imageHOLDERS SlimLine 10 Plus User manual

Slimline Wall Mounted Tablet Enclosure
Range Instructions
AMounting the Enclosure and Power Cabling
[Note: Blue Cable showing cable routing for cavity wall installations]
Position Rear Enclosure (A) on surface in desired position.
Ensure the unit is level using a spirit level (G).
[Tip: loosely screw in through top centre screw hole, as highlighted, to hold unit in
position]
Screw in remaining screws (F) using E.
[Note: We recommend using at least 4 of the 7 screw holes as shown]
Depending on your chosen surface it may be easier to;
- Mark the centre of the holes with a pencil (H).
- Drill pilot holes and install raw plugs if required.
A3 - Enclosure Mounting and Cavity Wall Power Cabling
A2 - Insert Power Cable
A1 - Removing the Tablet Cassette
Unlock both locks on either side of Ausing
the keys provided (D)
Push up Cto release from A.
[Tip: Keep one hand on the enclosure
and one on Cassette]
With Creleased lift clear of A.
If using a cavity wall for power supply, skip to Step 4.
Insert your Tablet’s Power Cable through the small cut out in the
back of Aand channel into the small cable cut out.

Slimline Wall Mounted Tablet Enclosure
Range Instructions
B/CStandard Tablet Loading and Cabling
Slimline+ Additional Device Fitting
C2 - Device Fitting and PowerC1 - Slimline+ Device Fitting
B3 - Cassette LoadingB2 - Standard Power Cabling
B1 - Tablet Loading
Thumb
Screws
Lift the Tablet Tray (B) out of the
Cassette (C)
Turn on your Tablet and place it in the
Tablet Tray (B)
Slide the Tablet Tray (B) back into the
Cassette (C)
With the tablet fitted, plug in your tablet’s power cable.
[Location may vary from the options shown above]
Position Cinto A, just above centre to locate.
Push down to fully close.
Remove highlighted thumb screws to release the
Device Tray.
Connect your power supply to your tablet, fit the NFC reader to
the top of the Device Tray and connect the device to your tablet.

Slimline Wall Mounted Tablet Enclosure
Range Instructions
Slimline+ Additional Device Fitting
C
Install Conduit (Optional)Lock Your Enclosure
C4 - Cassette LoadingC3 - Device Mounting
Secure the Device Tray in place using the thumb screws.
Stowe excess cable in the remaining space of the device
tray and ensure no cables interfere with the tray locating pins
(circled).
Lock the Enclosure by pushing in the Push Lock Pins. Tip: Use cable conduit for added security and aesthetics.
Your Slimline(+) Tablet Enclosure is ready for use.
Position the Tablet Cassette (C) into the Rear Enclosure (A) just
above centre to locate and push down to fully close.

Slimline Wall Mounted Tablet Enclosure
Range Instructions
172mm
70mm 20mm
RFID USB
USB
HUB
To Tablet
To Power
To Tablet USB
HUB
Card Reader
Mounted on the Bezel
To Power
To Tablet
Example Device Tray Configurations
D
Make Your Own ConfigurationConfiguration 3 - NFC Reader
Configuration 2 - Card SwipeConfiguration 1 - NFC Reader
Tablet:
- Samsung Galaxy Tab A
Devices:
- Lava Link USB Hub
- Magtek Dynamag
Tablet:
- Linx 10-10
Devices:
- ACS ACR122U
Tablet:
- Samsung Galaxy Tab A
Devices:
- Lava Link USB Hub
- ACS ACR122T
Other configurations are available, use the below dimensions as
a guide to what can be fitted and discuss your requirements with
our team