Impex MARCY PLATINUM MP-3100 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MP 3100
Retain This
Manual for
Reference
01-27-05
OWNER'S
MANUAL
MARCY PLATINUM
MP 3100
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICES..................................................................... 2
HARDWARE PACK….......…............................................. ……………………. 3
ASSEMBLY INSTRUCTIONS...........................................……………………… 7
EXPLODED DIAGRAM……………………………………………………………... 20
PARTS LIST…………………………………………………………………………. 22
WARRANTY.................................................................................................…. 23
ORDERING PARTS.......................................................................................… 23
BEFORE YOU BEGIN
Thank you for selecting the MARCY PLATINUM MP3100 by IMPEX INC.
For your safety and benefit, read this manual carefully before using the
machine. As a manufacturer, we are committed to provide you complete
customer satisfaction. If you have any questions, or find there are
missing or damaged parts, we guarantee you complete satisfaction
through direct assistance from our factory. To avoid unnecessary delays,
please call our TOLL-FREE customer service number. Our Customer
Service Agents will provide immediate assistance to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]m

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire
manual before you assemble or operate your machine. In particular, note the following
safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

HARDEWARE PACK
3

HARDEWARE PACK
4

HARDEWARE PACK
5

HARDEWARE PACK
6

ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches.
It is recommended two or more people assembling this machine to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Attach the Left & Right Base Frames (#7 & 8) to the Rear Vertical Frame (#3). Align the holes
and secure with two M10 x 2 ½” Carriage Bolts (#91), Ø ¾” Washers (#101), and M10 Aircraft
Nuts (#98). DO NOT tighten all the Nuts and Bolts yet.
B.) Attach the Weight Glide Base (#5) to the Rear Vertical Frame. Align the holes and secure
with two M10 x 2 ¾” Carriage Bolts (#90), ؾ” Washers (#101), and M10 Aircraft Nuts (#98).
C.) Slide two Lower Safety Frames (#12) onto the Front Vertical Beams (#1). Use a M18 Lock
Knob (#52) to lock each Safety Frame at selected slot.
D.) Attach one Front Vertical Beam (#1) to the Right Base Frame (#8). Secure it with two M10 x 2
¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#25), two Ø ¾” Washers (#101), and two M10
Aircraft Nuts (#98). Repeat the same step to install the other Front Vertical Beam.
E.) Attach the Front Top Beam (#6) to the Front Vertical Beams. Secure each end with two M10
x 2 ¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#25), two Ø ¾” Washers (#101), and two
M10 Aircraft Nuts (#98).
7

STEP 2 (See Diagram 2)
A.) Attach the Weight Glide Post (#4) onto the Weight Glide Base (#5). Secure it with four M10 x
¾” Carriage Bolts (#92), ؾ” Washers (#101), and M10 Aircraft Nuts (#98). DO NOT tighten
all the Nuts and Bolts yet.
B.) Slide the Sliding Weight Post (#15) onto the Weight Glide Post (#4). Attach two Olympic
Sleeves (#48) to the Posts. Attach a Spring Clip (#50) to each Sleeve.
C.) Attach the rear of Upper Frame (#2) to the Weight Glide Post (#4). Secure it with one 3 1/8” x
1 ¾” Bracket (#27), M10 x 2 3/8” Allen Bolt (#86), Ø ¾” Washer (#101) to the upper hole.
Secure the lower hole with one M10 x 2 ½” Carriage Bolt (#91), Ø ¾” Washer (#101), and
M10 Aircraft Nut (#98).
D.) Secure the Upper Frame (#2) to the Rear Vertical Frame (#3) with two M10 x 2 ¾” Carriage
Bolts (#90), one 4¾”x2” Bracket (#25), two ؾ” Washers (#101) and M10 Aircraft Nuts (#98).
E.) Secure the Upper Frame to the Front Top Beam with two M10 x 2 ½” Carriage Bolts (#91),
one 4 3/8” x 1 ¾” Bracket (#26), two Ø ¾” Washers (#101), and two M10 Aircraft Nuts (#98).
F.) Securely tighten all Nuts and Bolts previously installed.
8

STEP 3 (See Diagram 3)
A.) Insert a Guide Rod (#18) through the hole on the right Lower Safety Frame (#12) into
the hole on the Right Base Frame (#8). Secure the Guide Rod from the bottom with
one M10 x 1” Allen Bolt (#87) and Ø ¾” Washer (#101). Slide a Ø 2 ½” x 1” Rubber
Bumper (#66) and Glider (#17) from the top onto the Guide Rod (#18). Attach the Top
Connecting Bracket (#9) onto the right Front Vertical Beam (#1) and Guide Rod. Secure
it with two M10 x 1” Allen Bolts (#87) and Ø ¾” Washers (#101). Repeat the same step
to install the other Guide Rod.
B.) NOTE: Help of another person is strongly recommended for this step. Place the Lifting
Sleeve (#16) in between the two Gliders (#17). Insert the Weight Bar (#19) into the
Glider from one end and through the Lifting Sleeve (#16) to the other Glider on the
opposite end. Secure each Glider with one M8 x 3/8” Allen Bolt (#96).
C.)Attach a Long Olympic Sleeve (#49) to each end of the Weight Bar. Attach a Spring
Clip (#50) to each Long Olympic Sleeve.
9

STEP 4 (See Diagram 4)
A.) Attach the Butterfly Base (#10) to the front of Rear Vertical Frame (#3). Attach the
Butterfly Pulley Support (#11) to the back. Align the holes and secure them together with
two M10 x 2 ½” Carriage Bolts (#91), Ø ¾” Washers (#101), and M10 Aircraft Nuts (#98).
B.) Attach the Right Butterfly (#13) to the right hole on the Butterfly Base. Secure it with one
Lock Ring (#71), Ø1½” Washer (#78), M6x1¼” Allen Bolt (#93), and M6 Aircraft Nut (#99).
C.)Attach a Butterfly Arm Pad (#43) to the Right Butterfly. Secure it with two M8 x 2 3/8” Allen
Bolts (#89) and Ø 5/8” Washers (#102).
D.)Repeat the Procedures B & C above to install the Left Butterfly (#14).
E.) Attach the Butterfly Backrest Board (#42) to the Rear Vertical Frame (#3). Secure it with
two M8 x 2 3/8” Allen Bolts (#89) and Ø 5/8” Washers (#102).
10

CABLE LOOP DIAGRAM
11

STEP 5 (See Diagram 5 & Cable Loop Diagram)
A.) Attach a 124” Cable (#38) to the front opening on the Upper Frame (#2). Attach a Pulley (#72)
to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#104), two Ø 1” x 5/8” Pulley
Bushings (#103), and one M10 Aircraft Nut (#98). Make sure the ball stopper on the Cable is
underneath the Frame.
B.) Draw the Cable over the Pulley along the Upper Frame to the opening on the rear of Upper
Frame. Attach a Pulley to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#104), two Ø
1” x 5/8” Pulley Bushings (#103), and one M10 Aircraft Nut (#98).
C.)Draw the Cable around the Pulley then downward. Install a Pulley in between the two Double
Floating Pulley Brackets (#23). Secure the Pulley with one M10 x 1 ¾” Allen Bolt (#88), two Ø
¾” Washers (#101), and one M10 Aircraft Nut (#98). Let the Bracket hanging for now.
D.)Draw the Cable around the Pulley then up to the opening on the upper Weight Glide Post (#4).
Attach a Pulley to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#86), two Ø 1” x ½”
Pulley Bushings (#51), and one M10 Aircraft Nut (#98).
E.) Draw the Cable around the Pulley then down to the Sliding Weight Post (#15). Secure the
Cable to the Post with one M10 x 1” Allen Bolt (#87), two Ø ¾” Washers (#101), and one M10
Aircraft Nut (#98).
F.) Connect the Lat Bar (#22) to the Cable with a Short Chain (#46) and two C-Clips (#47).
12

STEP 6 (See Diagram 6 & Cable Loop Diagram)
A.) Attach one end of the 79” Butterfly Cable (#39) to the hook on the Left Butterfly
(#14). Draw the Cable to the left open bracket on the Butterfly Pulley Support (#11).
B.) Attach a Pulley to the bracket and secure it with one M10 x 1 ¾” Allen Bolt (#88),
two Ø ¾” Washers (#101), and one M10 Aircraft Nut (#98).
C.)Draw the Cable around the Pulley then downward. Attach the Cable to a Single
Floating Pulley Bracket (#21). Repeat the procedure B above to install a Pulley.
D.)Draw the Cable upward to the right open bracket on the Butterfly Pulley Support.
Repeat procedure B above to install a Pulley.
E.) Draw the Cable over the Pulley then clip to the Right Butterfly (#13).
DIAGRAM 6
13

STEP 7 (See Diagram 7 & Cable Loop Diagram)
A.) Attach a 124” Cable to the lower opening on the Rear Vertical Frame (#3). Attach a
Pulley to the opening. Secure them with one M10 x 2 3/8” Allen Bolt (#86), two Ø 1”
x ½” Pulley Bushings (#51), and one M10 Aircraft Nut (#98).
B.) Draw the Cable underneath the Pulley to the open bracket on the Weight Glide
Base (#5). Install a Pulley with one M10 x 1 ¾” Allen Bolt (#88), two Ø ¾” Washers
(#101), and one M10 Aircraft Nut (#98).
C.) Draw the Cable around the Pulley then upward to the Double Floating Pulley
Bracket (#23) previously installed in Step-5. Install another Pulley.
D.) Draw the Cable around the Pulley then downward to the open bracket on the back
of Rear Vertical Frame. Install a Pulley.
E.) Draw the Cable around the Pulley then upward to the Single Floating Pulley Bracket
(#21) previously installed. Secure the Cable to the Bracket with one M10 x 1” Allen
Bolt (#87), two Ø ¾” Washers (#101), and one M10 Aircraft Nut (#98).
F.) Adjust the tension of the Cables by adjusting the Pulley position on the Double
Floating Pulley Bracket (#23). If the Cables are too loose, move up the Pulley. If
the Cables are too tight, move down the Pulley.
G.) Connect a Shiver Bar (#20) to the Cable with a Long Chain (#45) and two C-clips
(#47).
14

DIAGRAM 7
15

STEP 8 (See Diagram 8)
A.) Attach the Main Seat Support (#28) to the Front & Rear Stabilizers (#29 & 33). Secure
each end with two M10 x ¾” Allen Bolts (#83) and Ø ¾” Washers (#101). DIAGRAM 8
16

STEP 9 (See Diagram 9)
A.) Attach the Backrest Supports (#30) to the pivot on the Main Seat Support (#28). Secure
it with one M12 x 5 ¾” Allen Bolt (#82), two Ø 1” Washers (#100), and one M12 Aircraft
Nut (#97). Do not over tighten the Nut and Bolt, make sure the Backrest Support is
able to swivel.
B.) Attach the Backrest Incline Support (#31) to the Backrest Supports (#30). Secure it with
one M12 x 5 ¾” Allen Bolt (#82), two Ø 1” Washers (#100), and one M12 Aircraft Nut
(#97). Attach the Backrest Incline Support (#31) to the selected slot on the Main Seat
Support (#28) to obtain the desired Backrest incline position.
C.) Place the Backrest Board (#41) onto the Backrest Supports (#30). Secure it with four
M8 x 1 5/8” Allen Bolts (#85) and Ø 5/8” Washers (#102).
D.) Place the Seat Pad (#40) onto the Main Seat Support. Secure it with four M8 x 1 5/8”
Allen Bolts (#85) and Ø 5/8” Washers (#102). DIAGRAM 9
17

STEP 10 (See Diagram 10)
A.) Attach the Leg Developer (#32) to the open bracket on the front of Main Seat
Support (#28). Secure it with one M10 x 3 1/8” Allen Bolt (#81), two Ø ¾” Washers
(#101), and one M10 Aircraft Nut (#98). Do not over tighten the Nut and Bolt. Make
sure the Leg Developer is able to swivel.
B.) Insert the U-shaped Lock Pin (#37) into the tube in the front of Main Seat Support.
Secure it with one Spring (#80), Ø ½” Washer (#79), and M6 x ½” Philips Screw
(#95).
C.) Insert three Foam Tubes (#36) halfway through the holes on the Main Seat Support
and Leg Developer. Push six Foam Rolls (#76) onto the Tubes from both ends.
Plug six Foam Roll End Caps (#61) into the Tubes from both ends.
D.) Attach an Olympic Sleeve (#48) onto the weight post on the Leg Developer. Attach a
Spring Clip (#50) to the Olympic Sleeve.
E.) Attach a Curl Bar Holder (#35) to the Leg Developer. Secure it with a L-shaped Pin
(#77).
DIAGRAM 10
18

STEP 11 (See Diagram 11)
A.) Attach the Arm Curl Pad (#44) to the Arm Curl Stand (#34). Secure it with two M8 x ¾”
Allen Bolts (#84) and Ø 5/8” Washers (#102).
B.) Insert the Arm Curl Stand into the front opening on the Main Seat Support. Use a M18
Lock Knob (#52) to secure the Stand at desired height.
C.) The Leg Developer can be locked when doing sit up exercise. Simply pull the U-
shaped Lock Pin out and drop into the hole on the Leg Developer. Remove the Pin
when doing Leg Developer exercise.
D.) Remove the Arm Curl Stand and the Curl Bar Holder when using the Leg Developer.
DIAGRAM 11
19