IKUSI MAC HOME AV-COFDM User manual

MAC HOME
REF. 4488
AV-COFDM Stand Alone Modulator
User Guide

2

3
4 General safety instructions
4 Types of notices
4 Basic safety instructions
5 Introduction
5 General description
5 Main features
6 Technical specifications
6 MAC HOME Model
7 Unit installation and configuration
7 Installation
7 Power supply connection
8 Cascade installation
8 General use of the unit
9 Fast menu guide
10 Initial configuration of the unit
10 Advanced configuration of the unit
10 Blocking the LCD and Joystick
11 Firmware update
11 Configuration of the input signals
11 Configuration of the carrier services
12 Configuration of the output signal
12 Network configuration
14 Status of the unit
14 Unit information
14 Unblocking the unit
15 USB PLAYER Video playback through USB port
17 Maintenance
17 Warranty
17 Unit recycling
18 Characters table
18 CE Certificate
Contents EN

4
General safety instructions
JRead all of this user manual carefully before plugging in the unit.
JAlways have these instructions to hand during installation.
JFollow all of the instructions and safety notices regarding unit handling.
Types of notices
The meaning of the safety notices used in this manual are described below.
DANGER OF DEATH OR INJURY
This safety notice indicates a possible danger for the life and health of people. Not following these
instructions may lead to serious consequences to health and may even cause fatal injuries.
RISK OF DAMAGE TO THE UNIT
This safety notice indicates a possible dangerous situation. Not following these instructions may lead
to the unit being damaged.
NOTE
This type of notice is a note containing applicable advice and useful information for optimum use of
the unit.
HANDLING THE INSIDE OF THE UNIT IS FORBIDDEN
This notice forbids any work that may affect the working order of the unit or its warranty.
DO NOT DISPOSE OF AS URBAN WASTE
This type of notice indicates that the unit must not be disposed of as unselected urban waste.
Basic safety instructions
DANGER OF DEATH OR INJURY
JDo not install the unit during an electrical storm. This could lead to electrostatic discharge from
lightning.
JDo not open the unit. There is a risk of electrostatic discharge.
RISK OF DAMAGE TO THE UNIT
JThe unit must be appropriately ventilated. Install the unit in a dust-free location. Do not place the
unit in a location where the ventilation slots are covered or blocked. Install the unit in a location
with at least 20 cm around it free of other objects.
JDo not expose the unit to rain or moisture. Install the equipment in a dry location with no inltra-
tion or condensation of water. Should a liquid enter the unit, disconnect it immediately from the
mains.
JKeep the unit away from ammable objects, candles and anything that may cause a re.
JConnect the unit to an easily accessible power socket. In the event of an emergency, it will then
be possible to quickly unplug the unit.
JDo not expose the unit to sources of heat (sun, heating, etc.).
DANGER
ATTENTION
DANGER
ATTENTION

5
Introduction
General description
Main features
The Mac Home model is an AV analogue TV signal to COFDM digital TV signal standalone modu-
lator unit. Suitable for individual residential installations, it is an ideal solution for the distribution of
analogue video signals with COFDM digital TV modulation in a single standalone unit.
The AV signal is digitalised, coded in MPEG2 MP@ML, H.264/MPEG4 AVC MP L4.1 and modu-
lated in COFDM. The base band signal is modulated on an RF carrier that can be adjusted at the
output to the UHF bands.
The modulator is capable of playing videos generated by the user.
Programming:
FUser interface with LCD display and control button for basic conguration.
FAll settings are automatically memorised.
FReprogrammable as many times as required.
FVideo playback through USB port.
FFirmware update via USB connection.
KEY
Power Supply
Display (LCD)
Control button
Mains connector
S-Video & component Video (YPbPr, RGB) *
C-VBS vídeo input
L & R analogic audio inputs
USB input (video playback and
rmware actualization)
TV Loopthrough input
TV COFDM output
* S-Video to RCA cable supplied.





 
    











6
Technical specifications
MAC HOME
Input AV
Format CVBS, S-VIDEO, YPbPr, RGB*
Input level (video) Vpp 0.7 ... 1.4
Input impedance Ω 75
Video standards PAL/SECAM/NTSC/B&W
Audio standards 1 x mono/stereo
Input level (audio) Vpp 0.5 ... 2.5
Compresion
Video MPEG2 MP@ML, H.264/MPEG4 AVC MP L4.1
Video resolution 720x576, 25 fps (PAL), 720x480, 30 fps (NTSC)
Video Bitrate MBits/s 4 - 10
Audio MPEG1 Layer II
Audio Bitrate KBits/s 96, 128, 160, 192, 224, 256, 320, 384
DVB Processing
Insertion tables PAT, PMT, SDT, NIT
Conguration Channel Name, SID, LCN, NID, Network Name, Provider Name,
TSID, ONID, NIT MODE, LCN Private Descriptor
Output DVB-T according to ETSI EN 300 744
Bandwidths MHz 6 / 7 / 8
Number of carriers 2K / 8K
MER dB ≥ 35
Central frequency MHz 474 - 858
Level dBμV ≥ 80
Output pitch attenuation dB ≤ 1.5
Level adjustment dB -25
Frequency stability ppm ≤ ±30
Noise gure (∆B = 8MHz) dBc ≤ -45
General
Mains voltage VAC 230 - 240
Consommation W 8.1
Operating temperature ºC 0 to 45
Mains connector IEC C8
Power supply VAC 230 - 240
Dimensions (without connectors) mm 210 x 114 x 32
Weight kg 1
Video input connectors 1 RCA (CVBS) ; 1 MINI DIN (S-VIDEO) ,
Y Pb Pr, RGB (adapter cable included) ; 1 USB
Audio input connectors 2 RCA (L & R)
Local interface LCD + Joystick
Application software USB PLAYER included
Update Yes
* RGB with sync on green

7
Unit installation and configuration
The LCD display and the control button are sufcient for the basic settings of the unit. Follow the
steps indicated below to install the unit and congure the various parameters accessible from the
user interface on the LCD display.
Installation
RISK OF DAMAGE TO THE UNIT
Mechanically handling the unit may result in
damage. Do not connect the unit to the power
supply before or during assembly.
1) Mount and tighten the screws and plugs to secure
the unit to the wall. (*)
2) Connect the AV input in the respective RCA con-
nectors or S-Video connector.
3) Optionally, connect the loop-through RF input
coaxial cable (F connector).
4) Connect the coaxial output cable to the unit (F
connector).
(*) The 3 wall attachments are supplied disassembled in order
to install the unit horizontally. The straightforward assembly
consists of positioning the fastenings in the corresponding
holes and pushing as far as possible (they cannot be remo-
ved once inserted).
NOTE. It is recommended to mount the unit vertically.
Power supply connection
DANGER OF DEATH OR INJURY
Incorrect unit power connection may cause an electric shock. Follow the steps below for
the electrical installation of the unit.
1) Connect the earth cable.
2) Connect the power plug to the unit mains connector.
3) Connect the power plug to the mains socket.
ATTENTION
DANGER
vídeo
audio L audio R
S-Video


Ref.4488
AV COFDM MODULATOR
USB
1
DVD IRDCAM
2
3 4














8
Cascade installation
The MAC HOME unit has 1 AV analogue TV signal to RF UHF output encoded as COFDM Digital
TV signal.
Several MAC HOME units can be cascaded in order to increase this capacity. The maximum capa-
city of a series of N units is 1xN incorporated TV signals. To cascade 2 or more units, connect the
RF output of the preceding unit to the TV input (loop-through) of the next unit (see illustration).
The MAC HOME unit automatically adjusts the TSID and SID values when programming the chan-
nel of each modulator.
General use of the unit
Below is described how to operate the unit using the control button and interpret the visual indi-
cations on the LCD display. The program comprises a main menu made up of sub-menus that can
be selected to modify the basic operation settings of the unit.
Visual indications on the LCD display
In the menus and submenus, move the button up or down to browse upwards and
downwards position by position.
In the settings, move the button up or down to modify values position by position.
Keep the button pressed up or down to browse or to modify values more quickly
Horizontal button movement
In the menus, move the button to the left or the right to select and go back position by
position.
In the settings, move the button to the left or the right to select and go back position by
position.
Keep the button pressed to the left or to the right to browse more quickly.
Press button
In the menus, this selects the submenu.
In the submenus, this selects the setting.
In the settings, this selects the parameter value.




 






 







9
Fast menu guide
 COUNTRY
 SPAIN
OUTPUTCHANNEL
 ATTENUATION
 COUNTRY
 insertcountry
CHANNEL
 21
COUNTRY
 LANGUAGE
 COUNTRY
 AUSTRALIA
**WARNING**
CANCELUPDATE
CHANNEL
 21
FREQUENCY
474.000MHz
ATTENUATION
1.00dB
OFDMMODE
2K
BANDWIDTHS
8MHz
GUARDINTERVAL
1/32
CONSTELLATION
64QAM
CODERATE
7/8
NAME
Standard
PROVIDER
IKUSI
NID
00001
TSID
00001
ONID
00001
NITMODE
OFF
NITLCNMODE
EuropaMODE
STATUS
 MODULEINFO
STATUS:OK
ALARM:OK
OUTPUTBITRATE
31.670MBits/s
ACTMINNULLMAX
100%100%100%
MODEL
MACHOME
SERIALNUMBER
012345678911
V.SWV.HWV.BS
1.001.012.32
MACHOME 1.00LOCKCODE

LOCKCODE
 0000
SERIALNUMBER
 012345678911
THE EQUIPMENT IS INSTALLED
OUTPUT

 IKUSI
 MACStating...
 GENERAL
SETTINGS
INPUT
 SERVICES
OUTPUT
 NETWORK
LOCKCODE
 OFF 000O
LOCKLCD

GENERAL

FACTORYRESET
**WARNING**
CANCELFORMAT
SERVICES
INPUT

CH1:PAL BRIGHT
 V:XA:X 128
CONT SATURATION
 066 063
INPAUDIO ATT
 20
SHARPNESS
MEDIO
CODING
MPEG2
ASPECRATIO
4:3
AVMODE
AUTO
VIDEOBITRATE
08.000MBits/s
AUDIOBITRATE
128KBits/s
CHVIDEOAUDIO
 ONOFF
CHLCN
 001
CHSID
 0021
CHNAME
 CH1

SETTINGS
STATUS

MODULEINFO
NETWORK
SYSTEMUPDATE NOUSB

INFORMATION
INITIAL Installation
 MACHOME 1.00
 CH21 SYSTEMOK
ADVANCED Installation
 MACHOME 1.00
 CH21 SYSTEMOK
OUTPUTCHANNEL
 ATTENUATION
COUNTRY
 LANGUAGE
 submenu
 main menu
ATTENUATION
12dB
STANDARDTV
PAL
ADVANCEDMODE

10
Main menu
NOTE
Over the following pages, the eld locating and selection method is primarily indicated
by the “vertical button movement” and “press button” icons.
1) Once the unit is started up, the start screen asks for the
COUNTRY to be entered. Move the button to the right and the
cursor will ash next to the rst country, then move the button
down until you nd the reference country. OK to save
* The unit automatically adjusts to the technical peculiarities of
this (see default parameters table).
2) Move to the left and place the arrow on LANGUAGE, then
move the button to the right and locate the required language
by moving the button vertically. OK to save.
3) Move to the left through to the start screen, which shows the
model, rmware version, channel and status.
STATUS:
 SYSTEM OK = status correct.
 NO INPUT = input signal not detected
 SYSTEM NOK = status incorrect.
Configuration of the output signal
1) From the start screen, move the button to the right through to
the OUTPUT CHANNEL. The cursor will blink next to the chan-
nel.
2) Use horizontal scrolling to move between the digits and vertical
scrolling to change the value. OK to save.
THE UNIT IS INSTALLED!
Advanced mode
From the start menu, move a step to the right and down to locate
the ADVANCED MODE screen.
General
From the GENERAL screen, move the button to the right to ac-
cess the following menus:
Block the LCD and Joystick
1) Locate and select the option LOCK LCD to block access to
the conguration of the unit from the LCD display and using
the control button.
a) Enable (ON) or disable (OFF) the blocking option.
b) Set a code to unblock the unit whenever this option is
enabled.
Restoring factory setting
1) Locate and select the option FACTORY RESET to restore the
factory settings of the unit.
Select the option FORMAT to delete all the modications entered
in the conguration by the installer or operator of the unit.
OTPUTCHANNEL
 ATTENUATION
 MACHOME 1.00
 CH21 SYSTEMOK
 COUNTRY
 insertcountry
CHANNEL
 21
ADVANCEDMODE

 COUNTRY
LANGUAGE
 COUNTRY
 AUSTRALIA
 MACHOME 1.00
 CH21 SYSTEMOK
BLOCKLCD
 RESETFABRICA
GENERAL
 SETTINGS
LOCKCODIGO
 OFF 000O
GENERAL
 SETTINGS
LOCKLCD
FACTORYRESET
**WARNING**
CANCELFORMAT

11
Firmware Update
1) Locate and select the option SYSTEM UPDATE.
a) Download the update package from the website (www.ikusi.com).
b) Unzip and place in the root directory of a USB (may not
match a playback le named “video-nal.ts”).
c) Insert the USB in the connector in the unit.
Settings the signals
NOTE
The unit can switch the input signals; alter their brightness, contrast and saturation con-
ditions; and adjust the output carrier in RF.
Locate and select the option SETTINGS
Configuring the input signals
1) Locate and select the option INPUT.
a) Locate and select the option CH1 BRIGHT to check the type
of input signal (PAL), the video (X) and audio (X) detection,
and congure the brightness of the video signal (1 to 255).
b) Locate and select the option CONT SATURATION to congu-
re the contrast and saturation of video signal (1 to 255).
c) Locate and select the option INP AUDIO ATT to congure the
attenuation of audio signal in dB (1 to 40).
d) Locate and select the option SHARPNESS to congure the
sharpness of video signal (High, Medium soft or None).
e) Locate and select the option CODING. This congures the
coding parameters: MPEG2 H.264/MPEG4 AVC.
f) Locate and select the option ASPECT RATIO. The possible
aspect ratio values are 4:3 and 16:9.
g) Locate and select the option AV MODE. The possible values
are AUTO (automatically detects the signal type, excepting
RGB), C-VBS, S-Video, YPbPr, RGB *.
* RGB with sync on green.
h) Locate and select the option STANDARD TV. The possible
values are PAL and NTSC,(automatically updated when you
change the country).
i) Locate and select the option VIDEO BITRATE. The unit can
be congured for a data coding speed at input of 4 to 10
Mbits/s.
j) Locate and select the option AUDIO BITRATE. The unit can
be congured for a data coding speed at input of 96; 128;
160; 192; 224; 256; 320 and 384 Kbits/s.
NOTE
If you keep pressing the control button down you will accessthe information and con-
guration of the following input signals.
Configuration of the carrier services
1) Locate and select the option SERVICES.
a) Locate and select the option CH VIDEO AUDIO. Activate
(ON) or deactivate (OFF) the video and audio signals of the
rst input.
SYSTEMUPDATE

**WARNING**
CANCELUPDATE
GENERAL
SETTINGS
INPUT
 SERVICES
CH1:PAL BRIGHT
 V:XA:X 128
CONT SATURATION
 066 063
INPAUDIO ATT
 20
SHARPNESS
NONE
CODING
MPEG2
ASPECTRATIO
4:3
AVMODE
AUTO
VIDEOBITRATE
08.000MBits/s
AUDIOBITRATE
128KBits/s
INPUT
SERVICES
CHVIDEOAUDIO
 ONOFF
STANDARDTV
PAL

12
b) Locate and select CH LCN. Congure the LCN value of the
signal.
c) Locate and select CH SID (used by default as output chan-
nel). Service set identier.
d) Locate and select CH NAME. Assign a name to the signal
in CH. See characters position at the nal of the user guide.
NOTE
If you keep pressing the control button down you will access the information and con-
guration of the following input signals.
Configuration of the output signal
NOTE
To introduce a sequence of digits in the display move the control button vertically to
change the value of the current digit and horizontally to move between digits.
NOTE
Position the cursor to the right of the current value and move the control button vertically
to increase or decrease the current value. Hold the control button up or down to increa-
se or decrease the current value more quickly.
1) Locate and select the option OUTPUT.
a) Locate and select the CHANNEL. This option automatica-
lly changes the frequency, adapting to the center of the
channel.
b) Locate and select the option FREQUENCY. This option
modies the value of the channel, adapted to the frequency.
Congure the output frequency value between 474MHz and
862MHz increments of 125 kHz.
c) Locate and select the option ATTENUATION. Select the
output attenuation between 0 and 25,5dB.
d) Locate and select the option OFDM MODE. Select the
OFDM mode between 2K and 8K subcarriers.
e) Locate and select the option BANDWIDTH. Select the band-
width between 6, 7 and 8Mhz.
f) Locate and select the option GUARD INTERVAL. Select the
guard interval between 1/32, 1/16, 1/8 and 1/4 of symbol.
g) Locate and select the option CONSTELLATION. Select the
modulation constellation between 16QAM and 64QAM.
h) Locate and select the option CODE RATE.
Select the code rate between 1/2, 2/3, 3/4, 5/6 and 7/8.
Network configuration
NOTE
To introduce a sequence of digits in the display move the control button vertically to
change the value of the current digit and horizontally to move between digits.
CHLCN
 001
CHSID
 0021
CHNAME
 CH1
ATTENUATION
1.00dB
OFDMMODE
2K
BANDWIDTH
8MHz
GUARDINTERVAL
1/32
CONSTELLATION
64QAM
CODERATE
7/8
CHANNEL
 21
FREQUENCY
474.000MHz
OUTPUT
 NETWORK

13
NOTE
Position the cursor to the right of the current value and move the control button vertically
to increase or decrease the current value. Hold the control button up or down to increa-
se or decrease the current value more quickly.
1) Locate and select the option NETWORK.
a) Locate and select the option NAME. Congure the name of
the network.
b) Locate and select the option PROVIDER. Congure the
name of the network service provider.
c) Locate and select the option NID.
Congure the value of the network identier.
d) Locate and select the option TSID. Congure the value of the
trasport stream identier.
e) Locate and select the option ONID. Select the guard interval
between 1/32, 1/16, 1/8 and 1/4 of symbol.
f) Locate and select the option NIT MODE. Congure the NIT
mode :
 OFF: NIT is not inserted (the LCN values are ignored).
 ON: the NIT generated by the unit is inserted.
g) Locate and select the option NIT LCN MODE. Allows you to
select the mode of the NIT LCNs :
 OFF: the LCN descriptor is not inserted in the NIT
 EUROPE MODE: the descriptor for Europe is inserted.
 INDEPENDENT TELEVISION COMISION: the descriptor for
the UK is inserted.
 NORDIG MODE V1: the descriptor according to the Nordig
V1 specication is inserted.
 NORDIG MODE V2: the descriptor according to the Nordig
V2 specication is inserted.
 GENERIC MODE: generic LCN descriptor.
DEFAULT PARAMETERS TABLE IN ACCORDANCE WITH THE COUNTRY
SELECTED
COUNTRY LANGUAGE NIT MODE LCN MODE NID TSID ONID Bandwidth Channels Frequencies
Australia English ON Generic 1 28 8442 7 Mhz 28 - 69 526000 - 819875
France French ON Europe 1 21 8442 8 Mhz 21 - 69 470000 - 861875
UK English ON Ind Tl Com (UK) 1 21 8442 8 Mhz 21 - 69 470000 - 861875
Italy Italian ON Europe 1 21 8442 8 Mhz 21 - 69 470000 - 861875
Portugal English ON Generic 1 21 8442 8 Mhz 21 - 69 470000 - 861875
Spain Spanish ON OFF 1 21 8442 8 Mhz 21 - 69 470000 - 861875
Note:
When configuring the country, the unit is always configured with the first channel allowed, using the frequency of the centre of this
channel. This is 529.5 MHz for Australia and 474 MHz for the others.
OUTPUT
NETWORK
NAME
Standard
PROVIDER
IKUSI
NID
00001
TSID
00001
ONID
00001
NITMODE
OFF
NITLCNMODE
EuropeMode

14
Status of the unit
NOTE
The unit lets you see its status in detail and the existence of active alarms in the module.
1) Locate and indicate STATUS.
a) Locate and indicate STATUS: The unit displays its status and
alarms: OK / Error.
b) Locate and indicate OUTPUT BITRATE. The unit displays the
output data speed in Mbits/s.
c) Locate and indicate MIN ACT MAX NULL. The unit displays
the volume of null data packets in the output (minimum,
actual and maximum) as a percentage of the total.
Unit information
1) Locate and indicate the option MODULE INFO.
a) Locate and indicate the option MODEL. The unit displays its
model and version.
b) Locate and indicate the option SERIAL NUMBER. The unit
displays its serial number.
c) Locate and indicate the option V.SW V.HW V.BS. The unit
displays its software version (V.SW), of hardware (V.HW) and
star system (V.BS).
Unblocking the unit
The unit can be blocked from the web interface preventing the
user operating the display and the control button to modify the
conguration.
To unblock the unit:
1) Locate and select BLOCKING CODE.
2) Enter the unblocking code assigned by the unit operator
through the web interface
3) The unit displays the validity of the code.
NOTE
The unit will remain unblocked until it is restarted or the operator deactivates the block
from the web interface.
To unblock the unit without the blocking code:
1) Locate and select INFORMATION.
2) Contact the supplier of the unit and provide the SERIAL NUM-
BER. The supplier of the unit will provide an unblocking code
for the serial number indicated
3) The unit displays the validity of the code.
ESTADO
 INFODEMODULO
ESTADO:OK
ALARMA:OK
BITRATESALIDA
31.670MBits/s
MINACTMAXNULL
100%100%100%
ESTADO
INFODEMODULO
MODELO
MACHOME
NUMERODESERIE
012345678911
V.SWV.HWV.BS
1.001.001.00
MACHOME 1.00
COD.DEBLOQUEO
 INFORMACION
COD.DEBLOQUEO
 1030
COD.DEBLOQUEO
 CODIGOOK
 COD.DEBLOQUEO
INFORMACION
NUMERODESERIE
 012345678911

15
USB Player
NOTE
This device is used to play back videos through the USB port. Using the software, the
user can draw up a personalised list of images and videos in order to create the end le
(“video-nal.ts”), which can then be played back through the Mac Home modulator.
Check the firmware version of the unit, USB PLAYER option, available as of version 1.21.
Software to create videos for playback through the Mac Home.
See guide and application in ikusi.tv. Users should install the software on their
PC by downloading the setup le “conversor-mac-installer.exe” from the Mac
Home webpage at http://www.ikusi.tv/en/headends/modulators/mac-series/
mac-home.
USB Player Video playback
Playback will begin automatically when you insert the pen drive in the Mac Home Modulator’s USB
connector (wait for a seconds), without you having to access the menu, provided the “video-nal.ts”
le was created properly.
The USB PLAYER function overrides the modulator function. If the Mac Home is working as a
modulator, it will automatically playback the video.ts le on any pen drive you connect.

16
Maintenance
Unit care
HANDLING THE INSIDE OF THE UNIT IS FORBIDDEN
Do not dismantle or try to repair the unit, its accessories or its components. This will render the
warranty null and void.
JDo not use the power cable if it is damaged.
JTo disconnect the power cable, pull carefully on the plug and not the cable.
JTo clean the panel and unit connections:
FUnplug the unit.
FClean with a slightly damp, soft cloth.
FAllow to dry completely before use.
JDo not spill liquid onto the unit.
JKeep ventilation slots free of dust and any foreign bodies.
Troubleshooting
The most frequent problems arising during unit installation are indicated below. If you encounter any other type
of problem, please contact the unit sales team.
Problem Possible cause What to do
Forgotten unlock code ------ Contact your supplier
Nothing appears on LCD display The power cable is not connected
properly
Check the power cable
Warranty
Notwithstanding any complaints made to the direct vendor of the product, IKUSI offers unit users a two-year
warranty as of the invoice date, which shall become valid on presenting the receipt of purchase.
During the warranty period, IKUSI is responsible for any faults arising due to material or manufacturing defects
and shall repair the receiver or replace it for another corresponding to the state of technology at that time. The
warranty does not cover any faults or defects due to misuse or non-fullment of the information given in this
installation manual.
All complaints other than those indicated are not included in the warranty. More specically, the warranty does
not cover services provided by the authorised vendor (e.g. installation, conguration or programme updates) or
the repair of any damages or injuries caused to the client or others as a result of the installation or of receiver
operations.
Unit recycling
RECYCLING OF ELECTRICAL AND ELECTRONIC EQUIPMENT
(Applicable in the European Union and in European countries with selective waste collection sys-
tems.)
This symbol on your unit or its packaging indicates that this product cannot be treated as general
domestic waste and must be handed in at the corresponding point of collection for electric and
electronic equipment. By ensuring this product is disposed of correctly you will help prevent negative
consequences for the environment and human health, which could otherwise be caused by inappro-
priate waste handling of this product. Recycling of materials helps preserve natural resources. For
more detailed information on the recycling of this product, please contact your local council, your
nearest collection point or the distributor from whom you purchased the product.

17
E M C
L V D
EC-Declaration of Conformity
We, Manufacturer
IKUSI, Angel Iglesias, S.A.
Paseo Miramón, 170
E-20009 San Sebastián, Spain
declare that the product
marking
San Sebastián, October 2011
Council Directive 2006/95/CE
(Low Voltage Directive)
Standards to which conformity is declared :
and
Council Directive 2004/108/CE
(EMC Directive)
Standards to which conformity is declared :
Luis Rodríguez Navarrete
R&D Director
AV-COFDM Autonomous Modulator
MAC HOME
EN 50083-2 :2007
Cabled distribution systems for television and sound signals.
Part 2: Electromagnetic compatibility for equipment.
is in conformity with
EN 60728-11 :2005
Cabled Distribution Systems for Television and Sound
Signals. Part 11: Safety Requirements.
EN 60065 :2003
Safety requirements for mains operated electronics
and related apparatus for household and similar ge-
neral use.
Certificate
Characters table
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
w
X
Y
Z
Ä
Ö
Ñ
Ü
§
¿
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
!
#
¤
%
&
‘
<
>
*
+
,
-
.
/
0
1
2
3
4
5
6
7
8
9
:
;
◄
=
►
?
·
character position in the display

18
Safety instructions

19

Ángel Iglesias, S.A.
Paseo Miramón, 170
20014 San Sebastián, Spain
Tel. [phone]
Fax [phone]
[e-mail]
www.ikusi.tv
120167E (EN)