IINNSSTTAALLLLAATTIIOONN
LLEENNSS HHOOOODD ##66001155..33 MMGG HHDD33 OONNLL____________________________________________________________________________
Rotate and remove the Lens Hood, and install lens the shade before installing
camera in the housing.
FFIINNAALL PPRREEPPAARRAATTIIOONN__________________________________________________________________________________________________________________
Remove the lens cap and cord from the camera.
Otherwise, they may interfere
with the housing seal.
The camera's auto focus feature is utilized underwater. For best results, move in
close to your subject and use the wide angle range to shoot thru as little water as
possible. The full zoom range is accessible underwater.
Turn the camera’s built-in flash OFF.
Chart shows recommended initial settings
underwater.
WWHHIITTEE BBAALLAANNCCEE__________________________________________________________________________________________________________________________
Initially set the white balance to Auto. Use the joy stick controls on the housing
to change white balance.
CCoolloorr FFiilltteerr::When using the color filter (during the day), set camera white balance
to Indoor for 0-15 foot depth. For 15-80 foot depth, set white balance to Outdoor.
VViiddeeoo--LLiittee::When using optional Video Lite at NIGHT, set the camera white balance
to the Indoor position. During the DA , use the Outdoor setting for subjects beyond
4-5 feet and the Indoor setting for closer subjects.
CCAAMMEERRAASSEETTTTIINNGG
Power On/Off – Camera (On)
Zoom Lever – Wide Angle Setting
Focus – Auto Mode
Exposure – Auto Mode
Auto Lock – Center Position
Program AE – Auto Mode
Shutter Speed – 1/60 Normal
White Balance – Auto Mode (see section)
Steady Shot – Off
Built-in Flash – Off
IINNSSTTAALLLLAATTIIOONN
CCAAMMEERRAA TTRRAA__________________________________________________________________________________________________________________
Note the placement of the camera tray underneath the guides, and note the
white-color locks on the inside wall of the housing
that secures the tray in place. Gently push up
on the white tray locks to release the camera
tray, and slide the tray out of the housing.
Place the camera against the stabilizing
pins on the tray and secure with the tripod
mounting bolt. The camera should fit easily
on the tray and should be parallel with the sides
of the tray.
Make certain that the lens shade has been
threaded completely into the camera to avoid any potential
clearance or sealing problems when the camera is installed and the housing is sealed.
IINNSSEERRTTIINNGG TTHHEE CCAAMMEERRAA______________________________________________________________________________________________
Check that the o’ring is clean and properly positioned on the lip of the clear
housing back plate. Check that the lens shade is completely threaded into the camera.
Once the camera is mounted to the tray as shown above, pull the housing
controls out to provide clearance for installing the camera. Partially slide the camera
into the housing so you can connect the reversing circuit cable to the blue LANC port
on the camera. Make sure the lens shade on the front of the camera fits into the
port recess in the front of the housing.
DDOO NNOOTTforce this installation; the camera and tray should slide easily into place
so the housings back plate o’ring is resting against the main housing body. In this
position the lid snaps can be positioned over the lid hooks on the housing back plate
and snapped into position to seal the housing.
HHOOUUSSIINNGG CCOONNTTRROOLLSS________________________________________________________________________________________________________________
Slide the housing controls back in place making sure they properly align with
the camera functions.
Operate each control to see how it works with the camera. Some controls such
as start/stop will be used frequently. Other controls may seldom be utilized. Refer
to your camera owner's manual for the proper function of each camera control.
Look thru the back to be sure that you can see into the viewfinder.
When using the housing controls, especially the start/stop, do NOT use excessive force
because you could damage the camera.
CCAAUUTTIIOONN
Remove the lens cap and cord from the camera. Otherwise, the cord may interfere with the housing seal.
If the housing controls are not properly positioned, they could interfere with the housing seal.
MMAANNUUAALL FFOOCCUUSS OOPPEERRAATTIIOONN______________________________________________________________________________________________
Manual focus may be preferred in low light levels or when the subject possesses
little contrast. Set the focus switch to Manual to cancel the auto focus. If you want
to manually adjust the focus, rotate the manual focus control as desired. To reacti-
vate the auto focus, set the focus switch to Auto.
IIKKEELLIITTEE UUNNDDEERRWWAATTEERR SSSSTTEEMMSS
50 West 33rd Street • PO Box 88100 • Indianapolis, IN 46208 USA • 317.923.4523
6015.3-01-1107
