imageHOLDERS Shell+ 12 User manual

[phone] | 1-888-858-9778 | [e-mail]
Unit B8, Arena Business Centre, Nimrod Way, Wimborne, Dorset. BH21 7UH.
© imageHOLDERS Ltd. All rights reserved
Shell+ 12 Wall Mounted Tablet Enclosure
Instructions
017_12_161
Contents:
A - Wall Mount Bracket Installation
B - Cable Routing Options
C - Enclosure and Tablet Fitting Applicable To:
A - Rear Enclosure
B - Tablet Tray
C - Bezel and Cassette
D - Enclosure Key
E - Allen/Hex Key
F - Wall Mount Bracket
G - Wood Screws (5mm max. Diameter)
H - M5 Washers (to be used with G)
I - M4 x 8mm Buttonhead Screws
J - M4 Washers (to be used with I)
K - Pencil
L - Philips Screwdriver
M - Spirit Level
N - Drill (depending on chosen mounting surface)
A
G
F
ED
CB
H
Additional Items Required
Items Supplied
M
L
KN
I
J

Shell+ 12 Wall Mounted Tablet Enclosure
Instructions
[phone] | 1-888-858-9778 | [e-mail]
Unit B8, Arena Business Centre, Nimrod Way, Wimborne, Dorset. BH21 7UH.
© imageHOLDERS Ltd. All rights reserved
A/B 017_12_161
Applicable To:
Wall Mount Bracket Installation
Cable Routing Options
B3 - Standard Method
B2 - Enclosed Power Brick
B1 - External Power Brick
B - Cable Routing Options
A2A1 - Wall Mount Install
There are three ways of routing your power
cables;
B1 + B2 if your Tablet Device has a
Transformer/Power Brick connected to the
cable.
B3 if you have a standard USB connection
power cable.
Before fitting the Rear
Enclosure (A), loop the
power cable through
the Wall Mount Bracket
(D) ensuring enough
excess cable to connect
to the tablet.
Standard USB power cable
method - Follow the instructions
below.
Follow instructions
from C1
Place the Power Brick in the back of the Tablet Tray (B) as illustrated. Feed the
power connector through the middle slot shown in the rear view and plug into the
power brick. Connect to your Tablet.
Tip: Store excess
cable in back of B
with power brick.
Note: This method
may require a longer
figure 8 cable than
supplied by tablet
manufacturer.
Screw in Fusing screw provided (G) or your own alternative
screw (5mm max. diameter, surface dependent).
Position Wall Bracket (F) in desired position. Ensure it is level
using a spirit level (M).
Mark the centre of the holes with a pencil (K) and remove F.
Note: Drill pilot holes and install Raw Plugs if required by chosen surface.
Note:
Centre of Bracket =
Centre of Screen.

Shell+ 12 Wall Mounted Tablet Enclosure
Instructions
[phone] | 1-888-858-9778 | [e-mail]
Unit B8, Arena Business Centre, Nimrod Way, Wimborne, Dorset. BH21 7UH.
© imageHOLDERS Ltd. All rights reserved
017_12_161
Applicable To:
Enclosure and Tablet Fitting
C
C3 - Tablet Loading and Cable Routing
C2b - External Power BrickC2a - Rear Enclosure Mounting
C1 - Removing the Tablet Cassette
Place Aon F, aligning
mounting holes. Mount
with top screw first and
then fit remaining screws
as shown in detail view.
Push up Cto release from A. With Creleased, pull clear of A.
Unlock your Shell+ using Don both locks
located either side of the Enclosure (A).
If following B1 cable
routing configuration.
Ensure cable is fed through
mount and enclosure
before installing.
Lift Bout of Cpulling up the tab provided.
(Highlighted above)
Feed your cable(s) through central cut-out
in the tablet tray and plug into your tablet.
Turn your Tablet on and place into B.
Slide Bback into C, with the cable
through the tray as highlighted above.
Note: Ensure your tablet is turned on!

Shell+ 12 Wall Mounted Tablet Enclosure
Instructions
[phone] | 1-888-858-9778 | [e-mail]
Unit B8, Arena Business Centre, Nimrod Way, Wimborne, Dorset. BH21 7UH.
© imageHOLDERS Ltd. All rights reserved
017_12_161
Applicable To:
CEnclosure and Tablet Fitting
Installation Complete
C7 - Visual CheckC6 - Install Conduit
C5 - Lock Your EnclosureC4 - Fitting the Tablet Cassette
Position Cback into Ajust
above centre to locate and push
down to secure location.
Tip: ensure excess cable
is stored within A, and not
trapped between Cand A.
Tip: Use cable conduit for
security and aesthetics.
Turn your power
supply on at the mains.
Push in the Push Locks
to secure your tablet in
the enclosure.
With your
Tablet installed
and connected.
Your Wall Mounted Shell+ Tablet
Enclosure is ready for use.
Your Enclosure and cabling
should look like this from the
side.