Uplift Desk CHR456 User manual

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
Step 3
Insert the Casters into the holes on the Base, and press them rmly into
the slots to secure them in place.
Flip the Base, Casters down, onto the oor and insert the Cylinder into the Base.
Keep the Cylinder away from you to prevent you from getting oil on you
or on your clothes.
Step 4
Lower the chair assembly onto the Cylinder to secure it in place.
Package Contents
®
J3 ™ Ergonomic Chair
CHR456
Allen wrench (handle)
Allen wrench (L-shape)
Screw cover
Base
Casters
(qty 5)
Arm screw (qty 6)
Back screw (qty 3)
Headrest screw (qty 2)
Cylinder Arms Back Seat
Headrest
Step 5
Attach the Headrest to the Back using two (2) Headrest screws and the
L-shape Allen wrench.
Note: If you are having difculty aligning the Headrest and Back screw holes,
it may help to tilt the chair forward. Lean it on a table or roll up a towel under
the Arms to prop the chair forward, to more easily line up the holes on the
Headrest with the holes on the chair’s Back.
Once screwed in, place the Screw cover in the spot located at the top of the
chair, covering the screws.
Step 1
Place the Seat upside down on the edge of a stable surface like a desk or a
table. Slide the Back in place and line up the holes for the Back and the Seat.
Have a friend help keep it steady while you attach the Back to the Seat and
screw into place using three (3) Back screws and the Allen wrench.
Note: When inserting the screws, tighten for only a few turns each. Allow
there to be some give as you insert each screw into place. Once all three
screws are threaded, tighten them all.
CHR456/R02
Step 2
Take your chair assembly off the table and set it on the oor, turning it on its side.
Insert an Arm into the Seat and screw into place using three (3) Arm screws
and the Allen wrench.
Flip chair assembly onto the other side and repeat for the other Arm.

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
Seat Height
To adjust the height of your seat higher or lower, squeeze the latch located
underneath the seat. Sit on the seat to lower it and stand up to allow the seat to rise.
Seat Depth
To adjust the depth of your seat, engage the tab located under the seat and slide the
seat to your preferred position.
Adjustment Guide
Back Tilt Adjustment
When the latch is UP, the back is locked. When it’s pushed back, the back is unlocked.
This allows the back to “free oat” and recline to any position you wish within the chair’s
22 degrees of recline.
If you prefer the back to be stationary, there are 4 preset locking positions in this mode.
Simply recline the back to the desired position and ip the latch UP to lock into the
nearest forward position. To unlock the back again or to change positions, ip the switch
back and press back slightly to disengage the lock.
Headrest Height
Hold the headrest rmly to lift or lower it to your desired height.
Headrest Tilt
Hold the headrest rmly and adjust it at an upward or downward angle to the posi-
tion where it’s most comfortable.
Back Height
Hold the back rmly to lift or lower the back height to your desired height. There are
4 locking positions, with a height range of 2.4’’ (.6’’ per position).
Arm Height
Press the button on each arm to unlock them, and move the armrests up and down.
There are 6 locking positions, with a height range of 2.8’’ (.6’’ per position).
Copyright Notice: These instructions are a component of the UPLIFT J3™ Ergonomic Chair. These instructions are part of the scope of delivery, even if the item is resold. These instructions are also available
on the UPLIFT Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior written consent of UPLIFT Desk.
These instructions are subject to United States copyright law.
©
!CAUTION: Read all instructions before assembly. Failure to assemble properly may
result in product damage or injury.