
Indicates keypad has been locked.
Outside icon - Pages 13 & 22
Indicates the temperature displayed is from the
optional outside sensor.
Unoccupied icons - Pages 13-14
Indicates a dry contact forced Unoccupied time
period is in effect.
Page 4
70 68
HEAT
70
76
COOL
70
76
68
COOL
HEAT
AUTO
70
OFF
Press
MODE
Press
Press
MODE
MODE
Page 5
The HEAT setting indicates
the temperature the room
has to reach before the
heating source will turn
on to heat the room.
Heating Only
The COOL setting indicates
the temperature the room
has to reach before the
cooling source will turn
on to cool the room.
Cooling Only
OFF indicates both heating
and cooling are turned off.
Off
AUTO will automatically
select heat or cool based
on room temperature
demand.
Heating or Cooling
Select Mode by Pressing the MODE Button
Selecting the Heat or Cool Mode 4-Pipe Operation

Heat Only
Step #4 = 1 in the Advanced Setup section,
page 11.
70 68
HEAT
70
OFF
Press
MODE
Selecting the Heat or Cool Mode 2-Pipe Operation
The HEAT setting indicates
the temperature the room
has to reach before the
heating source will turn
on to heat the room.
Heating Only
OFF indicates both heating
and cooling are turned off.
Off
Page 6
Cool Only
Step #4 = 2 in the Advanced Setup section,
page 11.
70
OFF
Press
MODE
70
76
COOL
Selecting the Heat or Cool Mode 2-Pipe Operation
The COOL setting indicates
the temperature the room
has to reach before the
cooling source will turn
on to cool the room.
Cooling Only
OFF indicates both heating
and cooling are turned off.
Off
Page 7

Heat Only
Step #4 = 1 in the Advanced Setup section,
page 11.
70 68
HEAT
70
OFF
Press
MODE
Selecting the Heat or Cool Mode 2-Pipe Operation
The HEAT setting indicates
the temperature the room
has to reach before the
heating source will turn
on to heat the room.
Heating Only
OFF indicates both heating
and cooling are turned off.
Off
Page 6
Cool Only
Step #4 = 2 in the Advanced Setup section,
page 11.
70
OFF
Press
MODE
70
76
COOL
Selecting the Heat or Cool Mode 2-Pipe Operation
The COOL setting indicates
the temperature the room
has to reach before the
cooling source will turn
on to cool the room.
Cooling Only
OFF indicates both heating
and cooling are turned off.
Off
Page 7

HEAT indicates the temperature
the room has to reach before the
heating source energizes. If the
water supply is cold, this screen
and heating would be locked out.
COOL indicates the temperature
the room has to reach before the
cooling source energizes. If the
water supply is hot, this screen
and cooling would be locked out.
70
OFF
Press
MODE
Press
Press
MODE
MODE
Page 8
70 69
70
72
Note: If the water temperature is changed during the
year, the thermostat will then automatically lock out the
incorrect mode.
Heating and/or Cooling
Step #4 = 3 in Advanced Setup (page 11), and the
accessory changeover sensor (G100-71520306) is used.
Step #4 = 4 or 5 in Advanced Setup (page 11).
Operation is the same as a 4-pipe system (page 5).
Selecting the Heat or Cool Mode 2-Pipe Operation
70
72
69
If step #4 = 3, this
screen will not appear.
AUTO will automatically select
heat or cool based on the room
temperature demand.
OFF indicates both heating
and cooling are turned off.
Selecting Your Desired Temperature
(adjusting the setpoints)
Basic Operation
70
76
68
COOL
HEAT
AUTO
AUTO OR PROGRAM MODE
Pressing the UP or DOWN button in Auto or Program
mode will adjust both the heat and cool set temperatures
simultaneously.
buttons.
Adjust the desired
set temperature with the
Fan Operation
Press
FAN
Press
FAN
Press
FAN
Press
FAN
Press
FAN
Low Speed Medium Speed High Speed Auto
Fan
Pressing the FAN button will run the fan in
low, medium, or high speed continuously
(see below and page 20).
When only the Fan icon is displayed, the fan
is in the Auto mode and will run only when
necessary to heat or cool (see below and
page 20).
Note: If the thermostat is placed in the Off mode, the fan
will de-energize (see page 5).
Fan Fan Fan
Page 9

HEAT indicates the temperature
the room has to reach before the
heating source energizes. If the
water supply is cold, this screen
and heating would be locked out.
COOL indicates the temperature
the room has to reach before the
cooling source energizes. If the
water supply is hot, this screen
and cooling would be locked out.
70
OFF
Press
MODE
Press
Press
MODE
MODE
Page 8
70 69
70
72
Note: If the water temperature is changed during the
year, the thermostat will then automatically lock out the
incorrect mode.
Heating and/or Cooling
Step #4 = 3 in Advanced Setup (page 11), and the
accessory changeover sensor (G100-71520306) is used.
Step #4 = 4 or 5 in Advanced Setup (page 11).
Operation is the same as a 4-pipe system (page 5).
Selecting the Heat or Cool Mode 2-Pipe Operation
70
72
69
If step #4 = 3, this
screen will not appear.
AUTO will automatically select
heat or cool based on the room
temperature demand.
OFF indicates both heating
and cooling are turned off.
Selecting Your Desired Temperature
(adjusting the setpoints)
Basic Operation
70
76
68
COOL
HEAT
AUTO
AUTO OR PROGRAM MODE
Pressing the UP or DOWN button in Auto or Program
mode will adjust both the heat and cool set temperatures
simultaneously.
buttons.
Adjust the desired
set temperature with the
Fan Operation
Press
FAN
Press
FAN
Press
FAN
Press
FAN
Press
FAN
Low Speed Medium Speed High Speed Auto
Fan
Pressing the FAN button will run the fan in
low, medium, or high speed continuously
(see below and page 20).
When only the Fan icon is displayed, the fan
is in the Auto mode and will run only when
necessary to heat or cool (see below and
page 20).
Note: If the thermostat is placed in the Off mode, the fan
will de-energize (see page 5).
Fan Fan Fan
Page 9

Press
Select Display operation:
On = Full Display
Off = Minimal display
Display On
Display Off See Page 20
MODE
NOTE: Each step
# is located at the
top right corner of
the display for easy
reference.
Press the MODE and
FAN buttons at the
same time for 10
seconds to enter
Advanced Setup
screens.
Advanced Setup
MODE FAN
I
ON
Setup
Press
MODE
Continued
Page 10
Select Display operation:
1 = Single Setpoint
2 = Dual Setpoint
See Page 24
cooling setpoint will always be displayed. To
display the room temperature, press and hold
the MODE button for two seconds. The
degree icon will blink when the large number
is displaying room temperature and will
remain solid when displaying the heating or
cooling setpoint.
2
Setup
2
Note: When Single Setpoint
is selected, the heating or
Advanced Setup
Select fan coil system
type:
2 = 2-pipe fan coil
4 = 4-pipe fan coil
4
2
Step #4 only appears if step #3 = 2.
2-PIPE SYSTEM OPERATION
1= Heat only system
2= Cool only system
3= Heat/Cool Auto
changeover
4= Heat/Cool Aux Electric
heat, Lockout Electric Heat
when Hot Water is available
5= Heat/Cool total electric
heat, no Hot Water, only
Electric Heat.
Note: #3 & #4 require accessory
changeover sensor
4
3
Setup
Press
MODE
Press
MODE
Continued
I
4
Setup
Page 11
On
Off
See Page 20, Note #2
Select operation when
fan is in the Auto mode:
On = continuous low
speed fan
Off = only energize
during a heating or
cooling cycle.
5
AUTO
Press
MODE

Press
Select Display operation:
On = Full Display
Off = Minimal display
Display On
Display Off See Page 20
MODE
NOTE: Each step
# is located at the
top right corner of
the display for easy
reference.
Press the MODE and
FAN buttons at the
same time for 10
seconds to enter
Advanced Setup
screens.
Advanced Setup
MODE FAN
I
ON
Setup
Press
MODE
Continued
Page 10
Select Display operation:
1 = Single Setpoint
2 = Dual Setpoint
See Page 24
cooling setpoint will always be displayed. To
display the room temperature, press and hold
the MODE button for two seconds. The
degree icon will blink when the large number
is displaying room temperature and will
remain solid when displaying the heating or
cooling setpoint.
2
Setup
2
Note: When Single Setpoint
is selected, the heating or
Advanced Setup
Select fan coil system
type:
2 = 2-pipe fan coil
4 = 4-pipe fan coil
4
2
Step #4 only appears if step #3 = 2.
2-PIPE SYSTEM OPERATION
1= Heat only system
2= Cool only system
3= Heat/Cool Auto
changeover
4= Heat/Cool Aux Electric
heat, Lockout Electric Heat
when Hot Water is available
5= Heat/Cool total electric
heat, no Hot Water, only
Electric Heat.
Note: #3 & #4 require accessory
changeover sensor
4
3
Setup
Press
MODE
Press
MODE
Continued
I
4
Setup
Page 11
On
Off
See Page 20, Note #2
Select operation when
fan is in the Auto mode:
On = continuous low
speed fan
Off = only energize
during a heating or
cooling cycle.
5
AUTO
Press
MODE

Advanced Setup
On
Off
2
7
HEAT
Setup
Select backlight operation:
On - Light continuously
Off - Light for 8 seconds
after a button press
Press
MODE
Press
MODE
Press
MODE
Press
MODE
Continued
Setup
8
Step #7 will not appear if step #4 = 1 or 2.
Page 12
2
6
Setup
Adjust the deadband
for the 1st stage.
(1-6)
See Page 17
Adjust the minimum
difference between
cooling & heating
setpoints.
(0-6)
C
F
Setup
9
Select thermostat
operation in degrees
Fahrenheit or Celsius.
COOL
Advanced Setup
Select Dry Contact
Unoccupied operation:
Unoccupied Setpoints
Off
Press
MODE
Page 13
Off = when the Dry Contact is
closed, the thermostat will turn
off.
Unoccupied = when the
Dry Contact is closed,
the thermostat will con-
trol to the Unoccupied setpoints.
Dry Contact
NO = Normally Open
NC = Normally Closed
NO
NC
Setup
I I
See Page 18
Press
MODE
Setup
85
I2
55
unoccupied
Adjust the cooling
setpoint for unocc-
upied periods.
(35 - 99, OF )
unoccupied
Press
MODE
Continued
Select sensor operation:
On =
or duct sensor
Off = control to remote
room sensor
read only outside
On
Off
Setup
I0
OUTSIDE

Advanced Setup
On
Off
2
7
HEAT
Setup
Select backlight operation:
On - Light continuously
Off - Light for 8 seconds
after a button press
Press
MODE
Press
MODE
Press
MODE
Press
MODE
Continued
Setup
8
Step #7 will not appear if step #4 = 1 or 2.
Page 12
2
6
Setup
Adjust the deadband
for the 1st stage.
(1-6)
See Page 17
Adjust the minimum
difference between
cooling & heating
setpoints.
(0-6)
C
F
Setup
9
Select thermostat
operation in degrees
Fahrenheit or Celsius.
COOL
Advanced Setup
Select Dry Contact
Unoccupied operation:
Unoccupied Setpoints
Off
Press
MODE
Page 13
Off = when the Dry Contact is
closed, the thermostat will turn
off.
Unoccupied = when the
Dry Contact is closed,
the thermostat will con-
trol to the Unoccupied setpoints.
Dry Contact
NO = Normally Open
NC = Normally Closed
NO
NC
Setup
I I
See Page 18
Press
MODE
Setup
85
I2
55
unoccupied
Adjust the cooling
setpoint for unocc-
upied periods.
(35 - 99, OF )
unoccupied
Press
MODE
Continued
Select sensor operation:
On =
or duct sensor
Off = control to remote
room sensor
read only outside
On
Off
Setup
I0
OUTSIDE

After programming is complete, press the
MODE and FAN buttons at the same time
for two seconds to leave the Setup screens.
If no buttons are pressed, the display will
leave the setup screens after 30 seconds.
Advanced Setup
Page 14
unoccupied
Adjust the heating set-
point for Unoccupied
periods.
(OF, 35 - 99 )
Advanced Setup
On / Off
1 / 2
2 / 4
1 - 5
On / Off
1 - 6
0 - 6
On / Off
F / C
On / Off
NO / NC
Unoccupied /
Off
35 - 99 , OF
OF, 35 - 99
Display Blanking
Single or Dual Setpoint
2-or 4-Pipe System
2-Pipe System Operation
Fan Auto Operation
Deadband/Temp. Swing
1st Stage
Minimum Heat/Cool
Differential
Thermoglow Backlight
Fahrenheit or Celsius
Read Only Remote
Sensor?
Dry Contact Polarity
Dry Contact Operation
Unocc. Cool Setpoint
Unocc. Heat Setpoint
Step
#Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Advanced Setup Table
Range Factory
Default
On
2
4
1
Off
2
2
Off
F
Off
NO
Unoccupied
85
55
Page 15

After programming is complete, press the
MODE and FAN buttons at the same time
for two seconds to leave the Setup screens.
If no buttons are pressed, the display will
leave the setup screens after 30 seconds.
Advanced Setup
Page 14
unoccupied
Adjust the heating set-
point for Unoccupied
periods.
(OF, 35 - 99 )
Advanced Setup
On / Off
1 / 2
2 / 4
1 - 5
On / Off
1 - 6
0 - 6
On / Off
F / C
On / Off
NO / NC
Unoccupied /
Off
35 - 99 , OF
OF, 35 - 99
Display Blanking
Single or Dual Setpoint
2-or 4-Pipe System
2-Pipe System Operation
Fan Auto Operation
Deadband/Temp. Swing
1st Stage
Minimum Heat/Cool
Differential
Thermoglow Backlight
Fahrenheit or Celsius
Read Only Remote
Sensor?
Dry Contact Polarity
Dry Contact Operation
Unocc. Cool Setpoint
Unocc. Heat Setpoint
Step
#Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Advanced Setup Table
Range Factory
Default
On
2
4
1
Off
2
2
Off
F
Off
NO
Unoccupied
85
55
Page 15

Advanced Setup
On / Off
1 / 2
2 / 4
1 - 5
On / Off
1 - 6
0 - 6
On / Off
F / C
On / Off
NO / NC
Unoccupied /
Off
35 - 99 , OF
OF, 35 - 99
Display Blanking
Single or Dual Setpoint
2-or 4-Pipe System
2-Pipe System Operation
Fan Auto Operation
Deadband/Temp. Swing
1st Stage
Minimum Heat/Cool
Differential
Thermoglow Backlight
Fahrenheit or Celsius
Read Only Remote
Sensor?
Dry Contact Polarity
Dry Contact Operation
Unocc. Cool Setpoint
Unocc. Heat Setpoint
Step
#Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Advanced Setup Table
Range Factory
Default
On
2
4
1
Off
2
2
Off
F
Off
NO
Unoccupied
85
55
Page 15
About Advanced Features & Operation
Page 17
The above figure assumes the minimum on time for the
prior stage has been met to allow the next stage to turn
on, once the deadbands have been exceeded.
TEMPERATURE
DECREASE INCREASE
Cool
SP
Heat
SP
Med-
speed
fan
Med-
speed
fan
Heating Cooling
Lo-
speed
fan
Hi-
speed
fan
Lo-
speed
fan
Hi-
speed
fan
DEADBAND OPERATION - Controls one Heat and
one Cool stage with a three speed fan (see below).
The medium speed fan for heat or cool is turned on
when: The temperature spread from the setpoint is
equal to or greater than: the setpoint plus the 1st stage
deadband (step #6, page 12), plus the 2nd stage dead-
band. This 2nd stage deadband is fixed at one degree
and is not adjustable.
The low speed fan for heat or cool is turned on when:
The temperature spread from the setpoint is equal to
or greater than: the setpoint plus the 1st stage dead-
band (step #6, page 12). This 1st stage deadband is
adjustable from 1-6 degrees and the default is two
degrees.
The high speed fan for heat or cool is turned on when:
The temperature spread from the setpoint is equal to or
greater than: the setpoint plus the 1st stage deadband
(step #6, page 12), plus the 2nd stage deadband, plus
the 3rd stage deadband. This 3rd stage deadband is
fixed at one degree and is not adjustable.
DB 3
1
DB 2
1
DB 1
1-6
DB 1
1-6
DB 2
1
DB 3
1

Advanced Setup
On / Off
1 / 2
2 / 4
1 - 5
On / Off
1 - 6
0 - 6
On / Off
F / C
On / Off
NO / NC
Unoccupied /
Off
35 - 99 , OF
OF, 35 - 99
Display Blanking
Single or Dual Setpoint
2-or 4-Pipe System
2-Pipe System Operation
Fan Auto Operation
Deadband/Temp. Swing
1st Stage
Minimum Heat/Cool
Differential
Thermoglow Backlight
Fahrenheit or Celsius
Read Only Remote
Sensor?
Dry Contact Polarity
Dry Contact Operation
Unocc. Cool Setpoint
Unocc. Heat Setpoint
Step
#Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Advanced Setup Table
Range Factory
Default
On
2
4
1
Off
2
2
Off
F
Off
NO
Unoccupied
85
55
Page 15
About Advanced Features & Operation
Page 17
The above figure assumes the minimum on time for the
prior stage has been met to allow the next stage to turn
on, once the deadbands have been exceeded.
TEMPERATURE
DECREASE INCREASE
Cool
SP
Heat
SP
Med-
speed
fan
Med-
speed
fan
Heating Cooling
Lo-
speed
fan
Hi-
speed
fan
Lo-
speed
fan
Hi-
speed
fan
DEADBAND OPERATION - Controls one Heat and
one Cool stage with a three speed fan (see below).
The medium speed fan for heat or cool is turned on
when: The temperature spread from the setpoint is
equal to or greater than: the setpoint plus the 1st stage
deadband (step #6, page 12), plus the 2nd stage dead-
band. This 2nd stage deadband is fixed at one degree
and is not adjustable.
The low speed fan for heat or cool is turned on when:
The temperature spread from the setpoint is equal to
or greater than: the setpoint plus the 1st stage dead-
band (step #6, page 12). This 1st stage deadband is
adjustable from 1-6 degrees and the default is two
degrees.
The high speed fan for heat or cool is turned on when:
The temperature spread from the setpoint is equal to or
greater than: the setpoint plus the 1st stage deadband
(step #6, page 12), plus the 2nd stage deadband, plus
the 3rd stage deadband. This 3rd stage deadband is
fixed at one degree and is not adjustable.
DB 3
1
DB 2
1
DB 1
1-6
DB 1
1-6
DB 2
1
DB 3
1

About Advanced Features & Operation
DRY CONTACT SWITCH -
ternal device such as a Central Time Clock, Occup-
ancy Sensor, or a Telephone activated device to force
one or more thermostats into an Unoccupied mode
(steps #11 and 12, page 13).
This feature allows an ex-
When the CK1 and R terminals are shorted together,
and the thermostat is programmed for Unoccupied
operation (step #12, page 13), the thermostat will be
forced into Unoccupied setpoints and the Unoccupied
icon will appear on the display.
Connect wires to a time
clock or other device to
force the thermostat into
Occupied 1 or Unoccu-
pied.
Important Note: For control of multiple
thermostats by 1 source, refer to the
enclosed yellow document P/N 88-175
‘Potential Phasing Problems’ before
installation.
C
G
RY1W2W1
TERMINALCONNECTIONS
4Z95
24V. 60HZ
NEC CLASS 2
ENCLOSED
ENERGY
MANAGEMENT
EQUPIMENT
MODEL: 33CSSP2-FC
X072500204
MADE IN CHINA
Y2
RS
RS+5H2OCK1
Page 18
About Advanced Features & Operation
WARNING: This will reset all Advanced Program-
ming to the default settings. Any information
entered prior to this reset will be permanently
lost.
FACTORY DEFAULTS -
return all the stored settings back to the factory default
settings, follow the instructions below.
If, for any reason, you desire to
After all of the icons appear,
release the MODE and DOWN
buttons. Then press and hold the
FAN button for 5 seconds.
After the letters Fd appear on the
display (Factory Default), release
the FAN button. Press the MODE
button twice to return to normal
operation.
Page 19
Place the thermostat in the OFF
mode.
Press button.
While holding the MODE button,
press and hold the DOWN button
for 5 seconds. All icons will
appear on the display.
and hold the MODE
MODE
1
2
MODE
3
4
MODE
FAN
72
OFF
72
OFF
unoccupied
Setup
88
88
C OOL
H EAT
Override
Locked
AUTO
O UTSIDE