IEI Technology POCm-DOCKING-6BAY User manual

POCm-DOCKING-6BAY
Page I
User Manual
POCm-DOCKING-6BAY
MODEL:
6-Bay Smart Charging Docking Station
with Fast Charging Capability and 255W PSU
Rev. 1.00 - October 9, 2019
User Manual

POCm-DOCKING-6BAY
Page II
Revision
Date Version Changes
October 9, 2019 1.00 Initial release

POCm-DOCKING-6BAY
Page III
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
CONTACT INFORMATION
Manufactured by:
IEI Integration Corp.
Address: No. 29, Zongxing Rd., Xizhi Dist.,
New Taipei City 221, Taiwan
Phone: [phone]
Fax: [phone]
Web Site: www.ieiworld.com
Sales Email: [e-mail]

POCm-DOCKING-6BAY
Page IV
Manual Conventions
WARNING
Warnings appear where overlooked details may cause damage to the
equipment or result in personal injury. Warnings should be taken
seriously.
CAUTION
Cautionary messages should be heeded to help reduce the chance of
losing data or damaging the product.
NOTE
These messages inform the reader of essential but non-critical
information. These messages should be read carefully as any directions
or instructions contained therein can help avoid making mistakes.

POCm-DOCKING-6BAY
Page V
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 OVERVIEW.................................................................................................................. 2
1.2 FEATURES................................................................................................................... 2
1.3 FRONT SIDE................................................................................................................ 3
1.4 REAR SIDE ................................................................................................................. 4
1.5 SPECIFICATIONS ......................................................................................................... 4
1.6 DIMENSIONS............................................................................................................... 5
2 UNPACKING ................................................................................................................. 6
2.1 UNPACKING ................................................................................................................ 7
2.2 PACKING LIST............................................................................................................. 8
3 INSTALLATION ........................................................................................................... 9
3.1 SAFETY PRECAUTIONS ............................................................................................. 10
3.2 INSTALLATION PRECAUTIONS ....................................................................................11
3.3 CHARGING BATTERY .................................................................................................11
A REGULATORY COMPLIANCE .............................................................................. 13
B PRODUCT DISPOSAL .............................................................................................. 15
C MAINTENANCE AND CLEANING PRECAUTIONS .......................................... 17
C.1.1 Maintenance and Cleaning ............................................................................. 18
C.1.2 Cleaning Tools................................................................................................. 19
D SYMBOL DEFINITIONS .......................................................................................... 20
E HAZARDOUS MATERIALS DISCLOSURE ......................................................... 22

POCm-DOCKING-6BAY
Page VI
List of Figures
Figure 1-1: POCm-DOCKING-6BAY ..............................................................................................2
Figure 1-2: Front Side.....................................................................................................................3
Figure 1-3: Rear Side......................................................................................................................4
Figure 1-4: POCm-DOCKING-6BAY Dimensions (mm)...............................................................5
Figure 3-1: Battery Charging .......................................................................................................12

POCm-DOCKING-6BAY
Page VII
List of Tables
Table 1-1: LED Indicators ..............................................................................................................3
Table 1-2: Specifications ...............................................................................................................5

POCm-DOCKING-6BAY
Page 1
1 Introduction
Chapter
1

POCm-DOCKING-6BAY
Page 2
1.1 Overview
Figure 1-1: POCm-DOCKING-6BAY
The POCm-DOCKING-6BAY is a 6-bay docking station designed for charging the
batteries of the POCm-W22C/W24C-ULT3 series medical panel PC.
1.2 Features
The POCm-DOCKING-6BAY features are listed below:
Unique 6-bay design for battery charging
Fast charging: 3~3.5 hours from 0 to 100%
Nice and clean design ideal for medical application
Equipped with a 255 W power adapter
Built-in one active fan for thermal management

POCm-DOCKING-6BAY
Page 3
1.3 Front Side
The front side of the POCm-DOCKING-6BAY is shown below (Figure 1-2).
Figure 1-2: Front Side
The descriptions of each LED indicator are listed below.
Battery State LED Indicator Description
Good Battery
Charging: solid red
Fully charged: solid green
Weak Battery
(FCC < 50%)
Charging: blinking orange
Fully charged: solid orange
Error Blinking red
No Battery or Non-IEI Battery LED off
Table 1-1: LED Indicators

POCm-DOCKING-6BAY
Page 4
1.4 Rear Side
The rear side of the POCm-DOCKING-6BAY is shown below (Figure 1-3).
Figure 1-3: Rear Side
1.5 Specifications
The technical specifications for the POCm-DOCKING-6BAY are listed below.
POCm-DOCKING-6BAY
Battery Bay 6
Battery
TC-202 (7800mAh)
Maximum charge voltage: 12.6 V
Maximum charge current: 2.2 A/ bay
Battery Charge Time 3~3.5 hours from 0 to 100% (TC-202)
Power Supply
255 W power adapter
Vin=100 ~240 VAC, Vout=15 VDC
LED Indicators 1 x Power LED (orange)
6 x Battery LED (green/red)
Power Switch AT power switch
Power Connector 6-pin Molex power connector

POCm-DOCKING-6BAY
Page 5
Thermal
One active fan
- Without battery: 20% fan speed
- With battery: 55% fan speed
- Temperature ≥ 48°C: 70% fan speed
Color White
Operating Temperature
0°C ~40°C (32°F~104°F)
Storage Temperature -20°C ~60°C (-4°F~140°F)
Operating Humidity 20%~90%, non-condensing
Storage Humidity 10%~95%, non-condensing
Chassis Construction NCT metal housing
Table 1-2: Specifications
1.6 Dimensions
The POCm-DOCKING-6BAY dimensions are shown below.
Figure 1-4: POCm-DOCKING-6BAY Dimensions (mm)

POCm-DOCKING-6BAY
Page 6
2 Unpacking
Chapter
2

POCm-DOCKING-6BAY
Page 7
2.1 Unpacking
To unpack the docking station, follow the steps below:
Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
external (second) box.
Step 2: Open the external (second) box.
Step 3: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
internal (first) box.
Step 4: Lift the docking station out of the boxes.
Step 5: Remove both polystyrene ends, one from each side.
Step 6: Make sure all the components listed in the packing list are present. Step 0:

POCm-DOCKING-6BAY
Page 8
2.2 Packing List
NOTE:
If any of the components listed in the checklist below are missing, do not
proceed with the installation. Contact the IEI reseller or vendor the
POCm-DOCKING-6BAY
was purchased from or contact an IEI sales
representative directly by sending an email to [e-mail].
The POCm-DOCKING-6BAY docking station is shipped with the following components:
Quantity Item Image
1 POCm-DOCKING-6BAY battery charging
docking station
1 255 W power adapter
(P/N: 63040-030138-100-RS)
1 Power cord (EU)
(P/N: 32702-000200-100-RS)

POCm-DOCKING-6BAY
Page 9
3 Installation
Chapter
3

POCm-DOCKING-6BAY
Page 10
3.1 Safety Precautions
Please ensure the following safety precautions are adhered to at all times.
To prevent the risk of electric shock, make sure power cord is
unplugged from wall socket. To fully disengage the power to the unit,
please disconnect the power cord from the ac outlet. Refer servicing to
qualified service personnel. The AC outlet shall be readily available and
accessible.
Make sure the power is turned off and the power cord is disconnected
whenever the POCm-DOCKING-6BAY is being installed, moved or modified.
Do not apply voltage levels that exceed the specified voltage range.
Doing so may cause fire and/or an electrical shock. Use a power cord that
matches the voltage of the power outlet, which has been approved and
complies with the safety standard of your particular country.
DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°
C (-4°F) OR ABOVE 60° C (140° F). IT MAY DAMAGE THE EQUIPMENT.
Do not drop or insert any objects into the ventilation openings of the
POCm-DOCKING-6BAY.
If considerable amounts of dust, water, or fluids enter the
POCm-DOCKING-6BAY, turn off the power supply immediately, unplug the
power cord, and contact the POCm-DOCKING-6BAY vendor.
DO NOT:
oDrop the POCm-DOCKING-6BAY against a hard surface.
oIn a site where the ambient temperature exceeds the rated temperature

POCm-DOCKING-6BAY
Page 11
3.2 Installation Precautions
When installing the docking station, please follow the precautions listed below:
Manufacturer authorization: Do not modify this equipment without
authorization of manufacturer.
Certified Engineers: Only certified engineers should install and modify the
hardware settings.
Power turned off: When installing the POCm-DOCKING-6BAY, make sure
the power is off. Failing to turn off the power may cause severe injury to the
body and/or damage to the system.
3.3 Charging Battery
To charging the batteries of the POCm-W22C/W24C-ULT3 series system, follow the steps
below:
WARNING:
The POCm-DOCKING-6BAY docking station is designed to charge the
batteries of the POCm-W22C/W24C-ULT3 system. Do not insert other type
of battery into the slots of the POCm-DOCKING-6BAY. Doing so may cause
damage to the battery and the docking station.
Use only the power adapter approved for this device. Use of another type of
adapter may risk fire or explosion;
Do not apply voltage levels that exceed the specified voltage range. Doing
so may cause fire and/or an electrical shock. Use a power cord that
matches the voltage of the power outlet, which has been approved and
complies with the safety standard of your particular country.
Step 1: Connect the supplied power adapter to the power connector on the rear of the
docking station.
Step 2: Connect the supplied power cord to the power adapter. Plug the power cord into
any standard power outlet.

POCm-DOCKING-6BAY
Page 12
Step 3: Turn on the docking station by using the power switch on the rear panel. The
power LED on the front panel lights up in orange.
Step 4: Insert a battery into a battery bay as shown below. The LED indicator lights on in
red indicating the battery is being charged. The LED will turn to green when the
battery is fully charged.Step 0:
Figure 3-1: Battery Charging