CRU Dataport Data Express DE200 SCSI User manual

Rugged, Reliable, Mobile, SecureTM
1-800-260-9800 www.CRU-DataPort.com
Data Express DE200 Ultra160 SCA Install Guide
Removable SCSI Wide Ultra160 Drive Enclosure
Note: Installation of drive cover is necessary for proper fan air flow.
Option Pin Connector (W1)
Remote Unit ID Selection: Pins 1-8 of this connector are provided for
remote unit SCSI ID selection through the computer system. Remote
ID selection requires that the unit ID switch located on the inside of the
receiving frame be set to “0”. (Onboard ID selection is set with a switch
located on the inside of the receiving frame.)
Factory-Installed Jumpers: There are three (3) jumpers factory-
installed on W1. These jumpers are located on pins 9 & 10, pins 19 & 20
and pins 21 & 22.
Note: Do not remove these jumpers.
Fan Fault LED/Alarm Temporary Disable Jumper Option (pins 17 &
18):
No Jumper (Factory Default) – Fan Fault LED and Alarm will both func-
tion when either fan fails.
Jumper on Pins 17 & 18 - When the provided jumper is installed it
will disable both Fan Fault LED and Alarm in the event of a single
fan failure. The Fan Fault LED and Alarm will both function should
the second fan fail.
Note: This jumper must be removed once the faulty fan is replaced.
Enable Termination Power Connector (J4): This jumper is installed
at the factory and enables termination power to/from the SCSI bus.
Note: Do not remove this jumper!
Factory-Installed Jumpers (J3): There are two (2) jumpers factory
installed on J3. One jumper is located on pins 7 & 8, the other is on
pins 9 & 10.
Note: Do note remove jumpers!
Figure 1: Drive Installation Overview
Notes: For SCSI Ultra 160 operation, the DE200 Ultra160 SCA
requires Ultra160 chassis and cabling.
Figure 2: Receiving Frame Motherboard (rear view)

Rugged, Reliable, Mobile, SecureTM
1-800-260-9800 www.CRU-DataPort.com
Note: The lock on the Data Express receiving frame functions as a
lock and a DC power switch for the unit. The lock must be engaged
(turned counterclockwise) in order to supply power to the carrier and
power the unit on.
Limited Product Warranty
CRU-DataPort (CRU) warrants the Data Express DE200 to be free
of significant defects in material and workmanship for a period of
five years from the original date of purchase. CRU’s warranty is
nontransferable and is limited to the original purchaser.
Limitation of Liability
The warranties set forth in this agreement replace all other warran-
ties. CRU expressly disclaims all other warranties, including but not
limited to, the implied warranties of merchantability and fitness for a
particular purpose and non-infringement of third-party rights with re-
spect to the documentation and hardware. No CRU dealer, agent or
employee is authorized to make any modification, extension, or ad-
dition to this warranty. In no event will CRU or its suppliers be liable
for any costs of procurement of substitute products or services, lost
profits, loss of information or data, computer malfunction, or any other
special, indirect, consequential, or incidental damages arising in any
way out of the sale of, use of, or inability to use any CRU product or
service, even if CRU has been advised of the possibility of such dam-
ages. In no case shall CRU’s liability exceed the actual money paid for
the products at issue. CRU reserves the right to make modifications and
additions to this product without notice or taking on additional liability.
Certification
EMI Standard: FCC Part 15 Class B, CE
EMC Standard: EN55022, EN55024
FCC Certification
This device has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received; includ-
ing interference that may cause undesired operation.
Register your product at www.CRU-DataPort.com
A7-200-0003 Rev. 1.0
The DE200 drive carrier contains two (2) front mounted drive carrier
fans for enhanced heat dissipation. Should the fans ever fail, the unit
ID number indicator (located on the front of the receiving frame) will
display a flashing “F” and the audible alarm will sound.
Notes: The DE200 has a Fan Fault LED and Alarm feature in the
event of a fan failure. In the event of a single fan failure the Fan
Fault LED and Alarm feature may be disable.
With this jumper installed the Fan Fault LED and Alarm will still
function in the event of total fan failure.
This jumper must be removed once the fault fan is replaced.
In the case of fan failure, both fans are field replaceable. Please contact
CRU Support for a replacement fan.
Figure 3: Receiving Frame Unit ID Number and Activity Display
Figure 4: Unit ID Select Switch Location