Ikegami LCM-971 User manual

- 1 -
Installation and User’s Gui
de
INSTRUCTION MANUAL
9.7” LCD VID O MONITOR
Model :
Please read this manual thoroughly before use and keep for future reference.
LCM-971

- 2 -
Installation and User’s Gui
de
* Follow this safety instruction to use the monitor properly and prevent the damages.
* Keep this user’s guide book for later use.
Warning Statements
* This safety instruction has “ Warning” and “ Caution” as below.
WARNING: If the user does not follow this instruction,
it may cause the serious damage to the user.
CAUTION: If the user does not follow this instruction, it may cause the slight
damage to the user or cause some damages to the monitor.
Never remove the back over and touch
the inside of the monitor. If you need a
service, please contact the service center.
Keep away the monitor from the
direct sunlight and a heating appliance.
Never push objects of any kind into this
product as they may result in a risk of fire
or electric shock.
Connect the power code to the wall
outlet tightly. If the power code or plug are
defective and the wall outlet is not tight,
please do not use them.

- 3 -
Installation and User’s Gui
de
Warning Statements
Do not install this monitor on the outside
and near water. If may cause damage to
the product, electric shock and fire.
or cleaning do not use liquid cleaners.
Never touch the power plug with wet-
hands.
When lightning and thundering, unplug
the monitor from the wall outlet and never
touch it.
Unplug this product from the wall outlet,
when It does not operate for a long time.
When smoking and noising from the
monitor, unplug the product from the wall
outlet and contact a service center.
How to fix
1. Do not open this product as it contains high voltage inside.
2. It may create an electric shock.
3. It the user disassembles and remove the back cover, it does not make sure
4. To make up for the damages and do a service and exchange the monitor..

- 4 -
Installation and User’s Gui
de
Cautions
Install this monitor some distance
rom the wall and do not install unless
Proper ventilation is provided.
Place this product on a stable place.
If not, it may fall, causing serious
Damages to the monitor and people.
The openings must not be blocked by
curtain, rug or other similar surface.
When carrying this monitor, be careful
not to damage the panel and drop it
It may cause some trouble.
Before carrying the monitor, tum it off and
Unplug the signal cables and the power code
rom the wall outlet.
Take the power plug out from the wall
outlet. Do not pull the cable. It may snap the
inner wires and cause overheating and fire.
Install this monitor about 50cm far from
the eyes and an angle of 0~15 degrees
below eyes. Too close installation may
cause having weak sight.
Do not press the LCD panel with hands or the
sharpened material hardly.
or cleaning, unplug the monitor from the Wall
outlet. Do net use the liquid cloth. Use the soft
cloth.
Do not use the chemical liquid for cleaning. It
may cause fading and breakage.

- 5 -
Installation and User’s Gui
de
TABLE OF CONTENTS
1. INSTALLATION .................................................................................................................
1
.1
Unpacking
……
.....
....
.
.......................................................
.................
.................
...........
2
.
OSD S TTING
…
...
....
.
.......................................................
.................
....................
....
..
3. SP CIFICATION .............................................................................................................
..
.
5. TROUBL SHOOTING
..
....
.
.......................................................
.................
....................
6. LIMIT D WARRANTY
..
....
.
.......................................................
...........
......
..
...................
.
1
.
3
Main unctional Button
s
……
.....
...
.
.
.......................................................
.................
........
4. APP NDIX
..
....
.
.......................................................
................
.........................
1
.2
Part List
……
.....
....
.
.......................................................
.................
............................
1
.4
Connection
……
.....
....
.
.......................................................
.................
..
........................
6
6
8
-
1
1
1
3
13
7
1
1
6
8
1
2

- 6 -
Installation and User’s Gui
de
INSTALLATION
1.1 Unpacking
Remove the package cover and place the product on a flat and secure surface or in the installation
location. This equipment should be unpacked and handled with care. If an item appears to have been
damaged in shipment, notify the shipper immediately. Check whether all the following device and
accessories are included with the main system. If any items are missing, notify your Sales or
Customer Service Representative.
1.2 Part List
The following table lists the parts included:
MONITOR USER’S GUIDE EXTERNAL POWER CABLE
POWER ADAPTOR
VGA CABLE

- 7 -
Installation and User’s Gui
de
INSTALLATION
MENU / EXIT
Activates and exits t e OSD.
SOURCE / ▽
▽▽
▽
Select input source, and move t e OSD menu.
AUTO / △
△△
△
Move t e OSD menu and auto adjustment of RGB source.
◁
◁◁
◁ / VOL
Decrease t e level of volume and move t e previous menu.
Enable Key lock On/Off control w ile it is pus ing for 3 second.
▷
▷▷
▷ / SELECT
Increase t e level of volume and select t e OSD menu.
/ POWER
Turns t e power ON or OFF. T ere will be a few seconds delay before t e display appears.
T e power LED(next to t e power switc ) lig ts wit green w en t e power is turned ON.
T e power is turned off by pressing t e power switc again and t e power LED goes Red.
LED LAMP
Power ON Indicator
SPEAKERS
1.3 Main Functional at Front Panel
1
2
3
4
5
6
7
8
8
8
1
2
3
4
5
6
7

- 8 -
Installation and User’s Gui
de
1.4 Connection at Back Panel
1
2
3
4
5
6
7
8
9
10
11
1. HDMI Input
2. AV1 Input
Composite signal input for AV 1.
3. AV1 Output
Video Looping output for AV 1.
4. AV2 Input
Composite signal input for AV2.
5. AV2 Output
Video Looping output for AV 2.
,7. AUDIO1 IN
Stereo audio signal input.
T is input for AV1 and S-VIDEO.
8. S-Video Input
Y/C separated signal input.
9. PC AUDIO Input
10 RGB Input
11. DC 12V Input

- 9 -
Installation and User’s Gui
de
O
SD (On Screen Display) SETTING
■ A. INPUT Select
Inputs can be set to AV1, AV2, S-VIDEO, HDMI and PC mode.
1. Press t e SOURCE button and t en ▲/▼ Button to move t e source
2. Press t e ▶ button to select t e source.
3. Press t e MENU/EXIT Button to exit t e INPUT menu.
■ B. MENU SELECTION
1. Press t e MENU/EXIT key to access t e main menu.
2. Use t e  and  arrow key to ig lig t a selection.
3. Press t e ►/SELECT key to select an item.
4. Use t e  and  arrow key to ig lig t a selection.
5. Use t e ◀ and  arrow key to adjust t e setting on a selected item.
■ C. PICTURE MENU on OSD
C. 1 INPUT SOURCE (AV1, AV2, S-VIDEO, HDMI)
- OSD Menu is working on after it connects the source signal.
AV1, AV2, S
-
VIDEO
HDMI

- 10 -
Installation and User’s Gui
de
1. Press t e MENU/EXIT Button and t en ◀ / ▶ Button to select t e PICTURE menu.
2. Press t e ▲ or ▼ Button and t en button to select t e Button to select t e adjustment item you
need.
3. Press t e ◀ or ▶ Button to active t e item.
Ex) if you select t e BRIGHTNESS, t en t e below picture appears on t e bottom screen.
4. Press t e MENU/EXIT button to move to t e previous menu.
C.2 INPUT SOURCE (PC Mode only)
5. Press t e MENU/EXIT Button and t en ◀ / ▶ Button to select t e PICTURE menu.
6. Press t e ▲ or ▼ Button and t en button to select t e Button to select t e adjustment item you
need.
7. Press t e ◀ or ▶ Button to activate t e function.
Ex) if you select t e BRIGHTNESS, t en t e below picture appears on t e bottom screen.
8. ‘Auto’ function is adjusting t e location of screen by receiving t e sync signal from PC.
Ex) Resolution c ange.
9. ‘Color Auto’ is adjusting t e optimum color coordination automatically.
■ D. VOLUME MENU on OSD (AV1, AV2, S-VIDEO, PC, HDMI)
1. Press t e ▶/Enter button for adjusting t e volume up and down.