iGen SAR-100 User manual

User Manual
1
Installation Instruction for Smart Anti-rejection Box
Model: SAR-100

User Manual
2
Contents
ⅠIntroduction ......................................................................................................................... 3
ⅡParameters ...........................................................................................................................3
ⅢProduct Installation ............................................................................................................. 4
3.1 Tool ............................................................................................................................... 4
3.2 Location ........................................................................................................................4
3.3 Notice ............................................................................................................................4
ⅣAnti-rejection System Diagram ........................................................................................... 5
ⅤDevice Installation ................................................................................................................6
5.1 Installation ....................................................................................................................6
5.2 Device wiring ................................................................................................................6
ⅥNetworking Configuration .................................................................................................. 8
6.1 WiFi Access ..................................................................................................................8
6.2 Ethernet Access ...................................................................................................... 16
Ⅶ............................................................................................................................................. 20
7.1 Anti-rejection setup .................................................................................................20
ⅧInstruction for Indicator Light, Dial Switch and Reset Button ...................................... 23
8.1 Indicator Light ............................................................................................................23
8.2 Dial Switch ..................................................................................................................23
8.3 Reset Button .............................................................................................................. 24
Ⅸ............................................................................................................................................. 24
9.1 Register and create a plant ....................................................................................... 24
9.2 SOLARMAN Smart APP .............................................................................................25
9.3 SOLARMAN Business APP .......................................................................................29
ⅩContact ............................................................................................................................... 32

User Manual
3
ⅠIntroduction
SOLARMAN anti-rejection box enables the real-time monitoring of grid-tied situation through the integration of
three-phase meter, logger and CT, which meets the requirement of real-time adjusting inverter output power at power
consumption scenario. It can connect to many inverters and support data transmission via WiFi&Ethernet.
ⅡParameters
Parameter
Product Model
SAR-100
Remote Communication
2.4G WiFi+Ethernet
Local Communication
RS 485
No. of Connections
5/10 Select according to the number of parallel machines
Accessing Method
Three-Phase Four-Wire
Working Voltage
3x230/400V 50/60Hz
Working Current
3x1.5(6)A
CT (Regular)
250/5A, 600/5A, 800/5A, 1000/5A, 1500/5A, 2000/5A
IP Grade
IP65
Working Temperature
-25℃~+60℃
Working Humidity
5%-95% (No Condensation)
Installation Method
Wall-Hanging
Size
~400*300*170mm
Weight
~3.3kg

User Manual
4
ⅢProduct Installation
3.1 Tool
Table 3.1 Preparation Tool
Tool Name
Picture
Usage
Note
Wire stripper
Strip cable insulation
Cross screwdriver
Use to connect
Cable
Connect logger with router
Shielded twisted pair
Expansion Screw
Use to install anti-rejection
Box
Specification: M6*60
Adjustable Wrench
Use to fix expansion screws
Percussion Drill
Use to drill holes
Computer with network
port
Use to operate network
configuration
COM Line
RS485Communication
(Shielded twisted
pair)
Diameter: 3-7mm
Voltage-sampling cable
Use to connect voltage
sampling signal
Specification:AWG
12-18, 105°/600V
Double-core cable
Use to connect CT signal
Specification:AWG
16-22, 105°/600V
3.2 Location
The installation location must meet the following requirements.
3.2.1 The logger should be installed in doors, avoiding damp and dust environment. Direct sunlight and aggressive
vapour should also be avoided.
3.2.2 Environment temperature: -25℃～+60℃.
3.2.3 Max. communication distance for RS485 should be less than 500m.
Away from other wiring routes or pipes in doors, such as gas pipe, water pipe, electric wire and etc.
3.2.4 Away from metal structure to ensure wireless signal strength.
3.3 Notice
3.3.1 Power off the device before installation.
3.3.2 Double check the connection before power on the device.

User Manual
5
ⅣAnti-rejection System Diagram
If 485 link communication is not successful for some inverters, please connect a 120Ωresistance with repeater and A&B
point of the last inverter.

User Manual
6
ⅤDevice Installation
5.1 Installation
1.Select a right (firm&flat) place to install the device
2. Determine the drilling hole positions according to hangers (Refer to Fig. 5.1)
3. Fix the device using expansion screws
Fig. 5.1 Installation Diagram (Unit: mm)
5.2 Device wiring

User Manual
7
Double check the wiring and power on the device
Notice
1. Connect inverter output to the grid. Connect to phase line R ,S, T, N accordingly.
2. Connect voltage-sampling signal line, communication distance should be less than
100m. Connect to phase line R ,S, T, N accordingly.
3. Connect CT, communication distance should be less than 100m. CT direction
should be from grid to load and make sure R-phase CT connect to CT1-1/2, S-phase
CT connect to CT2-1/2, T-phase CT connect to CT3-1/2.
[Phase sequence of CT should be consistent with the phase sequence of
voltage-sampling signal. ±1/2 cannot be reversed. (Select current sensor according
to the device capacity.)]
4. RS485A-B cannot be reversed.
5. All devices can connect to ground line.
Inverter address settings
1.Meter address: 1
2.For one inverter, inverter address: 2
3.For multiple inverters, inverter address: 2, 3, 4, 5……
Tip: Address cannot be the same.
4.There's no need to set anti-reflux function: ON.
Notice: Please make sure local anti-reflux function: OFF.

User Manual
8
ⅥNetworking Configuration
6.1 WiFi Access
Go to DIN-Rail logger configuration page
Step 1 Prepare a computer/smart phone that can connect to wireless network
Step 2 Connect to logger AP (Please do Not connect the cable when configuring the logger)
Select and connect AP XXXXXXXXX in the network list (XXXXXXXXX means logger SN)
Step 3 Log in to logger WEB page
Open a browser and enter 10.10.100.254.
Username: admin
Password: admin
Notice：
1. DIN-Rail logger supports WiFi&Ethernet access. Please select one method to
access according to actual situation.
Notice：
Supported browser: IE 8+, Chrome 15+、Firefox 10+

User Manual
9
Step 4 During the first login, the browser will remind you whether to save the password. You can decide according to your
usage habit.
Step 5 During the first login, the system will prompt that the AP is not encrypted. Click OK to encrypt it, click Cancel if not.
Step 6 If you choose to encrypt AP, you will go to “AP Encryption Modification”, enter your password and click Save.
Example: choose WPA2-PSK as encryption mode, AES as encryption algorithm, password: 1234578 (Please remember the
password.)
Users can select encryption mode according to actual situation. After AP has been encrypted, it requires to connect AP
again.
(If you forget your password or want to cancel the encryption, please long press Reset button for 4s to reset which will got
to reconfiguration process. AP password, network information and anti-rejection settings will restore factory settings at
this time.)

User Manual
10
Step 7 Click Reboot after saving.
After AP encryption has been set, you will be reminded again during network settings.
If the following prompt shows, you can select "AP encryption modification" accordingly.
Step 8 Refresh the WEB page and log in again.
Username: admin
Password: admin