iFox EC1270 Assembly instructions

Thank you for choosing the iFox CDMA 311A USB Slider
Modem. With your USB Slider, you can access a wireless
network at high speed.
Note:
This manual describes the appearance of the USB Slider, as well as the procedures for
preparation, installation, and removal. For operation details about the management
program, see the online help included in the management program.
Getting to Know Your iFox CDMA 311A USB Slider Modem
The following figure shows the appearance of the USB Slider. It is provided only for your
reference. The actual product may be different.
1

1
3
4
5
2
nUSB Connector
It connects the USB Slider to a PC.
oSlider
It extends or retracts the USB connector.
pIndicator
It indicates the status of the USB Slider.
2

3
zSolid: The USB Slider is powered on.
zBlinking once every 2s: The USB Slider is searching for a network or no network is
found.
zBlinking twice every 2s: The USB Slider finds a network.
zBlinking once every 0.2s: The USB Slider is transmitting data.
qUIM Card Slot
It holds a User Identity Module (UIM) card.
rMicroSD Card Slot
It holds a microSD card.
Getting Your iFox CDMA 311A USB Slider Modem Ready
Installing the UIM and mircoSD Card
1. Slide the back cover to remove it from the USB Slider.
2. Insert the UIM card and the microSD card into the corresponding card slots, as shown in

the following figure.
3. Replace the back cover and slide it into place.
Note:
zThe microSD card is an optional accessory. If it is not provided in the package, you can
buy one yourself.
zEnsure that the beveled edge of the UIM card is properly aligned with that of the UIM
card slot and the microSD card is inserted according to the direction as labeled on the
microSD card slot.
zDo not remove the microSD or UIM card when the card is in use. Otherwise, the card as
4

well as your USB Slider may get damaged and the data stored on the card may be
corrupted.
Preparing Your Front Cover
1. Open the front cover of the USB Slider by lifting the cover at the point indicated by the
arrow in the left diagram below.
2. Insert your favourite front cover into the slots at the edge of the USB Slider as shown
below. Press the front cover until it clicks into place.
5

Installation/Removal Guide
The procedure for installing the management program depends on the operating system
(OS) installed on your PC. The following sections take Windows XP as an example.
Connecting the USB Slider to a PC
Push the slider on the side of the USB Slider to fully extend the USB connector. Then plug
the USB Slider into the USB port of your PC.
6

7
Installing the USB Slider Management Program
1. Connect the USB Slider with the PC.
2. The OS automatically detects and recognizes the new hardware and starts the
installation wizard.
Note:
If the auto-run program does not respond, find the AutoRun.exe file in the driver path.
Then double-click AutoRun.exe to run the program.
3. Follow the on-screen instructions of the installation wizard.
4. After the program is installed, a shortcut icon for the management program appears on
the desktop.
Starting the Management Program
After being installed, the management program starts automatically. Then every time the
USB Slider is connected to the PC, the management program starts automatically.
You can also double-click the shortcut icon on the desktop to start the management
program.

Removing the USB Slider
1. Double-click in the notification area. Then the Unplug or Eject Hardware dialog
box appears.
2. Select the corresponding hardware and then click Stop.
3. When the message "It is safe to remove the device" appears, remove the USB Slider.
Uninstalling the Management Program
1. Choose Start > Control Panel > Add or Remove Programs.
2. Find the management program and click Remove to uninstall the management
program.
Note:
Exit the management program before uninstalling it.
Version: V100R001_01 Part Number: 31010EUR
8