Impex MARCY PLATINUM MP-3105 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MP-3105
Retain This
Manual for
Reference
12-27-06
OWNER'S
MANUAL
MARCY PLATINUM
SMITH CAGE
MP-3105
IMPEX®
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICES..................................................................... 2
HARDWARE PACK….......…..........................................………………………. 4
ASSEMBLY INSTRUCTIONS...........................................……………………. 8
EXPLODED DIAGRAM…………………………………………………………….. 23
PARTS LIST………..……………………………………………………………….. 25
WARRANTY.................................................................................................…. 26
ORDERING PARTS.......................................................................................… 26
BEFORE YOU BEGIN
Thank you for selecting the MARCY PLATINUM Smith Cage MP-3105 by
IMPEX®. For your safety and benefit, read this manual carefully before
using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there are
missing or damaged parts, we guarantee you complete satisfaction through
direct assistance from our factory. To avoid unnecessary delays, please call
our TOLL-FREE customer service number. Our Customer Service Agents
will provide immediate assistance to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]m

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire
manual before you assemble or operate your machine. In particular, note the following
safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
5. Maximum weight on Rack: 600 lbs.
6. Maximum weight on Smith Bar: 300 lbs.
7. Maximum weight on Weight Holder: 200 lbs.
8. Maximum weight on Leg Developer: 100 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS. 2

WARNING LABEL REPLACEMENT
The warning labels shown here have been placed on the Cross Brace, Rear Stabilizer, and Upper
Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for
replacements. Apply the labels in location shown.
3

HARDEWARE PACK
4

HARDEWARE PACK
5

HARDEWARE PACK
6

HARDEWARE PACK
7

ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches.
NOTE: It is strongly recommended two or more people assembling this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) NOTE: Do not tighten the Nuts and Bolts until instructed to do so.
B.) Attach one Diagonal Support (#3) to the Right Cross Brace (#15). Secure it with one 3
¾” x 2 3/8” Bent Bracket (#26), M10 x 2 3/8” Carriage Bolt (#81), Ø ¾” Washer (#87),
and M10 Aircraft Nut (#89) to the front hole. Secure the back hole with one M10 x 2
1/8” Allen Bolt (#74) and Ø ¾” Washer (#87). Repeat the same procedure to install the
other Diagonal Support to the Left Cross Brace (#14).
C.) Attach the Left & Right Cross Brace (#14 & #15) to the Rear Vertical Beam (#10).
Secure them together with two M10 x 2 ¾” Carriage Bolts (#83), Ø ¾” Washers (#87),
and M10 Aircraft Nuts (#89).
D.) Attach the Foot Plate (#34) to the front of Rear Vertical Beam (#10). Attach the Weight
Glide Post Base (#11) to the back of Rear Vertical Beam. Align the holes and secure
them together with two M10 x 2 3/8” Allen Bolts (#75), four Ø ¾” Washers (#87), and
two M10 Aircraft Nuts (#89).
E.) Secure the Foot Plate (#34) to the Rear Vertical Beam (#10) with one M10 x 3” Allen
Bolt (#77), two Ø ¾” Washers (#87), and one M10 Aircraft Nut (#89).
8

DIAGRAM 1
9

STEP 2 (See Diagram 2)
A.) Attach the Left Vertical Beam (#1) to the left Diagonal Support (#3). Secure it with two M10
x 2 ¾” Carriage Bolts (#83), one 4 3/8” x 2 ¾” Bent Bracket (#25), two Ø ¾” Washers
(#87), and two M10 Aircraft Nuts (#89).
B.) Attach one Guide Rod (#5) onto the left Diagonal Support. Secure it with one M10 x 1”
Allen Bolt (#72) and Ø ¾” Washer (#87) from the bottom.
C.)Slide a Ø 2 ½” x 1” Rubber Bumper (#65) and the Left Safety Stop Frame (#7) onto the
Guide Rod from the top.
D.)Attach a Guide Rod Bracket (#4) onto the Guide Rod (#5) and the Left Vertical Beam (#1).
Secure it with three M10 x 1” Allen Bolts (#72) and Ø ¾” Washers (#87).
E.) Repeat Procedure A to D above to install the other side.
10

STEP 3 (See Diagram 3)
A.) Place the Weight Glide Post (#12) onto the Weight Glide Post Base (#11). Secure it
with four M10 x ¾” Carriage Bolts (#79), Ø ¾” Washers (#87) and M10 Aircraft Nuts
(#89).
B.) Slide the Sliding Weight Post (#22) onto the Weight Glide Post.
C.)Attach the Upper Frame (#13) onto the Rear Vertical Beam (#10). Secure it with two
M10 x 3 1/8” Carriage Bolts (#84), one 3 ½” x 1 5/8” Bent Bracket (#28), two Ø ¾”
Washers (#87), and two M10 Aircraft Nuts (#89).
D.)Attach the rear of Upper Frame (#13) to the Weight Glide Post (#12) and secure it with
one 2 ¾” x 1 ¾” Bracket (#29), M10 x 2 3/8” Allen Bolt (#75) and Ø ¾” Washer (#87) to
the upper hole. Secure the lower hole with one M10 x 2 ½” Carriage Bolt (#82), Ø ¾”
Washer (#87), and M10 Aircraft Nut (#89).
E.) Attach one Upper Frame Support (#16) to the Left Vertical Beam (#1). Secure it with
one 2 ¾” x 2” Bent Bracket (#27), M10 x 3 3/8” Allen Bolt (#78) and Ø ¾” Washer (#87)
to the upper hole. Secure the lower hole with one M10 x 3 ½” Carriage Bolt (#85), Ø ¾”
Washer (#87), and M10 Aircraft Nut (#89). Repeat the same step to install the other
Upper Frame Support (#16) to the Right Vertical Beam (#2).
F.) Attach the two Upper Frame Supports (#16) to the Upper Frame (#13) from each side.
Secure them together with two M10 x 2 3/8” Carriage Bolts (#81), Ø ¾” Washers (#87),
and M10 Aircraft Nuts (#89).
G.)Securely tighten all Nuts and Bolts previously installed.
11

DIAGRAM 3
12

STEP 4 (See Diagram 4)
A.) Attach the Butterfly Base (#17) to the front of Rear Vertical Beam (#10). Attach the Butterfly
Pulley Bracket (#18) to the back of Rear Vertical Beam. Align the holes and secure them with
two M10 x 2” Carriage Bolts (#80), Ø ¾” Washers (#87), and M10 Aircraft Nuts (#89).
B.) Insert the Axle on the Left Butterfly (#19) into the Butterfly Base from the bottom. Secure it
with one Lock Ring (#54), Ø 1 ½” Washer (#53), M6 x 1 ¼” Allen Bolt (#69), and M6 Aircraft
Nut (#88).
C.)Attach a Butterfly Arm Pad (#38) to the Left Butterfly (#19). Secure it with two M8 x 2 ½” Allen
Bolts (#71) and Ø 5/8” Washers (#86).
D.)Repeat Procedure B and C above to install the Right Butterfly (#20).
E.) Attach the Backrest Board (#39) to the Rear Vertical Beam (#10). Secure it with two M8 x 1
¾” Allen Bolts (#70) and Ø 5/8” Washers (#86).
13

CABLE LOOP DIAGRAM
14

STEP 5 (See Diagram 5 & Cable Loop Diagram)
A.) Attach a 123” Cable (#37) to the front opening on the Upper Frame (#13). Attach a
Pulley (#44) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#75), two Ø 1
1/8” x 3/8” Pulley Bushings (#42), and one M10 Aircraft Nut (#89). Make sure the ball
stopper on the Cable is underneath the Upper Frame.
B.) Draw the Cable over the Pulley along the Upper Frame to the opening on the rear of
Upper Frame. Attach a Pulley to the opening. Secure it with one M10 x 2 3/8” Allen Bolt
(#75), two Ø 1 1/8” x 3/8” Pulley Bushings (#42), and one M10 Aircraft Nut (#89).
C.)Draw the Cable around the Pulley then downward. Install a Pulley to the top holes on
the two Double Floating Pulley Brackets (#23). Secure the Pulley with one M10 x 1 ¾”
Allen Bolt (#73), two Ø ¾” Washers (#87), and one M10 Aircraft Nut (#89). Let the
Brackets hanging for now.
D.)Draw the Cable around the Pulley then upward to the opening on the top of Weight
Glide Post (#12). Attach a Pulley to the opening. Secure it with one M10 x 2 3/8” Allen
Bolt (#75), two Ø 1” x ½” Pulley Bushings (#40), and one M10 Aircraft Nut (#89).
E.) Draw the Cable around the Pulley then downward to the Sliding Weight Post (#22).
Secure the Cable to the Sliding Weight Post with one M10 x 1” Allen Bolt (#72), two Ø
¾” Washers (#87), and one M10 Aircraft Nut (#89).
F.) Connect the Lat Bar (#21) to the Cable with a Short Chain (#47) using two Hooks (#48).
15

DIAGRAM 5
16

STEP 6 (See Diagram 6 & Cable Loop Diagram)
A.) Attach one end of the 79” Butterfly Cable (#36) to the clip on the Left Butterfly (#19). Draw the
Cable to the left Butterfly Pulley Bracket (#18).
B.) Attach a Pulley (#44) to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#73), two ∅¾”
Washers (#87), and one M10 Aircraft Nut (#89).
C.)Draw the Cable around the Pulley then downward. Attach the Cable to a Single Floating Pulley
Bracket (#24). Install a Pulley to the Bracket. Let the Bracket hanging for now.
D.)Draw the Cable around the Pulley then upward to the right Butterfly Pulley Bracket. Install
another Pulley. Draw the Cable around the Pulley then clip to the Right Butterfly (#20).
17

STEP 7 (See Diagram 7 & Cable Loop Diagram)
A.) Attach one 123” Cable (#37) to the lower opening on the Rear Vertical Beam (#10). Attach
a Small Pulley (#45) to the opening. Secure it with a M10 x 2 ¾” Allen Bolt (#76), two Ø 1”
x 5/8” Pulley Bushings (#41), and one M10 Aircraft Nut (#89).
B.) Draw the Cable underneath the Pulley to the open bracket on the Weight Glide Post Base
(#11). Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#73), two ∅
¾” Washers (#87), and one M10 Aircraft Nut (#89).
C.)Draw the Cable around the Pulley then upward to the Double Floating Pulley Bracket (#23)
previously installed in Step-5. Install a Pulley.
D.)Draw the Cable around the Pulley then downward to the open bracket on the back of Rear
Vertical Beam (#10). Install a Pulley then draw the Cable upward to the Single Floating
Pulley Bracket (#24) installed in Step-6. Secure the end of the Cable to the bracket with
one M10 x 1” Allen Bolt (#72), two ∅¾” Washers (#87), and one M10 Aircraft Nut (#89).
E.) Connect the V Bar (#35) to the Cable with a Long Chain (#46) using two Hooks (#48).
F.) Check the tension of the Cables. If the Cables are too loose, adjust the tension by moving
up the Pulley on the Double Floating Pulley Bracket (#23). If the Tension is too tight, then
move down the Pulley.
18

STEP 8 (See Diagram 8)
A.) Note: Help of another person is strongly recommended for this step. Place the Weight
Lifting Sleeve (#6) in between the two Safety Stop Frames (#7 & #8). Align the holes
and insert the Weight Bar (#9) into the Left Safety Stop Frame through the Weight
Lifting Sleeve to the other end of Right Safety Stop Frame. Turn the safety hooks on
the Weight Lifting Sleeve to secure its position on the selected slot of the Vertical
Beams (#1 & #2). Center the Weight Bar and secure it to the Left & Right Safety Stop
Frames with two M8 x 3/8” Allen Bolts (#90) on each end.
B.) Slide two Olympic Sleeves (#50) onto the Sliding Weight Post (#22). Slide two Long
Olympic Sleeves (#51) onto the Weight Bar (#9).
C.)Attach four Spring Clips (#49) to the Olympic Sleeves.
D.)Attach the Left & Right Bar Holders (#32 & #33), Left & Right Safety Catches (#30 &
#31) onto the selected peg on the Left & Right Vertical Beams.
DIAGRAM 8
19