IEI Technology WAFER-9102 User manual

1
3.5” SBC, Socket 479 with Intel® Pentium® M/ Celeron® M
processor with 400MHz FSB CPU, VGA/LVDS, PCIe GbE,
USB2.0, SATA and audio
WAFER-9102
Quick Installation Guide
Version 1.0
Oct. 01, 2008
Package Contents
WAFER-9102 package includes the following items:
z1 x WAFER-9102 Single Board Computer
z1 x Mini Jumper Pack
z2 x SATA Cable
z1 x KB/MS Cable
z1 x Audio Cable
z1 x Cooler (for WAFER-9102-R10, socket type only)
z1 x Utility CD
z1 x QIG (Quick Installation Guide)
©2006 Copyright by IEI Technology corp.
All rights reserved.

2
Specifications
zCPU:
Socket 479 Intel® Pentium® M/ Celeron® M processor with a
400 MHz FSB
On board Intel® Celeron® M 1GHz zero cache or 1GHz 512KB
cache processor
zSystem Chipset:
Intel® 910GMLE + ICH-6M
zBIOS
AMI Flash BIOS
zSystem Memory
One x 200-pin DDRII SDRAM SO-DIMM 400 MHz (system max.
2GB)
zEthernet: One Realtek RTL8111CP GbE chipsets
zI/O Interface
1 x RS-232
1 x RS-232/422/485
6 x USB 2.0 (2 by rear side, 4 by pin-header)
2 x SATA
1 x IDE
1 x LPT
1 x KB/MS (by 6-pin wafer-header)
zExpansion
1 x PCI-104 (PCI bus)
zDigital I/O: 8-bit digital I/O, 4-bit input/4-bit output
zIrDA: 1x Infrared Interface by super I/O
zSuper I/O: ITE IT8178F
zDisplay Interface:
Intel® Graphics Media Accelerator 900
VGA output Integrated in Intel® 910GMLE
18/24-bit dual channel LVDS
zAudio:
Realtek ALC655 with AC’97 codec by pin-header

3
zSSD: CF type II
zWDT: Software programmable 1-255 sec. system reset
zPower Supply: +12V/ +5V, AT/ATX Power
zPower Consumption:
5V@ 3.11A,12V@0.37A (Intel® Celeron® M 373 1.0G with 1GB
DDR2)
[email protected], 12V@1.57A (Intel® Pentium® M 725 1.6G with 1GB
DDR2)
zTemperature: 0 ~ 60°C (32 ~ 140°F)
zHumidity: Operating 5% ~ 95% non-condensing
zDimension: 146mm x 102mm
zWeight: GW: 700g; NW: 230g
Ordering Information
WAFER-9102-R10
3.5” SBC, Socket479 Intel® Pentium® M/ Celeron® M CPU with VGA/LVDS,
PCIe GbE, USB2.0, SATA and Audio
WAFER-9102-1GZ-R10
3.5” SBC with ULV Intel® Celeron® M 1GHz zero cache CPU with
VGA/LVDS, PCIe GbE, USB2.0, SATA and Audio
NOVA-9102-1GZ512-R10
3.5” SBC with ULV Intel® Celeron® M 1GHz 512KB cache CPU with
VGA/LVDS, PCIe GbE, USB2.0, SATA and Audio
32200-026500-RS: RS-232/422/485 cable
32000-070300-RS: Dual Port USB cable
32100-043403-RS: ATX Power Cable
32100-088600-RS: SATA Power Cable
32200-015100-RS: LPT cable
32200-000009-RS: 44pin 2.5” IDE Cable
32200-008800-RS: 44pin 2.5”/3.5” IDE Cable
Jumpers setting
LABEL FUNCTION
J_CMOS1 CMOS state setting
JP2 COM2 Port Mode setting
J_VLVDS1 LVDS1 Voltage Selection
JCF1 CF Card setting
JP3 PCI-104 VIO Voltage select
ATXCTL1 AT Power Mode Setting

4
J_CMOS1 : Clear CMOS Setup
J_CMOS1 DESCRIPTION
Short 1-2
(default)* Keep CMOS Setup (Normal Operation)
Short 2-3 Clear CMOS Setup
JP2 : configure COM2 Mode
JP1 DESCRIPTION
Short 1-2
(default) RS - 232
Short 3-4 RS - 422
Short 5-6 RS - 485
J_VLVDS1 : LVDS Voltage Selection
J_VLVDS1 DESCRIPTION
1-2 +3.3V LVDS
2-3 +5V LVDS
JCF1 : configure CF Card type
JCF1 DESCRIPTION
Open
(default) Slave
Short 1-2 Master
ATXCTL1 : AT Power Mode setting
ATXCTL1 DESCRIPTION
2-3
(default) AT Power Mode
Open ATX Power Mode
JP3: PCI-104
V
IO Voltage select
J2 DESCRIPTION
Short 1-2 VCC (+5V)
Short 2-3 VCC3 (+3.3V)

5
Connectors
LABEL FUNCTION
KB_MS1 Keyboard and Mouse Connector
CPU_FAN1 CPU Fan Connector
LAN1 RJ45 LAN Connector
FAN1 System Fan Connector
PWRBTN1 Power Button
ATXCTL1 ATX Power Control Connector
RESET1 Reset Button
IR1 Infrared Interface Connector
ATXPWR1 Power Source Connector
SATA1
SATA2 Serial ATA Connectors
VGA1 VGA 10-pin Connector
COM1 COM Port Connector
LED_C1 LED
Indicators +5V Power output
IDE1 IDE Connectors
LPT1 Parallel Port Connector
COM2 Internal Serial Port 14-pin Connectors
DIO1 Digital I/O Connector
LVDS1 LCD Panel LVDS Interface Connector
INVERTER1 LVDS1 Panel Backlight +12V Power Source
PC104_PLUS1 PC104 Plus Connector
CF1 Compact Flash Slot
USB01
USB23 Internal 4 Port USB Connectors
USB_C45 USB Port Connector
AUDIO1 AC’97 Connector
BAT1 Battery connector

6
KB_MS1: 6-pin Mini-DIN
Keyboard/Mouse Connector
PIN NO. DESCRIPTION
1 VCC (+5V)
2 Mouse Data
3 Mouse Clock
4 Keyboard Data
5 Keyboard Clock
6 GND
LAN1 : RJ45 LAN Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 MDIA3- 5 MDIA1+
2 MDIA3+ 6 MDIA2+-
3. MDIA2- 7 MDIA0-
4. MDIA1- 8 MDIA0+
CPU_FAN1 : CPU Fan Connector
PIN NO. DESCRIPTION
1 GND
2 +12V
3 CPUFANIN
4 CPUFANOUT
FAN1 : System Fan Connector
PIN NO. DESCRIPTION
1 SYSFANIN
2 VCC (+5V)
3 GND
A
TXCTL1 : ATX Power Control Connector
PIN NO. DESCRIPTION
1 5VSB
2 GND
3 PS_ON#
PWRBTN1 : Power Button
PIN NO. DESCRIPTION
1 PWRBTSW-
2 GND
RESET1 : Power Button
PIN NO. DESCRIPTION
1 PM_RESET
2 GND
IR1: Infrared Interface connector
PIN NO. DESCRIPTION
1 VCC (+5V)
2 NC
3 IR-RX
4 GND
5 IR-TX
A
TXPWR1 :
A
TX POWER IN
PIN NO. DESCRIPTION
1 +12V
2 GND
3 GND
4 VCC (+5V)

7
SATA1、SATA2 : Serial ATA Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 5 RX-
2 TX+ 6 RX+
3 TX- 7 GND
4 GND 8 N/C
VGA1 : 15-pin Female Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 RED 2 GREEN
3 BLUE 4 NC
5 GND 6 CRT_PLUG#
7 GND 8 GND
9 VCC 10 GND
11 NC 12 DDCDAT
13 HSYNC 14 VSYNC
15 DDCCLK
COM1 : Serial Port Connector
PIN NO. DESCRIPTION
1 DATA CARRIER DETECT (DCD#)
2 RECEIVEDATA (RXD)
3 TRANSMIT DATA (TXD)
4 DATA TERMINAL READY (DTR#)
5 GND
6 DATA SET READY (DSR#)
7 REQUEST TO SEND (RTS#)
8 CLEARTOSEND (CTS#)
9 RING INDICATOR (RI#)
LED_C1: 6-pin LED indicators
PIN NO. DESCRIPTION
1 VCC (+5V)+5V Power
Output 2 GND
3 VCC (+5V)
PWRLED 4 GND
5 VCC (+5V)
HDDLED 6 -HDLED

8
IDE1 : IDE Interface Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 RESET# 2 GND
3 DATA 7 4 DATA 8
5 DATA 6 6 DATA 9
7 DATA 5 8 DATA 10
9 DATA 4 10 DATA 11
11 DATA 3 12 DATA 12
13 DATA 2 14 DATA 13
15 DATA 1 16 DATA 14
17 DATA 0 18 DATA 15
19 GND 20 N/C
21 IDE DRQ 22 GND
23 IOW# 24 GND
25 IOR# 26 GND
27 IDE CHRDY 28 BALE – DEFAULT
29 IDE DACK 30 GND
31 INTERRUPT 32 N/C
33 SA1 34 PDIAG#
35 SA0 36 SA2
37 HDC CS0# 38 HDC CS1#
39 HDD ACTIVE# 40 GND
41 VCC (+5V) 42 VCC (+5V)
43 GND 44 N/C
LPT1 : Parallel Port Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 STROBE# 14 AUTO FORM FEED #
2 DATA0 15 ERROR#
3 DATA1 16 INITIALIZE#
4 DATA2 17 PRINTER SELECT LN#
5 DATA3 18 GND
6 DATA4 19 GND
7 DATA5 20 GND
8 DATA6 21 GND
9 DATA7 22 GND
10 ACKNOWLEDGE# 23 GND
11 BUSY 24 GND
12 PAPER EMPTY 25 GND
13 PRINTER SELECT 26 NC

9
COM2 : Internal Serial Port Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 DATA CARRIER DETECT
(DCD#) 2 DATA SET READY (DSR#)
3 RECEIVE DATA (RXD) 4 REQUEST TO SEND
(RTS#)
5 TRANSMIT DATA (TXD) 6 CLEAR TO SEND
(CTS#)
7 DATA TERMINAL READY
(DTR#) 8 RING INDICATOR (RI#)
9 GND 10 GND
11 TXD485+ 12 TXD485#
13 RXD485+ 14 RXD485#
DIO1 : Digital Input / Output Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 2 VCC (+5V)
3 Output 3 4 Output 2
5 Output 1 6 Output 0
7 Input 3 8 Input 2
9 Input 1 10 Input 0
LVDS1: LVDS Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND1 2 GND2
3 A_Y0 4 A_Y0#
5 A_Y1 6 A_Y1#
7 A_Y2 8 A_Y2#
9 A_CK 10 A_CK#
11 A_Y3 12 A_Y3#
13 GND3 14 GND4
15 B_Y0 16 B_Y0#
17 B_Y1 18 B_Y1#
19 B_Y2 20 B_Y2#
21 B_CK 22 B_CK#
23 B_Y3 24 B_Y3#
25 GND5 26 GND6
27 VCC_LCD 28 VCC_LCD
29 VCC_LCD 30 VCC_LCD

10
PC104_PLUS1: PC/104-Plus Connector (120-pin PCI bus)
PIN Description PIN Description PIN Description PIN Description
A1 GND B1 RESERVED1 C1 +5V D1 AD0
A2 VIO1 B2 AD2 C2 AD1 D2 +5V
A3 AD5 B3 GND C3 AD4 D3 AD3
A4 CBE0- B4 AD7 C4 GND D4 AD6
A5 GND B5 AD9 C5 AD8 D5 GND
A6 AD11 B6 VIO2 C6 AD10 D6 M66EN
A7 AD14 B7 AD13 C7 GND D7 AD12
A8 +3V B8 CBE1- C8 AD15 D8 +3V
A9 SERR- B9 GND C9 SBO- D9 PAR
A10 GND B10 PERR- C10 +3V D10 SDONE
A11 STOP- B11 +3V C11 LOCK- D11 GND
A12 +3V B12 TRDY- C12 GND D12 DEVSEL-
A13 FRAME- B13 GND C13 IRDY- D13 +3V
A14 GND B14 AD16 C14 +3V D14 CBE2-
A15 AD18 B15 +3V C15 AD17 D15 GND
A16 AD21 B16 AD20 C16 GND D16 AD19
A17 +3V B17 AD23 C17 AD22 D17 +3V
A18 IDSEL0 B18 GND C18 IDSEL1- D18 IDSEL2
A19 AD24 B19 CBE3- C19 VIO4 D19 IDSEL3
A20 GND B20 AD26 C20 AD25 D20 GND
A21 AD29 B21 +5V C21 AD28 D21 AD27
A22 +5V B22 AD30 C22 GND D22 AD31
A23 REQ0- B23 GND C23 REQ1- D23 VIO5
A24 GND B24 REQ2- C24 +5V D24 GNT0-
A25 GNT1- B25 VIO3 C25 GNT2- D25 GND
A26 +5V B26 PCICLK0 C26 GND D26 PCICLK1
A27 PCICLK2 B27 +5V C27 PCICLK3 D27 GND
A28 GND B28 INTD- C28 +5V D28 PCIRST-
A29 +12V B29 INTA- C29 INTB- D29 INTC-
A30 -12V B30 RESERVED2 C30 RESERVED3 D30 GND
INVERTER1 : 5-pin Header Inverter Connector
PIN NO. DESCRIPTION
1 LCD_BKLTCTL
2 GND
3 +12V
4 GND
5 BACKLIGHT ENABLE

11
CF1 : CF Card Interface Slot
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 26 CD1#
2 D3 27 D11
3 D4 28 D12
4 D5 29 D13
5 D6 30 D14
6 D7 31 D15
7 CE# 32 CE2#
8 A10 33 VS1#
9 OE# 34 IOR#
10 A9 35 IOW#
11 A8 36 WE#
12 A7 37 IRQ
13 VCC 38 VCC
14 A6 39 CSEL#
15 A5 40 VS2#
16 A4 41 RESET#
17 A3 42 WAIT#
18 A2 43 INPACK#
19 A1 44 REG#
20 A0 45 BVD2
21 D0 46 BVD1
22 D1 47 D8
23 D2 48 D9
24 IOCS16# 49 D10
25 CD2# 50 GND2

12
USB01 & USB23 : Internal USB Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VCC (+5V) 2 GND
3 DATA- 4 DATA+
5 DATA+ 6 DATA-
7 GND 8 VCC (+5V)
USB_C45: External USB Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VCC (+5V) 5 VCC (+5V)
2 DATA- 6 DATA-
3 DATA+ 7 DATA+
4 GND 8 GND
AUDIO1: AC’97 Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 LINE_OUTR 2 LINEIN_R
3 GND_AUDIO 4 GND_AUDIO
5 LINE_OUTL 6 LINEIN_L
7 GND_AUDIO 8 GND_AUDIO
9 MICIN 10 MICIN
BAT1 : +3V Battery Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 BAT (+3V) 2 GND

13
Board Layout: Jumper and Connector Locations
LAN1

14