ILP RB3 Series User manual

INSTALLATION INSTRUCTIONS
LED ROUND HIGH BAY
CAUTION
WARNING
Installaon Steps
REFLECTOR / DIFFUSER INSTALLATION (OPTIONAL)
PLEASE READ INSTRUCTIONS BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCE.
Electrical products can cause death or injury, or damage to property. If in any doubt about the installaon or use of this product, consult a competent electrician.
· Insert provided screws to the designated locaons on the fixture housing. Install screws half way, leaving enough space (1/8"– 3mm) between the housing and
the end of the screws to be able to insert through the keyholes of the reflector/diffuser (Figure 1).
· Align the reflector/diffuser with the housing and insert screws through the reflector/diffuser keyholes. Rotate clockwise to lock the reflector/diffuser (Figure 2).
· Lock the screws to secure the reflector/diffuser (Figure 3).
· Finished result as shown in (Figure 4).
· Follow RB3 installaon steps to complete the installaon.
1. To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings
and instrucons included with and on the fixture box and all fixture labels.
2. Before installing, servicing, or performing roune maintenance on this luminaire, follow these general precauons.
3. Installaon, service and maintenance of luminaries should be performed by a qualified licensed electrician.
4. For the installaon: If you are unsure about the installaon or maintenance of the luminaire, consult a qualified licensed electrician and check your local
electrical code.
5. To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
6. Please keep the RB3 away from any corrosive substance. When you clean it, please use damp or dry cloth.
General Wiring Diagram
Black (Line)
100-277V White (Neutral)
Green (Ground)
Purple (Dim+)
Purple (Dim-)
Blue (-)
Red (+)
LED DRIVER
!
!
WARNING
1. Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
2. Turn off the power when you perform any maintenance.
3. Verify that supply voltage is correct by comparing it with the luminaire label informaon.
4. All wiring connecons should be capped with UL approved wire connectors.
5. Suitable for Wet Locaons
!
Figure 1 Figure 2 Figure 3 Figure 4
Reflector
Screw

Figure 1
Figure 3
Figure 2
Part Number Power Working Current Input Voltage Efficacy
RB3-13L-U-40
RB3-13L-U-50
RB3-19L-U-40
RB3-19L-U-50
RB3-25L-U-40
RB3-25L-U-50
RB3-31L-U-40
RB3-31L-U-50
100W
100W
150W
150W
200W
200W
240W
240W
1100mA
1100mA
1650mA
1650mA
2200mA
2200mA
2640mA
2640mA
AC100-277V 130lm/w
INSTALLATION INSTRUCTIONS
LED ROUND HIGH BAY
Installaon Steps
· Locate (2) Bracket B and aach to the designated locaons on the fixture housing with provided screws (Figure 1).
· Locate (1) Bracket A and aach to secured Bracket B, on both sides, with nylon and steel gaskets, screws and nuts (Figure 2).
· Adjust the angle of Bracket A to the desired posion and sure the posion with locking screw, steel gasket and nut on both sides (Figure 3).
· Aach the bracket to the ceiling or wall.
· Make appropriate electrical connecons.
Bracket B
Screws
Bracket A
Bracket B
Nut
Stainless Steel Gasket
Nylon Gasket
Nylon Gasket
Bracket B
Stainless Steel Gasket
Screws
Bracket A
Bracket A
SURFACE MOUNTED WITH MOUNTING BRACKET
Screw
Stainless Steel Gasket
Nut
TURN OFF POWER FROM MAIN CIRCUIT BREAKER
SUSPENDED MOUNTING
· Insert wires through the provided hook and screw the hook to the driver housing (Figure 1). Tighten the provided screw to secure the hook (Figure 2).
· Hang the fixture to customer supplied chain or mounng hardware (Figure 3).
· Tighten hook’s screw to secure the installaon (Figure 4).
· Make appropriate electrical connecons.
Screw Hole
Screw
Screw
Figure 1 Figure 2 Figure 3 Figure 4