Iget SECURITY M4 User manual

iGET SECURITY M4
Smart Alarm System
User Manual EN
Uživatelský Manuál CZ
Užívateľský Manuál SK
Használati Útmutató HU
Instrukcja Obsługi PL

1
CZ
SK
EN
PL
HU
P2
P2
P3
P3
P4
P5
P9
P11
P17
P18
P19
●Introduction
●Important Notes for Users
●About Safety
●Requirementsts
●System Status & User Authorities
●The Outlook
●Q&A
●Operating by App
●FAQ
●Specifications
●Safety Precautions
Table of Contents

2
CZ
SK
EN
PL
HU
Introduction
• Thank you for purchasing the Smart Alarm System. M4 will give you a complete control over your home's security and home automation
via your smartphone, tablets or web clients. This manual will guide you through the setup procedures
• The system could be operated via smartphones, tablets or web clients.
• Please note that all contents listed here might be slightly different from the contents of the package or in App.
Please check www.iget.eu to obtain the latest version of the user manual.
• Version: V1.0 EU-ENG
Important Notes for Users
• Please connect the power cable before first using.
• All sensors and devices in the package have already been paired with the main box before shipping. Users can start using the whole system
after setting the network. For the extra accessories (like sensors or smart devices), you need to pair them with the system for working normally.
• We make this system easy to set and use. Most users can finish all process within 15 minutes.
If there is any problem with the setting, please stop and contact the distributor for help.
• All manuals, warranty cards, nameplates and stickers with QR codes or barcodes, should be carefully kept for further use.

3
CZ
SK
EN
PL
HU
About Safety
• This system does not offer any guarantee of protection against burglary, robbery, theft, or any type of emergency. It is a DIY product and does
not come with a traditional monitoring service. However, most of the risks have been considered in our design to make your home safer.
• The users should continue to act prudently to protect the security of their lives and property. Any alarm system is subject to
compromise or failure for a variety of reasons as follows:
- An intruder may gain access through unprotected openings.
- An intruder may have the technical sophistication to bypass a sensor or the whole system.
- Signals sent by the main box or sensors may be blocked or reflected before being received, and a block can occur if
metal objects are moved into the path of the signal.
- Motion sensors can only detect the intrusion within the specified ranges and unobstructed areas.
- Malfunction of routers, limited services by wireless phone carriers or internet service providers, limited service such as
text messages or push notification provided by smartphone makers.
- Component failures or some other errors happen in the electrical system.
Requirements
• Wired/Wireless Router compatible with Wi-Fi IEEE 802.11 b/g/n standard.
• Internet Service Provider
• Mobile Telephone SIM card (only GSM/WCDMA/LTE SIM card, not CDMA one)
• iPhone or Android smartphone
• iOS version 7.0 or higher
• Android version 4.3 or higher.

4
CZ
SK
EN
PL
HU
System Status & User Authorities
• The M4 system does not support any wired sensors. The main box communicates with all sensors via wireless RF signal protocols.
• Most of the sensors have low battery warning mechanism. Users would receive notifications before the battery runs out.
• The system can change its security status according to the commands given by users or the signals sent from the triggered sensors.
- ARM:
All working sensors can be
triggered. The system will
gen- erate an alarm when
receiving the trigger signal
sent from sensors.
- DISARM:
This mode will de-activate
all sensors. This mode
will also turn off the siren
and stop the alarm process.
- HOME ARM:
This mode will allow some
selected sensors to keep
working while others are deac-
tivated. These sensors could
be selectedinApp.
- SOS:
This mode will trigger builtin
siren and send alarm messages
to emergency contacts. It also
triggers external sirens or other
sensors like smart.
- Life-related sensors like Smoke Detector or CO/GAS sensor will keep working all the time.
• There are three levels of user authorities.
- ADMINISTRATOR:
Who can fully control the system
and invite other users with
assigned levels.
- USER:
Who can operate
ARM/DISARM/HOME ARM/SOS
and control the smart plugs and
cameras, also can invite other
people as USER or GUEST.
- GUEST:
Who can only operate
ARM / DISARM / HOME ARM / SOS.

5
CZ
SK
EN
PL
HU
5V2A Power
RJ45 100M SIM
Louver
LED Indicator
STATUS LED MEANING
Normal Status Light ON ARM/DISARM/HOME ARM/SOS Etc.
Setting Status Fast Blinking
Networking Configure
Reseting
Updating
Errors Slow Blinking
Low Battery
Networking Errors
Other Errors
The Outlook
• Front View • Top View

6
CZ
SK
EN
PL
HU
Wall Mounting
Siren Hole
Battery Cover
Networking Configure
Power Switch
System Reset
• Back View

7
CZ
SK
EN
PL
HU
Step1. Download App "iGET M4"
2 ways to get "iGET M4" App:
- Search ”iGET M4“ on App Store or Google Play, download it directly.
- Scan the QR-code on the right with your smartphone, you can access download link directly.
- Please switch on power button at the back panel. You will hear ”beep”when indicator
at front panel start blinking, it will take around 45 seconds after powered on.
Step 2. PowerOn.
Step 3. Connect to your M4 alarm panel
- Please make sure you can access internet from your smart phone.
- Go to WiFi setting on your smart phone, then select the AP starting with iget_xxxx,
and the password is 1234567890.

8
CZ
SK
EN
PL
HU
Step 4. Network conguration
Step 5. Setting the password and name it.
Click "iGET M4" on your smart phone, then add the device by following the guidelines:
Click the App, press"Start
to add adevice"
You will get a "Succeed
page" after indicator of Then set a password for the Name it. Now it is.
Select LAN or WiFi for con-
necting panel to internet.
Key in the password for selectedWifi
*The panel only supports 2.4G Wifi.
Confirm DHCP if connect to router by LAN
* Or config IP address manually
The panel will start to connect
internet after CONFIRM, It will
take around 45 seconds.