IEI Technology IMBA-X9654 User manual

1
ATX Form Factor with Intel® Core 2 Quad/Duo, Pentium®
D/Pentium® 4, Celeron D CPU FSB 533/800/1066MHz,
VGA, Dual Channel DDR2, LPT, 6 x SATA II,8 x USB2.0 and
6 x COM
IMBA-X9654
Quick Installation Guide
Version 1.0
Aug. 31, 2007
Package Contents
IMBA-X9654 package includes the following items:
 1 x IMBA-X9654 industrial motherboard
 6 x SATA Cable
 3 x SATA Power Cable
 1 x Dual RS-232 Cable
 1 x RS-232 Cable
 1 x I/O Shielding
 10 x mini jumper pack
 1 x Utility CD
 1 x QIG (Quick Installation Guide)
©2006 Copyright by IEI Technology corp.
All rights reserved.

2
Specifications
 CPU: LGA 775 Intel® Core 2 Quad/Duo, Pentium® 4/D, Celeron D
processor, FSB 533/800/1066MHz
 System Chipset: Intel® Q965 + ICH8DO
 BIOS : AMI BIOS Label
 System memory:
4 x 240-pin Dual channel DDR2 533/667/800MHz up to 8GB
 Ethernet: Dual Broadcom BCM5787M for PCI express GbE (LAN1
with ASF2.0 remote control support)
 I/O Interface:
8 x USB 2.0
6 x SATA II
1 x LPT
5 x RS-232, 1 x RS-232/422/485
2 x 10-pin header for TPM modules support
2 x PS/2 for KB / MS
 Expansion
1 x PCIe x16
3 x PCIe x4
3 x PCI
 Digital I/O: 8 bit digital I/O, 4-bit input / 4-bit output
 IrDA: 1 x IrDA by pin header
 Super I/O: IT8712F
 Audio: Realtek ALC883 HD Audio codec
 Display: VGA integrated in Intel® Q965
 WDT: Software programmable 1-255 sec. By super I/O
 Power Supply: ATX support
 Power Consumption:
[email protected], [email protected], 3.3V@ 5.74A, [email protected]
(Pentium D 840 3.2GHz/800MHz CPU with 1GB DDR2 667MHz)
[email protected], [email protected], 3.3V@ 4.03A, [email protected]
(Core 2 Duo E6400 2.13GHz/1066MHz CPU with 1GB DDR2
667MHz)

3
 Temperature: Operation: 0 ~ 60°C (32 ~ 140°F)
 Humidity: Operation: 5% ~ 95% non-condensing
 Dimension: 305(L) mm x 244(W) mm
 Weight: GW: 1350g; NW: 750g
Ordering Information
IMBA-X9654-R10
ATX Motherboard with Intel® LGA 775, Core 2 Quad/Duo, Pentium® D/4,
Celeron® D processor FSB 533/800/1066MHz, PCIe GbE, SATA II and
Audio
CB-USB02-RS: Dual USB Cable
CB-USB14-RS: Four USB Cable
32200-000063-RS: RS-232/422/485 Cable
CF-520-RS: CPU Cooler
CF-775A-RS: CPU Cooler
TPM-SI01-R10: 20-pin SINOSUN TPM Module, S/W Management Tool
TPM-WI01-R10: 20-pin WINBOND TPM Module, S/W Management Tool
TPM-IN01-R10: 20-pin INFINEON TPM Module, S/W Management Tool
SDVO-100VGA-R10: PCIe x 16 VGA Output SDVO Card supports dual
display (IEI CPU board only)
SDVO-100DVI-R10: PCIe x 16 DVI Output SDVO Card supports dual
display (IEI CPU board only)
Jumpers setting and Connectors
JP2: Clear CMOS Setup
JP2 Description
Open Normal Operation
Short Clear CMOS Setup
JP3 : COM2 Mode Selection
PIN Description
1-2 RS-232
2-3 RS-422/RS-485

4
TPM1: TPM Connector
PIN Description PIN Description
1 Clock 2 GND
3 Frame 4 KEY
5 Reset 6 +5V
7 LAD3 8 LAD2
9 +3.3V 10 LAD1
11 LAD0 12 GND
13 SCL 14 SDA
15 +3.3V SBY 16 Serial IRQ
17 GND 18 NC
19 Power Down 20 DRQ
CN3: Front Panel Audio Connector (2.54mm)
PIN Description PIN Description
1 MIC (L) 2 GND
3 MIC (R) 4 +5V/ICH_GPI19
5 LINE OUT(R) 6 PULL DOWN
7 LINE OUT SENSE 8 KEY
9 LINE OUT(L) 10 PULL DOWN
F_PANEL1：Front Panel Connector
Function PIN Description Function PIN Description
2 BEEP_PWR 12 RESET
4 NC
RESET 14 GND
6 NC 11 IDE_LED+
BUZZER
8 PC_BEEP HDD LED 13 IDE_LED-
1 LED+ 7 POWER BUTTON-POWER
LED 5 LED-
POWER
BUTTON 9 POWER BUTTON+
CN4: SPI Flash Connector
PIN Description PIN Description
1 SPI VCC 2 GND
3 CS# 4 CLOCK
5 SO 6 SI
7 NC 8 NC
CN1: SPDIF Connector
PIN Description PIN Description
1 +5V 2 NC
3 SPDIF OUT 4 GND
5 SPDIF IN

5
COM3~6: Serial Port 2 x 5 Box Header Connector
PIN Description PIN Description
1 DCD 2 DSR
3 RXD 4 RTS
5 TXD 6 CTS
7 DTR 8 RI
9 GND 10 NC
COM2: Serial Port 2 x 7 Pin Header Connector
PIN Description PIN Description
1 DCD 2 DSR
3 RXD 4 RTS
5 TXD 6 CTS
7 DTR 8 RI
9 GND 10 NC
11 TX+ 12 TX-
13 RX+ 14 RX-
IO_FAN1, IO_FAN3 :
SYSTEM Fan Connector
PIN Description
1 GND
2 +12V
3 Rotation Signal
IO_FAN2 : CPU Fan
Connector
PIN Description
1 GND
2 +12V
3 Rotation Signal
4 Control
USB1, USB2: 8 PIN Header USB Connectors
PIN Description PIN Description
1 USB POWER 2 GND
3 DATA- 4 DATA+
5 DATA+ 6 DATA-
7 GND 8 USB POWER
IR1: IrDA Connector
PIN Description
1 +5V
2 NC
3 IR-RX
4 GND
5 IR-TX

6
Board Layout: Jumper and Connector Locations
DIO1: Digital Input / Output
PIN Description PIN Description
1 GND 2 +5V
3 Input0 4 Output0
5 Input1 6 Output1
7 Input2 8 Output2
9 Input3 10 Output3

7