Ikegami ULE-185U User manual

Installation and User's Guide
All contents of this document may change without prior notice, and actual product appearance may differ from that depicted herein
BROADCAST/SURVEILLANCE APPLICATIONS
ULE-185U REV.F

Installation and User's Guide
2
<TABLE OF CONTENTS>
1 SAFETY INSTRUCTION 3
2 FCC RF INTERFERENCE STATEMENT 7
3 INSTALLATION 8
4 OSD MENU SETTING 12
5 FEATURE 18
6 TROUBLESHOOTING 19

Installation and User's Guide
3
•Follow this safety instruction to use the monitor properly and prevent the damage.
•Keep this user’s guide book for later use.
1. SAFETY INSTRUCTION
* This safety instruction has “Warning” & “Caution” as below
Warning - If the user does not follow this instruction,
it may cause the serious damage to the user.
Caution - If the user does not follow this instruction, it may cause the slight
damage to the user or cause some damages to the monitor.
Warning
Never remove the back cover and touch
the inside of the monitor.
If you need a service, please contact the
service center.
Keep away the monitor from the
direct sunlight and a heating appliance.
Never put objects of any kind into this
product as they may result in a risk of fire
or electric shock.
Connect the power cord to the wall
outlet tightly. If the power cord or plug are
defective and the wall outlet is not
tight, please do not use them.

Installation and User's Guide
4
Warning
Do not install this monitor on the outside
and near water. It may cause damage to
the product, electric shock and fire.
When lightning and thundering, unplug
the monitor from the wall outlet and
never touch it.
Unplug this product from the wall outlet,
when it does not operate for a long time.
When smoking and noising from the
monitor, unplug the product from the wall
outlet and contact a service center.
WARNING: How to fix
Do not open this product as it contains high voltage inside.
It may create an electric shock.
If the user disassembles and remove the back cover, it does not make sure
to make up for the damage and do a service and exchange the monitor.
For cleaning do not use liquid cleaners.
Never touch the power plug with wet-
hands.

Installation and User's Guide
5
Cautions
Install this monitor some distance
from the wall and do not install unless
proper ventilation is provided.
Place this product on a stable place.
If not, it may fall, causing serious
damages to the monitor and people.
The openings must not be blocked by
curtain, rug or other similar surface.
Before carrying the monitor, turn it off and
unplug the signal cables and the power
cord from the wall outlet.
When carrying this monitor, be careful
not to damage the panel and drop it
It may cause some trouble.
Take the power plug out from the wall
outlet.
Do not pull the cable. It may snap the
inner-wires and cause overheating and fire.

Installation and User's Guide
6
Cautions
Install this monitor about 50cm far from
the eyes and an angle of 0~15 degrees
below eyes. Too close installation may
cause having weak sight.
Do not press the LCD panel with hands or
the sharpened material hardly.
For cleaning, unplug the monitor from the
wall outlet. Do net use the liquid cloth.
Use the soft cloth.
Do not use the chemical liquid for cleaning.
It may cause fading and breakage.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR WATER.
Instructions for Disposal of Electrical and Electronic Equipment in Private Households
Disposal of used Electrical and Electronic Equipment
(Applicable in the European Union and other European countries with garbage separate
disposal and collection methods)
This symbol on the product, or in the related documents in the package, indicates that this
product shall not be treated as normal household waste. Instead, it should be taken to a proper
applicable collection point or depot for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent possible negative consequences for
the environment and human health, which could otherwise be caused by inappropriate waste handling of
this product. The recycling of materials will help to conserve natural resources.
For more detailed information about recycling of this product, please contact your local city authority,
your household waste disposal service or the place where you purchased the product.

Installation and User's Guide
7
NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio, TV technician for help.
- Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or
manufacturer could void the users authority to operate such equipment.
DOC COMPLIANCE NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out
in the radio interference regulation of Canadian Department of communications.
2. FCC RF INTERFERENCE STATEMENT

3. INSTALLATION
User Manual
Adapter
Trigger Cable
LCD Monitor
Remote Controller
Power Cable
Battery
3-1 Parts
VGA Cable
Installation and User's Guide
8

3-2 How to Install
1) KEY BUTTON
SHORT KEY FUNCTION
OSD Key Function
MENU Activate the menu function / Exit from the menu
SOURCE / ▼Input source menu / Source selection(move down from OSD menu)
AUTO / ▲Auto-fit screen with PC-RGB input / move up from OSD menu
◀(VOL) Decrease the level of volume and move the previous menu
(VOL)▶Increase the level of volume and select the OSD menu
Power On / Off
LED
Red : Power Off state
Green : Power On and available input signal state
Orange : When DPMS "ON" state, no input signal
▲+◀Press “▲ , ◀” Key 10 seconds simultaneously to lock /
unlock OSD Key
Installation and User's Guide
9

① ② ③ ④ ⑤ ⑥
⑦
⑧
⑨
⑩
⑪
①DC 12V DC adapter input
②AUDIO(VIDEO-1) Stereo audio input for VIDEO-1
③AUDIO(VIDEO-2) Stereo audio input for VIDEO-2
④VIDEO-1 IN/OUT VIDEO-1 signal input/output
⑤VIDEO-2 IN/OUT VIDEO-2 signal input/output
⑥TRIGGER TRIGGER signal input
⑦HDMI HDMI signal input
⑧VGA VGA(PC RGB) signal input
⑨AUDIO(PC) Stereo audio input for VGA
⑩For FW Update
⑪SDI IN/OUT SDI signal input/looping out
2) CONNECTION
Installation and User's Guide
10

3) REMOTE CONTROLLER
MODE SELECT MENU
VIDEO1 Select VIDEO1 mode
VIDEO2 Select VIDEO2 mode
HDMI Select HDMI mode
VGA (RGB) Select VGA mode
S.SET Select Input source
OSD CONTROL MENU
POWER Turn ON / OFF the monitor
MUTE Turn ON / OFF the sound
AUTO Auto adjust position of the screen (in VGA mode)
COLOR
TEMPERATURE Select color temperature of the screen
SCAN MODE Select the scan mode of the screen
VOL- / VOL+ Increase / Decrease the volume level
MENU / EXIT Activate and exit the OSD menu
KEY LOCK Locking the button (Prevent operation)
Installation and User's Guide
11

4. OSD MENU SETTING
MENU STRUCTURE
When user presses the menu key, the first “PICTURE” menu is displayed. Select by "◀"
key then two types of menu functions are shown as below.
- PICTURE : Menu related to PICTURE Function
- OPTION : Other OSD Menu Status Control and Firmware Update
If press "▲, ▼" key, then select sub title in functions.
The PICTURE Menu can be selected from the following 7 modes by pressing the ▲or ▼key.
PICTURE MENU
Picture Mode Adjust setting of the picture
Color Temperature Change color according to the color temperature
Aspect Ratio Change the aspect ratio
Noise Reduction Adjust noise attenuation of input signal
Screen Adjust the PC-RGB input signal to fit the screen
Trigger Select Trigger input
Pixel shift Select auto pixel shift
Installation and User's Guide
12

1) Picture Mode
Picture Mode can select 4 modes as Mild, Dynamic, Standard and User as shown in the figure
below. Press the "◀, ▶" key to change the mode.
Three of the four modes except for User mode are shipped with fixed values at the time of
shipment from the factory.
User mode can be set with “◀, ▶” keys by selecting each item below with “▲, ▼” key only
in the User mode.
2) Color Temperature
Color Temperature can select 4 modes as Cool, Medium, Warm and User as shown in the figure
below.
Three modes except User mode are factory shipped with factory default values, and
each color item (RED, GREEN, BLUE) is selected with the "▲, ▼" keys in the User mode only.
User settings are available.
Contrast Adjust difference in the color and brightness
Brightness Adjust the dark and light
Color Adjust for desired color intensity
Sharpness Adjust for best clarity of outline detail
Tint Adjust for natural flesh tones
Installation and User's Guide
13

3) Aspect Ratio
Aspect Ratio allows user to select the each aspect ratio as shown in the figure below.
(However, activated list is according to the input port and the input resolution.)
4) Noise Reduction
Noise Reduction can select 5 modes as Off, Low, Middle, High, Default as shown in the figure below.
5) Screen
Screen enables to set the active area of the display when using PC-RGB input port.
Auto Adjust is an item to be set automatically, and the input signal should be operated in the
signal state where the Outline has a lot of white color.
Installation and User's Guide
14

6) Trigger
Select Trigger input (Off, VIDEO 1, VIDEO 2)
7) Pixel shift
Select auto pixel shift (On, Off)
The Option Menu can be selected from the following 8 modes by pressing the ▲or ▼key.
OPTION MENU
OSD Language Selectable OSD Menu Language
Blending Adjust blending for OSD Menu and Main window
OSD Duration Setting Duration time of OSD Menu
Restore Factory Default
Software Update(USB)
Key Lock Locking the button(prevent operation)
DPMS When input signal is the no signal, DPMS "on" change
the power saving mode.
Cycle setup Select auto input source
Installation and User's Guide
15

1) OSD Language
As shown in the figure below, OSD Language can be selected by "▲, ▼" key.
2) Blending
OSD Menu Blending can select 4 modes as Off, Low, Middle, High by pressing the “▶ SELECT” key.
3) OsdDuration
OSD menu Duration can select 4 modes as 5, 10, 15Sec and Off by pressing the “▶ SELECT” key.
4) Restore Factory Default
Restore factory default can be selected by pressing the "▶SELECT" key. Select Yes or No by
the “◀, ▶" key.
5) Software Update(USB)
Software update default can be selected by pressing the "Menu" key. Select Yes or No by
the “◀, ▶" key.
Installation and User's Guide
16

6) Key Lock
Key lock default can be selected by pressing the "▶SELECT" key.
7) DPMS
The function can be activated(ON) or deactivated(OFF) with the button ▶.
8) Cycle setup
Select auto pixel shift with the button ▶.
Input Source can be selected from the following four input modes by using the ▲and ▼
keys when the window as shown below is displayed by pressing the "SOURCE / ▼" key
in the Main window.
(Input Source can be selected by ▲and ▼key when window shown as below. To be in this menu,
pressing the “ENTER” / ▶" key in the Main window.)
Audio Volume can be increased or decreased by pressing "VOL- / ◀", "VOL + / ▶" Key.
INPUT SOURCE
AUDIO VOLUME
Installation and User's Guide
17

5. FEATURE
General Features ULE-185U REV.F
Display
Screen Size
18.5 inches
Resolution
1366*768
Pixel Pitch
0.300*0.300 mm
Brightness
250 cd/m²
Contrast Ratio
1000:1
Aspect Ratio
16:9
Viewing Angle (H/V)
170/170 degrees
Display Color
16.7 million
Response Time
14 ms
Video System
NTSC/PAL
Panel Life Time (hours)
30,000 hours
Interface
Video In/Out (BNC Type)
2/2
VGA In (15Pin D
-Sub) 1
HDMI In
1
SDI
In/Out 1/1
Audio In(RCA Type)
2
PC Stereo In
1
Special
Features
Built in Speakers
Y (1W*2)
Remote Control
Y
Filter Type
3D Comb filter
Deinterlacing
Y
Trigger Source Switching
Y
Noise reduction
Y
Auto source sequencing
Y
Multilingual Language
Eng, Spa, Fre, Ger, Ita
Dimension
Outline Dimension
(with Stand)
17.64” x 11.72” x 3.58”
Cabinet
Cabinet Material
Electro-Galvanized Steel
Power
Electrical Ratings
DC 12V
Circumstance
Operating
Temperature 0~50 Celsius
Storage Temperature
-20~60 Celsius
Mounts
VESA Mount Size
100x100 mm
Ceiling Mount
CMK-01
Wall Mount
WB-5, 10, 30, 31
Rack
Mount RMK-08
Installation and User's Guide
18

6. TROUBLESHOOTING
* When the following troubles are occurred, follow the trouble shooting.
Before contacting service center.
Troubleshooting Troubleshooting Tip
The screen doesn’t
show up
1. Make sure if the power supply is connected property
2. Turn on the power.
3. Select the input signal right for the connected port.
The screen is too light
or to dark Control the BRIGHTNESS
The screen size is not fit
for the PC signal
Press the AUTO key among keys in the front.
(It is used only in the PC signal)
The screen color shows
strange in the PC signal In the FUNCTION menu of OSD menu, perform the AUTOADJUST.
The key pad does not work Press ▲and ◀button on the key pad for 10 seconds.
Installation and User's Guide
19

IKEGAMIELECTRONICS,(U.S.A.)INC.
HEADQUARTERS:300ERoute17S,Mahwah,NJ07430
Phone(201)368‐9171Fax(201)569‐1626www.ikegami.com