ikonic Privacy Lever Set User manual

Fellino Lever Set
Very Important!
Fellino Privacy Lever Set is designed to suit either left or right hand opening doors. Privacy Pin can be top or bottom depending on which
side your door is hinged.
Please fasten all screws by hand and not an electric screwdriver or drill, as over tightening is not recommended.
Instructions to install the Fellino Privacy or Passage Set.
If installing this lever set into a new door you will need the following tools: 25mm spade bit, 2mm drill bit, 54mm hole saw, corded or cordless drill, hammer, wood chisel, Phillips
head screwdriver, tape and pencil. If you are replacing an existing door handle you shouldn’t require the drill, hole saw or spade bit as it will replace most standard door knobs and
lever sets.
WARRANTY CONDITIONS
Any claim under this warranty must be made within 1 year of the date of purchase of the product. To make a claim under the warranty, take the product (with proof of purchase) to any Bunnings store (see www.bunnings.com.au for store locations). Romak
Hardware Distributors Pty Ltd bears reasonable, direct, expenses of claiming under the warranty. You may submit details and proof to our store for consideration. The warranty covers manufacturer defects in materials, workmanship and finish under normal use.
This warranty is provided in addition to other rights and remedies you may have under law: our goods come with guarantees which cannot be excluded under the Australian Consumer Law. You are entitled to replacement or refund for a major failure and
compensation for other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The warranty excludes damage resulting
from product misuse or product neglect. The warranty covers domestic use only and does not apply to commercial applications. This warranty is given by Romak Hardware Distributors Pty Ltd, ABN 15489950457, 177-181 Atlantic Drive, Keysborough Vic 3173,
[phone], E-mail: [email protected]. New Zealand customers please contact HARCO (Harkness & Young Ltd), 9 27 64071, Email: [email protected]. ‘Romak’ is a TM. © Romak.
Suits models 600310, 600320. 01565
Step 1: Preparation
Cut template on line (A) & fold on line (B) as shown.
Place on door at your preferred height and mark both
the latch height (C) and centre of handle hole (D) with
a pencil.
Remove template, and measure the thickness of door
to mark the centre point of the door edge.
Use a 25mm spade bit to drill an accurate hole through
the door edge, and using a hole saw, drill a 54mm hole
through the door front.
Accuracy is vital so mark and measure carefully and
drill holes level.
Step 2: Installing the Latch
Place Latch (E) into 25mm hole
on side of the door and using
sharp pencil mark door around
the square plate, using hammer
and chisel check out the timber
so that the latch fits into the
newly created recess and finishes
flush with door.
Once completed push latch into
place and drill 2mm pilot holes
into edge of door, simply use
screwdriver to insert the timber
screws included.
Line B
Line A
C
D
60mm
(or 70mm)
E
K
F
L
L
M
F
O
70mm
60mm
70mm
60mm
Template for new doors using 54 mm hole saw.
60 mm
70 mm
Latch Height
C
Latch Height
C
Line B
Line A
Fold to Door Edge
Line B
Fold to Door Edge
D
Line B
Line A
C
D
60mm
(or 70mm)
E
K
F
L
L
M
F
O
70mm
60mm
70mm
60mm
Template for new doors using 54 mm hole saw.
60 mm
70 mm
Latch Height
C
Latch Height
C
Line B
Line A
Fold to Door Edge
Line B
Fold to Door Edge
D
Line B
Line A
C
D
60mm
(or 70mm)
E
K
F
L
L
M
F
O
70mm
60mm
70mm
60mm
Template for new doors using 54 mm hole saw.
60 mm
70 mm
Latch Height
C
Latch Height
C
Line B
Line A
Fold to Door Edge
Line B
Fold to Door Edge
D
Step 3: Attaching the Levers to door
Start by removing the door plate cover (M) from the outside handle. Make sure Spindle (F)
is inserted into Latch. Insert the Lever (L) into the Spindle (F) by guiding the Lever onto the
spindle, ensuring the two screw holes align.
Now insert the two screws (K) and tighten. Place the cover (M) over the handles and onto the
Lever base so that they finish against the door.
How to convert Latch from
60mm to 70mm
Slide tab from the marked 60mm
position to the 70mm position.
Line B
Line A
C
D
60mm
(or 70mm)
E
K
F
L
L
M
F
O
70mm
60mm
70mm
60mm
Template for new doors using 54 mm hole saw.
60 mm
70 mm
Latch Height
C
Latch Height
C
Line B
Line A
Fold to Door Edge
Line B
Fold to Door Edge
D
Move tab from
60mm to 70mm

Fellino Lever Set
Line B
Line A
C
D
60mm
(or 70mm)
E
K
F
L
L
M
F
O
70mm
60mm
70mm
60mm
Template for new doors using 54 mm hole saw.
60 mm
70 mm
Latch Height
C
Latch Height
C
Line B
Line A
Fold to Door Edge
Line B
Fold to Door Edge
D
Drilling template - 60mm or 70mm Latch